motion detector?

Hello is there any possibility to recieve a DVB-T signal? I mean is it possible to watching a TV with this set in your video? If it is, would you tell me how to do it? Thanks!

Anyone else have problems soldering those little boards? Can't see shit

More of a mod than a hack

I think in the modern IOT world, these things are effectively obsolete. You have smart bulbs and mmWave sensors for a better result and you never have to faff around with mains electricity.

Empfindlichkeit hoch/niedrig = Sensitivity high/low

Interesting in that they used a relay as opposed to an SCR.

Achtung

I got once got a solar kit very similar to this one and the only things I kept were the solar panel and motor so I could use them for other things. Also did a similar thing with other science kits where I would purge them for items that I found useful for my other hobbies.

I loved the old ones. Only had to swap it once. The new rebranding, I swapped constant times. Now I have no warranty and conveniently the multifunction button fell off.

These have been out for years. It's a good toy and a nice size. As a sparky, an electric screwdriver is nice. Wihas is amazing but 300$

Do you have a starter replacement post?

Do you still have the instructions from dada? They are no longer trading, and I just want to do some upgrades on a broken quad 33. They used to be freely available on their website, but unfortunately that also doesn’t function. Many thanks.

This video is just an excuse their cameras are extremely slow it takes 21 seconds to load, I've reset my blink module I upgraded my router nothing changes the speed

Is the PCB Green layer a Protection layer what if its a little bit scratch won't go farther than the Large area Been scratch ..some sort ..🎉..?.

Tip, when you’ve drilled your hole, don’t check for sharp bits and shards with your fingers like you did 😂

Just to mention one thing, the bits aren’t pozi as you said, they are Phillips (ph), other than that good video, 🤙🏼

I bought one of these with about 40 bits and came in a proper carry case. Had it about a year and has been rock solid for the price of around £35.

Since the (SMA->ipex) feeder plays a role in the setup and the monopole antenna is ground plane dependent,use a SMA->ipex adapter attached to S11 port,plug the feeder there and calibrate the VNA at the SMA end of the feeder.Then attach the antenna there to tune it.For 868 Mhz a 1mm enamel copper wire with 9 turns winded in a 3.5mm drill did the job.Also the distance of the first coil from where the sma ground ends is important and it's 9mm

Thank you for all the instructions, but i can hear a hiss can you advise where to put dcdc filter.

You should use a punch and hammer to punch where the hole should be drilled, that way the drill won't slip and drill somewhere else on the board

gonna use mine with my Sprectravox & mic for some low bit goodness

Thank you so much for fast reply! Main problem must be heat, we had a headwave last week with 46 degrees C and since then wipers went off. I'm afraid that used ones here in Cyprus will be same or even worst. Thanks again.

My wipers stopped working, the mechanic told me that the control stalk needs replacement, do you think that i could easily fix this by myself?

Hey everyone! Just a heads-up about working with epoxy resin. You’ve got two types: the two-part epoxy doesn’t need any UV light to set. It’s pretty neat - you mix the resin with a hardener, and they start to solidify all on their own through a chemical reaction. Give it a few hours, and it’ll be all set, no UV light needed. Now, for the one-part resin, that’s where UV light comes into play. If you’re using this kind, you’ll need a decent UV (or sometimes LED) light to get it to cure properly. The little light you might have at home might not cut it, so check the bottle for the recommended wattage. Oh, and about hydroxyethyl methacrylate (HEMA) - great job on the pronunciation, by the way - it’s in both types of resin. It helps the final product stay dry, adhere well, and keep its strength once mixed. So, if you’re experimenting at home with two-part resin, remember to mix equal parts of both. No need for a light, but patience is key as it takes a while to cure. On the flip side, if you’re using one-part UV resin, you’ll likely need a 65W light, but the payoff is it cures super fast, like in 30 seconds! I personally find the one-part UV resin a bit easier, especially if you’re just starting out. Plus, you can have fun with any leftovers.

Miley Cyrus Hannah Montana

I bought one from Temu and it doesn't spin when i blow in it

Thank you, my unit had the exact same problem. I put a new screw in too and it works fine now. Thank you for the video.

What an awesome idea.... Brilliant thanks 👍

Thanks Andrew, ive got one of these devices, its an older one and ive struggled to work it.... You have just shown me how to use it now. Brilliant 👍

Let’s hope this works

100wt bulb driver giving out low voltage , can capacitor cause it

Hi, great video! Where is the Amazon link for the motor?

Would have been nice to hear some musical clips with singing than talking through the whole video. Couldn't even tell what they really sounded like.

I bought a tens machine from aldi for $40 I love it so i decided to get another so both the wife and myself can use them, I got the same unit as yours from ebay and its terrible it just hurts. Maybe its the cheap gel pads i dont know but i dont recommend it

Too long , too much talk.

this is going in my alarm clock i just bought

Hi there, I think you`ve made a great job..........can you help to bypass Zero SRF 2019 immobiliser ......I will be grateful Sir

The pins are screwed into the cap. So remove pins first using needle nose pliers and twisting them to remove.

Gggy

The internal LCD is just the screen correct? If so then it can be fixed. Getting my BF’s father to help fix it.

1:45 - You stated that you cannot change those particular capacitors, why? Are they part of the board, or are you just saying you don't have the parts to do so?

Please play the demo I've forgotten !

Where did you buy the phone?

Absolutely not.

Is it podsible to get 240p 15khz over this adapter?

Great attempt and great video. I am currently struggling with a Phasar 2000 that was working but now that I finished polishing the case the module now resets back to 1:00 after I am done setting the time and date. I am guessing the grease i put in the wall of the pushers is causing the issue, but I am not certain

Mine broke after less than a year, in the same spot, but the design of mine looks different inside. There's no exposed titanium in the band, but rather a plastic end that is supposed to lock to two pins embedded in the end of the headphone section. The strange thing was that the plastic where the pins were embedded was completely crumbling away, as if there was something wrong with its composition. In any case Shockz was good about warrantying this pair.

can you make an update video with liks to the object that you used

😂😂😂 better this way. take a moto and a mirror and a laser pointer. tge laser will be stationary and will hit the mirror. a motor will make the mirror to move up and down . so the mirror move will have the shape o signal. the driver will take the input and the murror will bounce the laser into mirror who will reflect it to a wall. niw yiu will need just a camera of a phone and a soft who can mive the image to the left . on the phone screen will be laser at all the points in time