Just purchased some cut proof gloves!

So you don't need your old key remote to program a new key remote

👌🏻👌🏻👌🏻tnx

Really useful, and explained clearly. Thanks

There is a dust shield rubber, you can apply it on the clutch master cylinder. Finish code 1486717. Here is my replace mytdci.blogspot.com/2011/01/ha-olajos-lett-bal-cipod-tul-162000-km.html

Good

God job, very well put together.👍 💯

You should do a engine service video next 👍

That's pretty cool. I thought you were going to change both sides, since the wear is not equal on both sides.

Great video! I've noticed in couple of your videos that your frame rate on your camera is not aligned with the lights in your garage, thats why they are flickering on the video

We should join forces. I replaced my '03 Focus CV axles when I replaced it's clutch. Then I replaced the CV axles on my friend's '08 Outback. I also replaced the output shaft seals while I was at it, and also replaced the gear oil. Each car took longer than 15 minutes.

Where do u get torque specs from?

Great work, i will use this video to change the alternator in my Mazda Tribute 2.0 Zetec 2002j. thanks for you work

one of the coolest toys on the market thumbs UP! (steering wheel's on the wrong side tho') 😂

This Eric guy is so amazing in explain things very clearly. I've always enjoy learning from him, his clean work space, professional and knows his shit.

Just did it on mine 2 weeks ago thanks for the vid

i'm going to pull the seats out of mine right now to see if i can find a pen too.

Я из России у меня фокус 1 седан, двигатель такой же 1.8 zetec , отличный автомобиль, я так понимаю это Австралия🇦🇺

You should do a vacuum line video!!!!

A1 tutorial.

Hey man, first of all, thank you so much for the video. I did the timing belt change :D. I tried to hear the cars sound before I did the change but the battery was dead and I didnt have a jump starter so went ahead with the change, also changed the serp belt, timign belt tensioner, idler and cam and crank seals. I then bought a powerbank to jump start and then started the car up. It runs fine-ish. So I also had to follow some of the steps from kzfaq.info/get/bejne/fbl4nNqBncfPo58.html&ab_channel=1AAuto%3ARepairTips%26SecretsOnlyMechanicsKnow since they did a more step by step tear down of the vehicle. so for the engine mount I torqued the bolts on the engine to 80nm and the ones on the chasis to 50nm. - The car vibrates very slightly when I climb hills, I guess I have to torque down the bolts to 80nm - Theres a slight ticking noise, idk if this was there before or if the belt tensioner is not adjusted correctly or if its just the fuel injectors clicking, I uploaded a video here -> kzfaq.info/get/bejne/l5p-oZmmup-aiKs.html&ab_channel=SaifAbdulCassim - Do you think I have to be worried about the clicking? does your car make a similar noise? its coming from near the back of the engine, as I said I dont have sounds from before the repair to directly compare since the battery was dead, but last it ran I dont think it made this noise, maybe I am being paranoid. i am planning to do a coolant flush in a few weeks, I wanna use the car regularly till then, so that I can flush things out in sequence, will also do a water pump change then, was thinking I ll tear into the engine again during that time and give the timign belt tensioner and idler a final torque, what do you think?

Hey great video, could someone please help the noob here: I'm upgrading my own Mk1 focus and want to do the same thing here. vendors tell me the products are not compatible, but I believe it's due to them just taking standard listings not factoring in changing the cables. If I'm following this correctly the upgraded cables are what make this MSD coil compatible with the Mk1?

This is a great video. Thanks for all the work to put it together.

This was so helpful mate - thank you!

great vid mate going to attempt mine soon revs up allright but put in gear bogs down

I always love all the interior touches you do, just a little bit of custom, and a whole lot of make it brand new 👌

Good work bro thank you this would help me

👌

Great job mate.

3:54 thats much stiffer, 4:00 thats how hard that was :). next should have been if it was floppy it wouldnt pass a road worthy!

Good pacing, you didn't try to make an epic out of it. I could pause, do the next step, resume...exactly what I needed. BF Falcon mk I was all Phillips head 👍

Words spoken by a wise man. Isn’t it funny how we become older and even though we have more available money than we did as youngsters we turn to what’s affordable and sensible and we completely re-evaluate how we modify cars 😅

Sweet new project! We need more Cobra videos though!

Amazing project ❤ 🎉🎉🎉

Are the stock injectors up to the challenge or is an upgrade needed?

Might I suggest upgrading the lights in your garage?

WRX for the win!

Hope you liked the WRX mod plans video!... Do you have any other suggestions? Comment below 👇The best tip will get a free 3-pack of cut-proof work gloves (USA and AU only)! horusworks.com/products/cut-resistant-work-gloves

Como poder comprar estás peças pois no Brasil não tem, aqui ad peças são diferentes mais o carro é o mesmo

The only thing I'd add to this is an uprated actuator. Something like a Turbosmart unit. They hold boost so much better than the rubber diaphragm oem units. A forgotten item.

Yup. This is what I did. Pretty good fun. 🙂

Very good advise.👍

I love it when a plan comes together 😊

A handy hint - I remove the oil cap last just before taking the black coil cover off. When I do, I place a rag rolled up in a ball stuffed reasonably tight into the hole whilst removing the black coil cover. Same but opposite when putting it all back together. The last thing you want is dirt, a screw or rubber grommet from the back of the coil cover falling into the oil cap hole & ending up somewhere you can't reach it. I also put a very thin smear of copper grease on the new plug threads. Love your videos but not as much as my BA XR6 Ute. Cheers

Excellent video. There is now a two month free trial of the FORScan software. Thanks. Nice Falcon. My BFII is not as good nick, but does the job.

Just found this leaking ❤ great channel brother ❤

Excellent job and video 🎉💯

Hey mate I’m haveing trouble finding a obd2 scanner for a 2004 ba falcon, on the website it states it’s for a 2006 BA and newer, will it still work with my car? If not can you point me in the right direction 👍 video was verry helpfull nun the less