master 🎉❤

Главное сильно держать поршень, а иначе минус палец

What do you use to freeze bolt? I have never seen this i have was always taught to heat it but if its on the car we melt everything 😢 thanks for sharing

Holz, einfach ein Stk Holz

ainda fica mais facil se deixar bem vermelho e depois colocar na agua ( choque termico ) solta bem facil .

В чем суть видео?

That thing almost took out his finger look at how close his finger was to getting mashed

Ese bro se parece a Spiderman

😅

блин ну который раз наблюдаю как наносят медную смазку на ступицу под диск тормозной.не нужно так делать пожалуйста.!прилегание должно быть идеальным без смазок и тд.где нибудь на новой машине видно смазку под тормозным диском?конечно нет.а так да видно отработан свой хлеб)

You can't put grees under breake disc!! It will damage it!!

We must have had the same journeyman

10/10 🙌

Yeah, we’ll don’t claim you are rebuilding it unless you really are….. and this ain’t.

"Careful replacement" : hammer smash 0.1s later.

how not to do LOL

Why am i seeing this video? Gen-z at it again

Why give it full air pressure off the jump? Ease into it.

Я: посмотрю-ка расслабляющие видео, отдохну от этих полических новостей. Так же эти видео:

Украинец оркам по черепам эдит. Слава Украине !

I broke my finger doing this, a painful lesson!

Thats great and all but........ The elements of road conditions will take all that crap off and all that youll find on the next pad job is brake dust....ascif you never did all that Iused to do that on the fleet, but when i got em back for next service, it was as if i never did all that. I still had to hammer the rotor off. Now i just give it a wipe with a wire brush, blow air, brake clean then give it some lube. 10 years later...........never had an issue Honestly, what youre doing is a waste of time and a gimmick for charging way too much.

Use wheel studs and cone lugs to mount the vice.

Until water goes inside

Я как то себе чуть палец так не оттяпал

BUENA TECNICA 🤷🏼‍♂️🙋‍♂️💫💫💫

Create as much flying debris as possible.

For all those who cannot seem to understand the point being made in this video. He first stuck his hand in the caliper, Then waved "no no" So he then used a pencil and 2 sockets to show the force that the piston makes when it comes out, And how it would demolish your hand

Ein groser alter lappen tut es auch

Музыки из поле чудес не хватает))

I capture it with a piece of 2x4. That will break a finger!

Медную шайбу спиздил, поставил алюминиевую!

I am a bike traveller amd my bike leaf springs is so fine it's feels like flying

People shove a shop rag there all bunched up. its safer and catched the piston with no mess

👍👍😊

Don’t shoot air into your caliper when your fingers are in there, good advice, I don’t know how you’d accomplish that anyway

Or don't give it the full 90

Totalmente TOTAL

Dalbajobs

Safety glasses !

Song toan hết😂

😂клоун🎉

The one and only time I'll accept a finger wag 😂

Thought it was Ivan at first glance

дощечки не нашлось?

Ты туда 100атмосфер подал?))))

I instinctively shouted NOOO, while watching this. Got give me PTSD!!! I hit apprentice at the back of head, because he thought that he can hold piston with his hand.

😂😂😂😂👍👍👍

High precision? This is called a toe and go, the cheapest wheel alignment option

оооо, перфорація😅 гарно гарно.