These saws usually need to be sharpened as I believe they don't come sharpened

You may want to consider thinning down the handle. You might observe some significant improvement in the handling of this awesome axe.

Watched it. Very interesting. Will keep practising

Do you have any info reference to stop start system fault battery seems ok and alternator is kicking out 14.7 v so charging ok

thats a big head but ur doing it wrong watch skillcults video on chopping and also blade is supposed to drive at least an inch each swing

It's very easy to move your hand away from the draining oil . Also, after you've changed the fuel filter, cycle the ignition key on and off several times without starting the engine to activate the fuel pump and fill up the new Filter. Alternatively , use a vacuum pump to suck fuel in the return valve for the same purpose.

Correction. The steel is 5160 steel. Not sure where I got 1081 steel from.

I do not split I cut it in half burn it vertically i have an American maul that would out split that all day long cost under ten bucks I know they saw you comming for the price of that item i had two old Craftsman large and small for a quarter of the handle s price !

You can use a bicycle cable on a drill, it takes a bit of time but it can be done and then clear the faults. Job done!

Misleading terminology, its the turbo upstream pressure sensor. The differential pressure sensor for the DPF is not visible and is behind the engine connected to 2 rubber pipes

We used to drill nearest across the flats size Alan key to suitable drill and achieve the same result in our tool room. No need to buy special kit.

What is the name of that tool and where van is buy it

Hi, does it take 4.6l of oil as stated in the service book or less than that?

I'm also not sure if it's fully waterproof ?

It is making a clicking noise so I think the transmission needs a shim. Other than that, perfect

Some nice shots and a great location! Any issues with the rig? I have one & it's been bang on

Stock waterproof?

I like. Thank you

I trail long distances so changed the ESC to F/B/R with the jumper. The drag brake is far weaker this way allowing for 'free wheeling' and increases runtime significantly. I use high gear, unlocked front & rear, and change to suit terrain. Amazing truck, enjoy!

Just got one of these, they all click depending on which gear is selected. After greasing the diffs it's a bit quieter, it's all metal so naturally a bit noisy

Watched this to see how the anti roll bar is removed as per description but ended up watching how to remove the anti roll bar links which I already knew.

I will take it out again today and check. Would a clicking noise mean some teeth are damaged?

What’s that clicking noise?

Nice Axe picked one up today 👍

That's not the anti roll bar it's the drop link

cheers for this mat

Oh, my! Saw horse used wrong. One-handed operation that could lead to you havong a big gash in your head and your wife and children having to feed you and change your nappy for the rest of your life. That saw was up to that task with 12 inch bar but you weren't so you put a 16 inch one in its place, why? A longer bar never makes a chainsaw better but an op who grows her/his skills gets more work done and does it safely

I bought new chainsaw bar few months ago for my ms 180.I clean her uo...start chek lubrication cuts like butter

Most people in here he's not a pro . I think he did a great job frist of all for even tryin it and he got it done complete under pressure hats off to you

Why not use hardwall?

You just showed everyone the most dangerous chainsaw operations video I've ever seen! You should NEVER-EVER operate a chainsaw one handed, if you would of had any kickback you would most likely be dead now!! Please don't ever do that again!

Hey man. You are using your saw horse wrong. No wonder that little saw bogs down. You’re pinching your blade with physics and gravity.😂

This was so helpful! My girlfriend and I have just purchased our first home! only issue is this has happened to the entire house 🤣 So we now have to re-render and plaster the entire thing. None of us know how to render or plaster lmao ! Its going to be a challenge as we need to learn as we do it! I'd say only 5% of the house has the render still stuck to the brickwork. absolute nightmare! but we are taking this opportunity to do an full house damp course.

cool vid god info

So take it to the garage then lol 😂😂😂

You even matched the wall color so perfectly. Amazing!

Just a small note - it's not the anti roll bar that's been changed here, but rather the anti roll bar end link. Changing the anti roll bar itself on this vehicle requires lowering the subframe, which is joyful. :')

For a DIY job you did good! I’ve seen much worse by ‘professionals’. Next time draw a square around the damaged area and score the plaster or use a multi tool to cut around the area. When you remove the blown plaster it won’t disturb the plaster you want to keep.

I had this symbol come up but it went away after 5 mins of driving. In my user manual however it says it’s either front radar obstructed or issue with lane departure warning, traffic sign recognition or toward emergency braking system ? The latter all related to front radar ??

How not to guide 😂

Plaster ot same day whrn the pva is tacky

Mate you need to prime bonding if your doing it next day you made your life hard there did the plaster not craze with it drying too quick next time plaster wall same day will give you plenty time to play with it

The dry plaster did make me chuckle 😂😂😂😂

The dry plaster did make me chuckle 😂😂😂😂

Where do you get the removal tool from?

What year is the car?

The result is what counts and it looks well, good little project.

what engine is in this qashqai?

Thanks🎉

Looool 2 day job ??????? Yeeehaaa