KRT Frameworks & 46works are my therapeutic channels to go to.
@jorgemercatali9319Ай бұрын
Beautifull
@BenLeeBlАй бұрын
Shots 100% editing skills 20%
@christophermikrowelle7093Ай бұрын
Klasse.
@kevinlewis91512 ай бұрын
If I was going through this much trouble and precision, I would go ahead and seal it all up and pressureize it and use the frame for gas storage.
@kevinlewis91512 ай бұрын
Ok you've taken what used to be simple cut and weld to fit and turned it into precision craftsmanship. Im not sure its a good thing, but your definitely an artist.
@danielver44842 ай бұрын
I beg you to use only one recommendation -eye protection. This will ensure that you can serve your customers for many years to come. Thank you.
@Ezequiel-ps6bv2 ай бұрын
Se extrañan los videos de este canal,😢 alguien sabe que paso ???
@blackdiesel44072 ай бұрын
Is this an elgi replica?
@Linhe1392 ай бұрын
What kind of aluminum is this?
@stagweekenders25282 ай бұрын
Amazing work. Old enough and wise enough now to wish I could've learnt all this - result of a misspent youth. Even at 54 though, I'd seriously consider an unpaid job at your place to learn those skills!
@georgebest19842 ай бұрын
Nice work complete change. Do make the riding seat lower? Thank you
@HiluxV62 ай бұрын
Sounds better if you have two separate.left and right
@sinocaig2 ай бұрын
Work of art dude. Would have love to see the sewing portion...vid for that?
@ginohoffmann60322 ай бұрын
einfach genial dieser Mann !!! ..ich wünschte es gäbe jemanden, welcher für meine Magni MV Honda auch so ein Paar Seitendeckel herstellen könnte !!!
@timothybrockbank74743 ай бұрын
Beautiful work of art
@RalfPfister3 ай бұрын
sieht toll aus.
@Levente203 ай бұрын
Do you have to disconnect the battery before installing?
@Terandolus3 ай бұрын
Absurd. Vor allem die schönen TIG-Schweißnähte. Unglaublich.
@jaguarchua3 ай бұрын
I like the look of it but I wonder if the rider suffers from accidental burns since its located near the seats
@michalolsansky21723 ай бұрын
excelent works, but what is the foam and density? thanks you :)
@hgm83373 ай бұрын
I have to say your products kick-ass
@AZ-qn3xq3 ай бұрын
Amazing work my friend!
@Vilhyto3 ай бұрын
Amazing craftmanship and very cool workshop but, please, use eye protecting glasses when gring etc.
@hgm83373 ай бұрын
in other words a 'shortel' :)
@davidcarr44643 ай бұрын
Awesome work. Did you powder coat that in clear?
@iamandreja3 ай бұрын
Superawesome! I enjoyed both videos, very helpful and satisfying to watch. You're using some techniques I wasn't aware of. I am curious if the logo from which you removed the coating will rust.
@DouglasSonders3 ай бұрын
do you have a 3D printing site where you share tools you use? love your channel
@hgm83373 ай бұрын
Could you post more pics of the finished article for us mere mortals pls?
@hgm83373 ай бұрын
mad fab skills,... pls keep posting and delivering more parts to us mere mortals
@HaroonAmad3 ай бұрын
Cool
@jailynoftana3 ай бұрын
Magkano po..
@jailynoftana3 ай бұрын
Magkano yung pagawa nang chasis nang motor wave 125 stainless .
@cyblade8883 ай бұрын
I bought this set for my 2015 roadster, but I'm having some issues. In this video you specifically write 'Scrambler', but on your website and ClassicBike you don't specify a model. Well, the installation of the bracket on the Roadster forks encounters space limitations. I tried with the lowest position, but I think the problem is the same with the highest position too. The vertical brackets of the bracket hit the bottom plate of the forks, causing the headlight to remain pointed too low. I believe that the solution is to build spacers of even just 1 cm to place between the bracket plate and the attachment point of the motorbike.
@KRTframework3 ай бұрын
You can select the version in our store ( Euro 3 and Euro 4 ) and your model, the Roadster ( upside down fork ) and the Racer have a bracket with which the headlight sits a little further in front of the fork. In the highest setting, however, it should also work with the Roadster ( not with the Racer ) But feel free to send us an email ( [email protected] )
@cyblade8883 ай бұрын
@@KRTframework ok thanks, i send you an email
@iqbalalfayed96474 ай бұрын
excuse me what size was the new headlamp?
@hgm83374 ай бұрын
Will this subframe be strong enough to take a passenger? Will it allow the conventional seat / seat hump / passenger seat for the RnineT roadster?
@user-ro3zi8nu6z4 ай бұрын
¡Hermosos!, wow
@Avantone4 ай бұрын
Wow. Just Wow!
@ScooterandJobe4 ай бұрын
Hi. Great work. What grade//thickness of aluminium are you using?
@youcanfoolmeonce4 ай бұрын
I wonder if this fantastic part can be mass produced, say, from cast aluminum? You could make out loke a bandit, selling it to R9T owners who acquired good taste.
@pomdejesus81504 ай бұрын
what steel material are you using?
@cliveblacksheep25225 ай бұрын
Nice work
@tomchristensen33925 ай бұрын
Craftsmanship
@johnvanoorschot5635 ай бұрын
WAUW!
@user-ux8be1ee1r5 ай бұрын
Brother were you can get that machine.
@user-ux8be1ee1r5 ай бұрын
Very nace
@Toddtesla85 ай бұрын
FUCKING THANK YOU FOR THIS VID!!! FOREVER CHANGING MY LIFE!!!!
@DoudouFarmer5 ай бұрын
Oh nice job man! Where does the 950 Rally kit come from?