Great information will follow your advice 1999 f150 4.6l v8

Come on man. Please stop telling people this crap works. ESPECIALLY the pour-in kind. At the very least you’re going to clog up the thermostat but also the radiator. The chemical sealed kind where you drain the radiator and take out the thermostat, it’s possible to have a temporary fix. Trust me, I know. I have a leaking head gasket on a 2009 frontier and I’ve tried everything. But at some point, you have to face the fact that it’s too expensive to fix the head gasket. The only option is to buy another motor. It’s painful, but it’s just a fact.

Thanks for the help and for the time to upload this video. Thanks once again 🙏

What does this stuff do to the water pump, heating core and temperature sensors? When the gasket goes bad....It is time to open your wallet wide.

When you say drain your system do you mean drain the gas, the coolant and the oil? Do you mean power flush the radiator? Drain the gas and use Heat to get rid of the water? Let the engine sit before draining the oil so the water comes to rest on the bottom?

Just bought one today, interstate load runner that is.

yoo wsp man! my wii bluetooth or wifi adapter is loose (this is unrelated)

I just bought the interstate Loadrunner , came with vents and a lot of extras, love it

Glad to see you're still up & about! Miss being in your classes

Great video

Great video, straight and to the point with no filler.

I am canceling my Bars Leak purchase.

"Spinny clip thing?" Really?

Well you are the first with engine problems with a Toyota, for the most part your car should last 200K.So thank for the heads up, good luck............BB

If I could I would post a pic of how well this crap, the CRC green bottle , sealed my whole radiator and cost me thousands. Get it fixed right

buen comentario- pero hablas muy lijero y los subtitulos se van antes de que temine de leerlos

thx man, appreciate it!

2weeks later ..still driving with the Barrs headgastet formula .don't go over 50mpg

I purchased the fc3 and Fc8 from Amazon. The fc3 works fine. The fc8 failed first test when I slowly poured a small amount of water through it. I sent it back as it was faulty. Another thing, you should only fill with fuel half way up the filter otherwise the pressure forces water through.

Nice

Wonder if the stea setting on an iron would be better to moisten.... Or even holding it bov boiling water??

Seems like an ID 10 T error

Did you ever figure this out? I’m having the same issue and can’t find anything

Sounds like a warped head rather than a blown gasket. I used Bars Leaks on a 600 hp Buick big block. It took 5 thermocycles (heat up and cool down) but it did work. It's a race car so I don't have many miles on it and don't know how it will perform over time but it cured the problem for a lot less work than me tearing the motor down to replace gasket

The answer is Simple... Don't let people fuck with your Shit 😂 🎣🤙

I wish I had tried one of these before giving my Honda back

Yeah this looks like a clutch dog issue

kzfaq.info/get/bejne/bdFonJhmxKeYn3k.htmlfeature=shared

Thank you!

This should have tons more views!!! Informative display, hillarious commentary! Thanks for the content keep it up

and.....tHank you very much ! Very well presented findings !

I drive old cars and trucks. K Seal is my go to in these situations. Working so far!

The walker downrigger swivel bases here have the nylon and stainless washer under the head of the nut, not under the bearing channel. Which is correct? Mine have nothing under the lower channel underneath the 3 washers. They work fine..

If you switch ink colors or wait some time in between printing, do you somehow wash off the ink on the slice with just water or oil?

You have done something wrong. I don’t know what. But I have been using mine for 4 seasons. Works perfectly every time

Thank you for this info...

What kind of ink?

Thanks for the help!

Give you a like. Thank you for the review. I need one ASAP before the Gap gets bigger on my head gasket. I'm glad you're over a thousand subscribers. Keep posting

Thank you

How do you get all the wrinkles out of the paper?

Excelelnt , thanks alot , very helpful !

Awesomeness 😎

Yikes. Too much blade extension on that Olfa! Normally scoring one side is enough. Clean up with back edge of Olfa.

Bar’s leak doesn’t work especially when you go over 60mph

What thickness is this?

This reminds me of when mackgyver used an egg to seal readiater leak.

‘07 4Runner leaking head gasket and hole in the radiator, to fix it cost more than the vehicle is worth, K-SEAL Pour-n-go , I just dumped it in the coolant at operating temperature and put the cap back on, 30 seconds hole plugged, HG sealed, I let it flow through the whole system, heater core, and all did not plug up anything, they tell you to dump it in cold for safety reasons, but it works better imo if you dump it in hot and you didn’t hear that from me😮 6 mo. & 4500 mi later nothing to see here

Blue devil works you have to flush the motor first. I tried bars leaks didn't work . Blue devil turns hard and fills gaps when it's exposed to hot areas from exhaust leaking in the heads

I am just getting into planer boards, while watching your video my wife over heard you say you had rocky spotted fever and she has a client that had it and helped her with her arthritis. Do you mind if she sends you some information that mat help you. On another note, would you suggest tx12 or tx22 planer boards for walley? Thanks for any info