Too bad nobody told you the upper radiator support comes off in like 2 minutes and saves like an hour on this install.

Dude! Same thing happened to my maxpeeding rod coil overs in the rear. Not even 50 miles and the bushings almost shot out in the rear. I was lucky I had to adjust the height some more or else I would’ve been in big trouble. I read on a thread to just put the bolt in from the other side and that metal piece still slides into the back of the hub. Has been good so far.

Gorgeous and dependable truck❤

I want to do this when I get my car but why not just spray the black spray over everything that was grey when you seen the spray worked instead of putting the black pieces on ?

I did the same way without moving some things 😅

you can totally remove the headliner without removing any glass....

My silverado is basically this I used ppf but the flares changed the total look

Why we all keep the antenna in the same spot

No oil for PTFE seal

What type of paint did you use?

I run redline shockproof in my STI

How did it hold up? You still happy with it or would rather leave it alone if you could go back in time?

Thats how my car is. WTF would they 2 tone the interior

Same truck but doing a 2 inch level kit will same specs work?

The truck can handle the numerically lower ratio very well. I see leaving stock and enlarging the tires as a higher gear and savings on miles on the clock if you are still in warranty.

Speed is not accurate unless they reprogrammed...

Do you think you could get away with same tire and wheel setup but with a 2inch level kit with no rubbing?

i’m so glad this video exists, made up my mind to do this on my 1500, already have all the paint and dye. Gonna start the process in a few weeks

too much sh*t talking.

Thanks for posting this. Was On the fence of going cheap again like my first e39, but remembered all the shenanigans like cutting the sleeves and the stiffness. BC’s it is!

I have a question bro! Do you have to use that sealant from fcp specifically? Is there any other sealant I can use? Thanks in advance

I like how you actually show the process literally , nice vid bro thanks

Another Jerry with a J that daily's a 03 ep3 that was originally silver😂 right here

Will I blow up my truck or screw anything up running 37s and 3.42?

any difference in mpg?

Great video. It took me many attempts to, with all bc the screws. I had to rotate the crank to use a new location on the seal with the screws for each attempt. I used a torch to heat up the block around the seal, may or may not have helped. Finally got it

Dudes a nerd 🤓 nice truck tho bro i just got a rebel an tryna find a kew lil build

Did you ever compile a parts list for this project?

Oh, man, I just picked up a 2020 Warlock so I could retire my 16 Rubicon as my daily driver. Only thing I don’t like about the truck is that awful beige on the top half of the cab.

How do you like the 4.56s? Would it be a huge difference to 4.10s or possibly 4.30s?

So did this actually fix your problem?

thanks for this vid bro. a godsend for a dude with an 04 with a leaky valve cover gasket dripping oil onto his exhaust and the synchros on their way out. good to know that these are both known issues with this car.

Nice truck! What’s the part number for that s type muffler? Sounds great!

I’ve been trying to find a video to replace the interior with out paint but with cloth interior

I’m kinda sad for that m3 🤦🏻‍♂️

Send me ur number please I need u

Lame

Sweet ride!

Awesome effort with the video but I'm so sorry... No cigar. See, i was about to try this but you don't detail exactly where you need to put the jack in order to keep it (the engine?) suspended. If I'm missing something please let me know. I feel like you skimmed over that part a bit.

Great video. I have a 2014 1500 tradesman and I can’t seem to find any of the black pillars. Even all the part out trucks I’ve come across have just beige. I’m getting close to just getting a can of spray paint from Walmart 😂😂

buying the Havoc edition soon, full color match to the truck.probably run 22x10 wheels

Right up until the ball joint breaks.... change the uppers ASAP

before you regeared, did you have any flare between shifts? If so, did it go away when you put the 4.56's in?

Good video! Thanks

Could have been a 20 second video Stick to the repair Maybe start taking Ritalin just an idea

I agree with ya never understood why so many cars have a light and dark 2 tone interior. Why not all blacked out. Or all grey and let us choose one.

Did you unplug the battery while changing that pillars? And the headliner? Or no?

I know this is old. But you don’t have to remove the windshield. Headliner will slip out of the back doors on a crew cab. I know because I did it for dye and starlight headliner! Looks good man.

Lots of great information in this video. 👍👍 At first I was unsure I could watch the whole video because it seems like a fairly straightforward job other than the painful part of Dying the roof lining ??? But, you took the time to explain everything perfectly that anyone could understand. Currently looking at buying a new RAM 1500. My only complaint is the Beige interior ??? I could buy the next model up with a Black interior, this would be my only reason ?? Thanks for taking the time to put this video together, making and editing videos can be fun. Although it can be very time consuming ???

Curious what your measurements are from bottom of fenders to centers of wheels