Thanks you for delving into this. I am experimenting with a VESC controller in regeneration mode to generate electricity from a BLDC driven by an engine. This generated power is then fed in parallel to a battery and a load. The VESC allows regen amperage to be controlled, but not voltage. I struggle to understand how not to blow up my battery and how to control the voltage. Does the PWM control for the lower MOSFETS change the voltage or amperage output? If only amps, how could one limit the output voltage?

It's shocking

i got one of these kt compatible foc controller .. 36v and only works with g51 screen .... it doesnt work with scooter motors ... only geard motors of ev bikes ... can i reprogram it to make it work with scooter motors?

Hello I have KT controller 12 mosfet 48/52 v 35A can i increase the AMP by using software you have used? i just would like to increase it to 40A

Hi Shaun, thanks for you very informative video. Might you know where I could find that manual or guide for taking the lens off? Would really love to see. I'm worries about the levers you spoke about..

I.hate back.boilers. I prefer combi boilers. Easier to get to.

hello sir phev battery how much cycles ?

Damn... those magnets are huge!!! What a pitty... imagine those in a brushless config...

that is the coolest thing ever! How you do it ?

Thank you for this, I didn't know what the hard boot connection was for, and my 72v kunray was doing the slow startup thing. Appreciate it!

This is awesome. Please keep us updated

Hello, good afternoon. Sorry for writing here I have a question about a Scopic canon, can you give me some advice?

i love the use of the glands to support the entry points . Could not find your tutorial and measurements you used.

Is possible Parma Natale disconnect plug in Hybrid system no need more charging?

What was the fan fault?

look forward to seeing more from this project!! very cool

Interesting, thanks for making your videos! I'd think the steppers would do just fine as they are. They can be driven to one extreme every start up to find reference and should very unlikely lose any steps if not driven too fast.

Awesome video. Underrated channel. Been watchin a long time keep it up man! 🙏🏻✌🏻

It can work sensorless!?

Thanks for sharing. Can the filter be taken out for a clean?

What wire are you hooking the hard boot up to

For anyone watching this video: the Cells are GS Yuasa LEV46 cells. They're 171x34x108 (mm), 2.75v-4.1v (3.75 nom), 46Ah, 200A max both ways and weigh 1.40kg a piece. More info can be found on their website.

Hello Shaun, Could you please do a video about how you tore of the bottom part? Is it only held on by gule or is there some sort of compound?

I can’t comment

Maybe I'm wrong, but sounds like that alu block is done. Don't think they handle overheat like cast iron, wonder did the head expand and pull the bolts hard enough to warp the block lower down. Would a small diesel not be a better fit? Maybe liquid cooled 2cyl in a soundproof box?

Are you running this on propane or petrol? If you're running on LPG maybe your pressure regulator cant keep up. The other point is that the engine running on LPG will be considerably hotter than running on petrol, especially in WOT situation. Maybe that could contribute to blown head gasket. Kepp up the good work, I enyoj your content very much.

In air-cooled engines a drop in power is very common as the engine heats up. A drop of 50% indicates to me that the engine was close to seizing up. This could be due to lack of oil circulation or just straight overheating. The hone will not take out or correct a distorted barrel. Unless it is wear in a longitudinal (wear at the top or bottom of barrel. I would be replacing the barrel as well as the head.. if not the whole engine. Using ZX1 in the oil will dramatically reduce the heat generated inside the engine from friction. However, that engine is basically toast.

Are you using this for a biodigester or a paraglider?

Loss of power could be a fuel issue. If you have a thermal imaging camera or it temp gun see if the temps change when it loses power. It could be running lean.

Thanks for the video, really looking forward forward to more updates!

I've had one of these scanners that has been working very well. But suddenly this evening I'm getting a strange black artefact on every single scan of negatives. Half way up one of the short sides, it looks a bit like a spider half sticking out into the frame. Not large, in total maybe a millimetre or two into the negative area. It's there on every single scan. Same place, exactly same shape, same size. It doesn't matter which frame in the carrier I'm scanning, it's always there, so can't be something on the carrier or a particular negative. It isn't regular like a line across / down the frame, so doesn't look as though it could be something on the sensor / mirror / light source as those just move in a straight line across the frame. I've had the cover off and can't see anything inside that would account for it. And I've tried compressed air to try to clear anything. But no effect. Still exactly the same artefact in exactly the same place every time. The fact that it comes out as black on negative scans suggests that some pattern of extra light is reaching the sensor (rather than light being blocked) - if I swap to a positive scan it comes out the same shape, but light. Any ideas?

When i go another video and types comment and disappeared too they same to me Thank you❤

Happens to me all the time.

My 2020 i3s has same issue now, heater started working only intermittently and now completely no go. Be great if you can post an update

Hi @ShaunDobbie ,can you please tell me how to run this compressor on a quadcopter esc?I have bought one without a controller attached and too expensive and not avaialble easilyin south africa.I would really appreciate if you could get back to me,iv searched high and low and you seem to be the only person who has made a video regarding powering the bd35f without its original controller.Thanks

Why removing cells from casing? Decreasing size? How will they be repurposed and arranged? Have you made a video showing those built? Seen them on your bike video charging with welder but not from inside

Cheers …👍👍🚀🚀🥁🥁

Just having a watch as I'm thinking of getting this kit and mate, your tub of swarfega is giving me PTSD flashbacks from when I was a mechanic. 😂

That was really helpful to show how the boiler actually works, thanks

I would just nip to my local Scrap Merchant for some lead pipe. Melt it in a pot to skim the impurities off, before using it.

Make sure those caps are FULLY discharged before inserting them into the molten conductive metal.....

Sorry don't believe it

This same thing happens in mine! Thanks for the video!

Can you hook up a display i got one for ebike i think i might have messed up 😢

Looks very useful!

Anyone this year

Hi Shaun, what year is your car? I'm trying to find that fuse.

hiu

Hi