hi buddy i have the same board, but not sound at all, i changed capacitors, the amp, is working, its hot...this board uses ram sound?
@rocznik83Ай бұрын
This is great stuff. I used your troubleshooting route to repair audio on my Cabal pcb. Thank you very much for this video.
@PatrickvandenBrink-yf3wv2 ай бұрын
Great video! I recently picked up a twin in terrible condition that I’m trying to fix. I’ve got one side working but on the other side of the game won’t boot. By exchanging some boards I found out that the problem is in this bottom board for the graphics. Do you have a suggestion which part of the board might cause that the whole game won’t boot? I have no LED lighting up in the cpu with this board connected. Thanks!
@thomashoppe8933 ай бұрын
How long will it last?
@thomashoppe8933 ай бұрын
I had a rejuvenating-device, a Müter BMR-2005. On some Tubes it worked, on some not. Mostly Sony and Philipstubes are immun to this.
@pledg5 ай бұрын
Thanks for the video. I have a couple of boards with missing sprite/object data so im going to trace them back using this method.
@christophhelms49055 ай бұрын
Viel gelernt, danke!
@gorfelbt7 ай бұрын
Left unit is hard mode. Easy fix.
@jeffb66057 ай бұрын
Hello anybody home
@nilz918 ай бұрын
hizz and hum are different
@jeffb66058 ай бұрын
I would like to celebrate the one year anniversary of leaving us hanging 😢
@maxmt43258 ай бұрын
Which chips are responsible for graphics? Is there any one chip responsible for the title screen?
@renerens8 ай бұрын
The two Daytona pcbs I have in my Daytona twin have perfect 3d gfx and then all of a sudden all are gone?! And after a while they come back would this be the ram? seems strange on both of them its the same problem.
@WRKFLO9 ай бұрын
thank you
@juanmota63609 ай бұрын
this procedure reduce 30 % life of CRT, don´t do it!!!!
@horde515110 ай бұрын
Greetz! You likely have completed this video and repair already. Just leaving my contribution! - Appears the board is capable of generating the music just fine. Judge still out on digital samples although sample EPROMs are okay. The IC responsible for playing the digital samples could be at fault, or the 4558 op amps at IC97 + IC98 (Samples iirc) and IC99 (Music iirc) failed preventing consistent playback (more likely). Can verify at the source - Are the samples and music playing, but just not being amplified correctly? These are quick tests that can be checked by tapping into the outputs of the sample and music generator ICs output to something like a pair of cheap amplified desktop PC speakers. Can compare in/out of the op-amps. You can even see the music and fighting noises playing on the scope this way. Also, Great channel!
@co5972010 ай бұрын
Electronic Art
@michelecioffi182910 ай бұрын
Hallo Christoph, habe ein Double Dragon Original-Board, welches jetzt leider nicht mehr läuft. Hätte ein paar Fragen bzgl. Reparatur. Kann ich dich via Mail kontaktieren? Danke!
@michelecioffi182910 ай бұрын
Hallo Christoph, habe ein Double Dragon Original-Board, welches jetzt leider nicht mehr läuft. Hätte ein paar Fragen bzgl. Reparatur. Kann ich dich via Mail kontaktieren?
@holamanito666811 ай бұрын
thanks to brind to me this new experience
@JustPlainMcArthur11 ай бұрын
This was amazing. Thank you!
@user-qb6hd6hl4d11 ай бұрын
I have the same issue with 2 separate virtual on boards. Thank you for this video. hopefully I can get them both running, if not just 1
@ReplaceableHak Жыл бұрын
This is probably one of the most informative videos on pcb repair I have ever seen. Thanks!
@MaCJaX88 Жыл бұрын
This is one of the best arcade PCB repairs I seen. Thank you ! This should help me with my Dig Dug repair.
@drewz4625 Жыл бұрын
Well done Sir! This is becoming a lost art.
@user-vm6gy9py7s Жыл бұрын
Hallo würdest du mir das bitte machen gegen Bezahlung ?
@splugereport Жыл бұрын
These videos are wonderful, thanks!
@Megalocade Жыл бұрын
I have a bk 467 i bought it to rejuvenate my street fighter 2 cab monitor, the tube was very dim, no amount of focus adjusting would sharpen it up this was even after a full chassis rebuilt my picture pots where nearly on max, also it used to take ages to show a picture, the tube has screen burn so it has many hours under its belt, i just did a gental clean and balance to begin with the guns and the difference was unbelievable, nice sharp picture and the tube shows a picture very quickly, i did that 3 years ago and the tube has had more hours put onto it and still looking good.
@jimmygumballs4993 Жыл бұрын
It was a hint in this repair that allowed me to finally fix the synthesizer I had been struggling with for months. Thanks for all the logic troubleshooting lessons.
@fadeddeception Жыл бұрын
Hello - I did an entire cap kit on my Sanwa PM1745 C chassis with a vertical collapse and to my surprise It didn't fix the problem. Any idea where else to look? I have the twin Japanese Daytona USA and would really like to keep them. They were working fine with hundreds of hours of fun and the left monitor just tapped out.
@christophzett Жыл бұрын
Did you replace the vertical ic as well?
@fadeddeception Жыл бұрын
@@christophzett Hi - Yes, IC vertical Chip and all the caps. I have to re-check the solder points and see if I missed anything. I should have done the recapping a section at a time like you did for better trouble shooting. I want to keep this set. I have a Twin USA set also. Any ideas I would appreciate them. Thank you!
@jeffb6605 Жыл бұрын
Are you ok?
@segasega4971 Жыл бұрын
I've got a nightmare one of these with a sound issue. No attract screen music, but plays when game started with missing samples, ie: No sound when hitting opponents. All 3 sound eproms verify ok. Volume works ok.
@joshgreen6740 Жыл бұрын
Can I pay you to repair mine?
@splugereport Жыл бұрын
Super awesome to learn your logic on these. Wish me luck on these seattle boards :)
@davays Жыл бұрын
Would anyone know why my boot logo is half missing and characters are also missing. I have tried the options in this video with no luck
@onjisan Жыл бұрын
Where have you been man! Come back to us
@casselfornia186 Жыл бұрын
Well done. I love your Videos. If you ever want to try to fix my Sega X Board Super Thunder Blade PCB let me know. It has trouble with the sub CPU and unfortunately I am at the end of what I can do. I already asked a few guys but everyone keeps a distance from that PCB. My DX cab would be happy ;)
@marlabedenbaugh1619 Жыл бұрын
I am SOOOOO excited about your AMAZING video. This is the exact problem with myDaytonnnnaaaa! All of my new chips have come in, and my programmer. I cannot find the suggested link to burn the file. PLEASE rescue me.. you’ve gotten me this far.
@renerens Жыл бұрын
Great Channel! You deserve a lot more subs!
@marcfrets Жыл бұрын
Hi Doktorzett, I'm wondering if I can ask you a quick question since you have a working Phoenix PCB. In my repair on the CPU board, does your pin 11 wiggle on IC34? Mine is not and thus the two flip flops I suspect at IC37 are not doing much. In my case its stuck high coming out of IC34 and I want to confirm that its not the correct behavior. Is that correct? Should pin 11 be wiggling to have the flip flops be activated? Having real challenges getting a stable sync signal just to show garbage. I removed the CPU to take it out of the equation just to get this far. thanks so much for your help!
@splugereport Жыл бұрын
Enjoyed this, thanks!
@nathanrochester Жыл бұрын
still learn from your videos fixing my own double dragon
@3vi1J Жыл бұрын
Just stumbled across your channel while browsing related videos on my subscribed retro-hardware channels. I *love* the detail you go into while troubleshooting this. This was extremely educational and I appreciate you sharing your experience with us. I remember playing Phoenix and Pleides back in the day, and I always wondered how similar they were under the hood - very similar, apparently! Thanks for the great vid! Subscribing and checking out your others now.
@nathanrochester Жыл бұрын
mouse piss is what causes problems and having the pcb on the bottom of the cabinet. makes a good home for mouse lol
@marcfrets Жыл бұрын
Howdy - I’ve been following your repair videos closely. I really appreciate the detail you spend to explain things. You’ve inspired me and I’m currently attempting my own phoenix pcb repair. I wanted to ask if you could consider a video where you talk about changes that were made to the board such as jumper wires and such. The one I’m working on now has jumpers added, caps soldered to ic legs and other weirdness. Would love to see your approach to debugging why those types of changes were made, whether you try to go back to original board configuration, or other thoughts on this matter. Keep up the great work on these videos though!
@tonye4176 Жыл бұрын
If it were always that easy haha
@lonewolf3112 Жыл бұрын
I need help on mine Jamma board the screen is upside down , how I fix this?? 🤔