I have a 2011 Jeep Grand Cherokee Laredo with the 5.7 hemi. Bought it last summer and ac quit a week after taking it off the lot. Reads high with the gauge so I know it's got refrigerant in it. Clutch doesn't engage at all with the ac on. Spins freely by hand, not real easy freely but turns by hand with minimal strength. Fuses and relays are good. No noises at all from anything. Any ideas?

Who the hell doesn't know this

Wow yours came with instruction

Thank you so much for posting this you save me a whole bunch of headache!!

Warning!!! If you have any problems with your jackery and want to return it for a refund you will be charged a $110. Restocking fee

Driving through life clueless about this.😢

You shitn me😂

How many trips to the parts store did it take??😁😁👍

No iron and steel. All plastic.

How come every one of these videos that show replacing the sensor, it is always the left rear wheel?? My left rear is also not reading. Is it because that is the side the exhaust is on?

Thanks

This is amazing. I dont have one of those 90 degree impact wrenches (yet) but I could get one that handles 45, 55 or 180 ft lbs of torque. Do you think the 45 would get this done??

Take the top light portion off the main tube and you can unclip the battery and pull it out from the top

Mayhew?

I have a 2017 jk my ABS and Traction Control light turn on a few seconds after turning on the car then about half a minute or so it goes away, all my seals and hubs seems ok i just got the front Axle seals done, my guess is a faulty sensor.

The screwdrivers are assembled in the U.S.A.

try with distilled water and ditch the glass jar and expose the bolts

Best video hands down. Thank you!!

I just put together my dash they airbag light came on Only the passenger side then I disconnected some wires that went to the old phone in the fuse panel. The third one up on the passenger side door fuse panel. Was the one that I had to take out to disconnect this wiring for that phone thing any Ideas on how to fix it or Do you think the module could went bed

If this bothers you look into New Age Industries. They sell 100% virgin US Made Chemours Viton fuel hose through the U.S Plastic webshop catalog

Can it clean jewelry?

The bright white light of LED's is certainly worth it. I've had the privy Truck Lights on my XJ for the last 5 years and I'm still very pleased

What website did you find it at ?

Thanks for the video. My son did this step by step. Worked great for a few weeks. Then it happened all over again. What did we do wrong?

That is pretty cool. I can definitely see that coming in very handy. I used to use lacquer thinner to clean my bolts from machinery.

The bolts were not impressive but the EGR valve, wow,

Told me state inspection couldn’t replace the damaged windshield wipers I had legally? So I had to do it myself, looked up how and found this video which helped me replace them in minutes! Video helped me July 5, 2024

My guess, this is pretty much ALL ac clutches??? I am going to check mine. I damaged/killed my condenser with a power washer, (idiot) anyway, clutch turns, not locked up, and will check power and then your trick. Thank you for this video. Bravo!

pretty coming on those nissan it happen to me 2 time before

Pull the e clip. Wd40 on the shaft and that boot slides on easy. This is a huge waste of time and energy.

Just happened to my jeep this weekend while in the bush. Ended up in Neutral unable to get out. Fortunately a few hours later managed to manually move the shaft under the vehicle. Jeep know this is a problem and could cost some a lot of money in towing fees. Something so simple made of shit.

Groovy fix

Im a big fan of the little fan. I use the small one in my roof top tent. I have a v20 knock off craftsman 9ah battery that lasts me over a week of nights camping. Love it

Exelent video thank you sir!

What if my clutch is making a bunch of noise and is ready to seize up?

Buy some cheap toothpaste with baking soda in it. Little bit on a damp cloth and polish those things. Works like a charm.

U suck

"The sound is kind of Japanese" that was funny 😂😂😂

well well well, look who it is! You helped me out on this one

Not groovy!

So is it for cooking or heat?

Lots of bent frame hard bodies here in French Town.

The piston did not clean itself.....

Hardbody my beloved

Yes its done.

That's what happened to me, I just kept adding oil 😂

What do you mean was this head gasket blown? Obviously it was blown, you even said it was blown as you showed where it was blown.

Haven’t seen a hardbody on the road for years. Yup that’s a blown head gasket.

You had high pressure in your coolant and possibly ring blow-by mixing oil and coolant 🧐

Didn’t work what’s the next step ?