i didn't know you can get glue that comes out of a piece of paper

Battila bene, mi raccomando...anzi attaccaci elettrodi e guardala al computer😂

😂😂😂😂😂😂😂

Love your technique!!! The only thing is how did you push the wire through the glued crack that you use to hold the cleat with? Thanks in advance

Thank you for the information and demonstration. Sending warmest greetings from the San Francisco Bay Area, California, USA 🇺🇸

0:35 Why waste time doing this? Only to then cut the string off? It’s a nylon strung guitar at low tension, just cut the strings as they were and save a lot of unnecessary effort 😮🇬🇧🙏

Title: Bending Guitar SIDES by Hand... First 8 minutes of the video: Building Guitar Tops... Click-bait? Poor editing? Oh well, back to Ken Parker...

That is an extremely clever little clamp you have there. Tuning Keys - Who'd a thought.

Gracias por compartir. Thx for share!

How much a pair like that would go for today?

Hi Ad. So you tunned the top around F#…?

the absolute best vid I've seen yet on this.thanks.

Wonderful!

Bravo and thank you! I have not yet found a video detailing the reason WHY as well as it's corresponding WHAT so precisely. What a peaceful inspiration!

Fascinating I love this ❤

Awesome! coming up in the next few newby task. Thank You for sharing!

When I was young, I had a Gibson Les Paul Junior with a sunburst finish. It was in VERY GOOD condition and all original. I believed this to have been made in 1953. The number on the neck was 000006 or 0000006. It also had an Alligator Skin Guitar case and a Gibson Ga Amp which was also covered in Alligator skin. QUESTION; How much do you think this would be worth today?

Neodymium magnets are a great boon for many things- as others have pointed out, I have also used them at times for clamping cleats in place more easily than the tuner trick, as long as I have landmarks inside for positioning by feel- just want to be careful positioning cleat and inner magnet and then apply the outer one straight down rather than approaching from the side to avoid pulling the inner assembly sideways. One thing, though- when using magnets to align an initial crack glue-up, I now make a point of making sure I’ve got a bit of wax paper between the magnet and the guitar top to prevent the magnet from sticking to glue squeeze-out on the top of the instrument.

hey zomaar een gedachte he, gedurende het buigen, koel je dat metaal dan niet af, doordat je er eigenlijk steeds water op doet? Voor mij lijkt het gedurende het buigen dat het steeds minder makkelijk buigt. net alsof je je hem wat langer weer moet laten opwarmen?

The guitar playing in the background sounds like a classical adaptation of Manolo Sanlucar's ''Nacencia''. Your guitar sounds amazing.

Wow. So much ingenuity.

Gimme a break on this technique.

how how would suggest thinning a neck on a parlour guitar. It is just a bit too thick.

Hello Ad, I learned a lot in your video. At 13:30 the tone drop to G and the vibrating for almost 2 seconds. Then you primarely listening to the length of the vibrations. So as your experience, how many seconds it vibrates is the maximum to achieve before over the boundery point ? My objective is around F - F#. Thank you very much.

Thank you so much. You are a teacher.

what is the reason to curve the fret wire¿ elegant guitar by the way!.

Thank you for sharing your knowledge. For a full size classical guitar Solera the neck is lowered 2 or 1mm? The deep in the middle is 2 or 3mm? My Regards.

If adding shellac to the braces is merely cosmetic, why not add it to the back as well?

Magnetic on cleet

Hallo Ad geweldig werk wat u doet, ik restoreer gitaren bouwen doe ik niet, heb een vraag ik heb een di giorgio gitaar uit Sao Paulo brasil speciaal voor bossa nova muziek wil u vragen een nieuwe bovenblad te maken want zitten wat beschadigd in is een gitaar uit 1980 groetjes van Richard

Great video. Thanks.

Thank you for sharing this, really nice to see a craftsman at work.

Amazing video about the top and how to give the tones. Thank you so much!

not original white buttons on tuners

So nicely done

Yours sound much better. The plastic plates on the Ramirez dull the sound I think.

Very good job. You were thorough. I am about to tackle a long and a short crack on my guitar top.

Do you have any recommendations for type of hand plane to you? Angle of blade? Thanks!

Luthiers should also make voiced strings because they are the biggest contributor to the sound

Tightbond sets in 3 minutes?

How long to keep in the mold to cool the sides?

Great building and super playing. Thanks.

Fantastic Job 🎶🎸👏

Enjoy to watch whole video !! Thank you very much... I have learn much from your Video !! I am sure I can fix a top crack of my guitar.

What thickness of top do you aim for with spruce and cedar ? Thanks.

His guitar is better sounding than the Ramirez flamenco. But I have never heard his name until today. Maybe he needs to promote himself more.

Thankyou your sharing. It is very practically helpful for fretting ! on guitar ! One question is... What kind (or type) of fret you are using for classical guitar ??

Thanks Ad, I am always strugling with tape for bindings and purflings. This methode with "post elastieken" seems a good way to try.

Bravo!!! Thanks for sharing