9 ай бұрын
10 ай бұрын
10 ай бұрын
11 ай бұрын
Жыл бұрын
Жыл бұрын
Жыл бұрын
Жыл бұрын
Жыл бұрын
Жыл бұрын
Пікірлер
@naltstatt Сағат бұрын
Very very good job sir. Fantastic explanations and clear explanations. Nice job.
@jasonelliot9633 3 сағат бұрын
Good video...just you should not force multimeter leads into a connecter it can spread the terminals they have probes you can buy that are much thinner and I back probe with them
@christianmartinez7802 4 сағат бұрын
The funny part is that people in the GM side would rather compare the 6.2 and not the 5.3. The 5.3 is very underpowered for being how new it is.
@EliminatorPerformance 24 секунд бұрын
Yea I get that all the time with Rams and the 5.7 hemi, like of course it makes more power, it has more displacement lol the closest GM engine is the 4.8L because a 302ci coyote is actually 4.949L but no one wants to talk about that comparison lol
@alexmace2437 4 сағат бұрын
What causes a battery to die in a riding lawn mower I know you don't live close to me but I'm new to owning a riding lawn mower I'm just trying to figure out how to work on it so anyway you can tell me what kills off the battery and a riding lawn mower
@CARBON10 4 сағат бұрын
Most mowers have left hand thread bolts to remove blade, so it's opposite to normal, tighten to loosen or loosen to tighten. Got you now........no it's true
@NishnobsRUs 9 сағат бұрын
Nice video very clear and easy to understand 👍🏾
@samuelsmith8964 10 сағат бұрын
Nice video. My splitter auto kickback wasn't working when i started it this spring. Now I should be able to easily fix it. Thanks!
@marekzalewski8447 13 сағат бұрын
Excellent video. Very clear and helpful
@ReadyyOG 16 сағат бұрын
Thank you so much used a hair dryer and it worked!
@gluemanred 17 сағат бұрын
Great video!! I picked up the same mower a few days ago and the mower was slow to crank. The ground wire on the solenoid switch was melting the insulation off the wire too! Long story short; the previous owner had changed the solenoid but used a 4 post where the spade connectors were hot when the key was engaged. This video helped me realize there is a 4 post terminal with one being a ground!
@garybregel1572 20 сағат бұрын
I installed them on my John Deere D155 lawnmower. I notice a small difference in the turning of the lawnmower. Nothing to write home to Mother about. But every lawnmower is different. The only real difference was making small turns, they were easier. Large turns had no effect on turning in my opinion.
@williamkriebel916 21 сағат бұрын
Great video., thanks for sharing it
@caraudiofreak Күн бұрын
Thanks man!!! Never would have guessed that!
@squadman3376 Күн бұрын
McGiver lives !!
@krzysztofGagarin286 Күн бұрын
Bardzo dobry film poglądowy Pozdrawiam serdecznie z Polski Boże Błogosław Amerykę Północną i Prezydenta Stanów Zjednoczonych Ameryki
@rustyrepairs2565 Күн бұрын
I have this model. It runs poorly. Any idea what the valve lash settings are?.004 & .006? In. Ex.?
@JR-xj2vr Күн бұрын
Just use a solvent to remove the gasket leftover. It may take longer, but using any kind of a wheel is risky.
@EliminatorPerformance Күн бұрын
You are correct, but I use the blue fabric discs. I know it can be risky but I've never had any issues. I would not use the brown fabric discs, they are super abrasive. Now if this was a cylinder head on a race motor, I wouldn't be using this method lol
@JR-xj2vr Күн бұрын
@@EliminatorPerformance your video was really good. The reason I was viewing it was because I was noticing dead grass dots in my lawn….ie, a bad seal. Unfortunately, when I pulled the sump side off I noticed a lot of wear on the bearing…and to be expected after I think 20 years of service. So, I had to buy a new sump side otherwise just replacing the seal wouldn’t really fix the seal. I am really surprised the seal spring isn’t a bit stronger…to be tighter to the crank. Anyway, it’s been 20 years since I needed to dive into a 4 cycle engine so thanks for the video.
@JR-xj2vr Күн бұрын
That’s some nastyyyyyyy sludge.
@PainterD54 Күн бұрын
The new models are built too cheap. I like my 35 year old Toro with steel rods to control the drive and auger/thrower impeller. They sure don't build them for what you pay anymore.
@DontWorshipRapists-zw5si Күн бұрын
Hey Champ - I did this to my friends slighly smaller 5.5 140cc Briggs and Stratton - didn't work. IF THE SPARK PLUG IS WET -- Do you think its the ignition Coil ??? Please Please resopnd.
@EliminatorPerformance Күн бұрын
It's possible, remove the plug and pull it over a few times to dry out the cylinder. Put the plug back in, remove air filter and spray a small squirt of starter fluid in the intake. If you pull it and it doesn't fire, you likely have no spark.
@DontWorshipRapists-zw5si Күн бұрын
@@EliminatorPerformance Thank you for your prompt Response sir -- You are the Best.
@brianwoodard82 Күн бұрын
Thank you for the walk thru..just changed the carb on my weedwacker and it’s running again! Thanks
@pablocruze9307 Күн бұрын
I just found your video while searching for the same broken transmission support issue. I am elderly and not able to do this myself. What price range do you think a shop would charge to replace the brackets?
@sorungbezacheus7144 2 күн бұрын
Ok but what cause overflows in carburator.
@meshark_t 2 күн бұрын
Waste of money
@cll1out 2 күн бұрын
Recently rebuilt carb on a chain saw. It’s a very similar setup to this. I should have bought the China carb but got the rebuild kit instead. The hour and a half def wasn’t worth the $5 saved especially since one of the screens I changed really required some jewelers tools. Good thing I have some minimal cell phone repair experience. I avoided the new carb only because I had concerns on build quality. Fortunately it’s easy to confirm good spark and compression without a carb so I did that before spending money.
@EliminatorPerformance 2 күн бұрын
The best is to find the ones with lots of good reviews, spend a bit more usually not much more than an extra $10 here or there for a good carb
@adamanderson8843 2 күн бұрын
Great video. Easy to follow and understand. Very helpful. Keep ‘em coming.
@8Nguy1948 2 күн бұрын
I just inherited a Z225 that needed a drive belt, and your video was very helpful in changing it . Thanks for your help with this.
@jakecrib9971 2 күн бұрын
Excellent video. You went above it precisely as it should have been done. No corners cut. I love that.
@miguelangeld5589 2 күн бұрын
Thanks for sharing your knowledge men! Best regards from 🇨🇦
@thecaptainindustrialsales4560 2 күн бұрын
is the bore ( needle seat bore for the new neoprene gasket ( biscuit) in the carb for the needle seat , straight bore or tapered? can you measure it , and confirm?
@texasfrontiersman8245 2 күн бұрын
Does this hurt the thrust bearing?
@scgoralski 3 күн бұрын
A fantastic video! Showing the gears and bushings and how the wear occurs, and the results of the wear would give any novice diy homeowner more than enough info on attempting this repair. Thank you for uploading this! 🙏🫶
@YouTuber-mc2el 3 күн бұрын
I've got a GX200 that idles and even can take half throttle under no load. Any throttle higher and it stalls. I thought carb so I disassembled, cleaned real good and reassembled. No change. I was ready to buy a new carb but thought I'd check KZfaq. So glad I did. I took a ohm reading on mine and it was 9000. Bought a Stens from Amazon and installed. Runs like brand new. Can't thank you enough for posting this fix. Liked and subscribed. Never would even come close to thinking this would be faulty.
@EliminatorPerformance 2 күн бұрын
Glad it helped, thanks for watching!
@syedzahid4860 3 күн бұрын
Great job on explaining the detail!!!
@syedzahid4860 3 күн бұрын
Excellent and clear instruction , thank you!!!!
@mkhulusizwedlamini7608 4 күн бұрын
So much detailed information❤
@trotptkabasnbi6655 4 күн бұрын
pretty sure you mean Turtle as slowest , not rabbit at 2:15
@spambott1 4 күн бұрын
Is this the same procedure for the YT3000?
@sandrayatsko7664 4 күн бұрын
Do you install the bushings for proper spacing with this bearing conversion? Just want to make sure the wheel isn't going to rub.
@EliminatorPerformance 4 күн бұрын
I'll use washers where needed, just get some .750 ID washers and you'll be fine
@sandrayatsko7664 4 күн бұрын
Thank you!
@dschwep7 4 күн бұрын
Thanks !
@lindsayjenkins5430 4 күн бұрын
Thanks ….heading to Home Hardware for some self tapping screws! 🇨🇦😀🇨🇦😀
@PapaMav 4 күн бұрын
Luv Taryl
@FunFlyingGlobal 4 күн бұрын
Great explanation and demo!
@barbarajeanbraceletlady3090 4 күн бұрын
My TR30R won’t start, and I got a new battery. It’s started and I mowed the lawn twice. Now it won’t start. I purchased the kit for a tune up, air filter, and oil for a change. I even bought a carburetor kit. However there are no mobile services, in my area to come and install all. The local Riding Lawnmower repairman, uses another person to pickup the mower $40 then after a tuneup (when I supply the kit) charges $200. I wish someone would start a mobile service.
@EliminatorPerformance 4 күн бұрын
Check the mower deck discharge cover switch, make sure the cover didn't pop up. I have a video on that, just Google Cub Cadet CC30 won't start
@nyccotuscani6647 5 күн бұрын
Man... I searched and searched to find the exact repair video to fix my BlackMax EXI 725 for days... and finally found yours...THANK YOU SO MUCH FOR CREATING THIS VIDEO BROTHER 👍🏾
@markhardy3711 5 күн бұрын
Imo i call bs i marked my dipstick after i put 8 .8 qt oil after oil change had tsb done still burns 1qt every 1200 miles a qt of is always a qt no matter where the hash mare at on dipstick
@shanebowman10 5 күн бұрын
Sucks trying to get that snap ring back on! Tried without the rubber seal and it worked but height adjustment kept slipping off due to too much slop and slipped off the bottom tab repeatedly. Got the assembly in the freezer now. Fingers crossed I'll get it on
@darrellsomers5427 5 күн бұрын
Where do I get replacement valve guides ?
@thegamingfox523 5 күн бұрын
Would this work for a small go kart engine?