Steven Taylor

Пікірлер

@willtricks9432 4 күн бұрын

I won't say you're doing it wrong but your holding the Chainsaw in the best way to cut your head off if it kicks back. Serious question, are you left handed? Right hand on the throttle and the bar should be right over on your right side. I like your channel and Subscribed so I don't want you to lose an arm or something more vital as I would miss your content. Been swinging a chainsaw for 35 years so I do know better. Cheers for the vid.

@StevenRobertTaylor 3 күн бұрын

Hi, yes I am indeed left handed so this felt comfortable enough. I have a good grip strength and had afew kick backs which were ok so I'm not concerned. The chain brake also working well. Thanks for watching!

@T4yyib11 4 күн бұрын

What thickness sheet metal did you use to patch the inside wheel arches 1.2mm with 0.6wire ?

@StevenRobertTaylor 4 күн бұрын

@@T4yyib11 Hi, yeh 1mm or 1.2 with 0.8mm wire. Just the way my welder was set up. Thanks for watching!

@kevinstuarttrainor3927 6 күн бұрын

Where did you find the Jaos?

@StevenRobertTaylor 6 күн бұрын

@@kevinstuarttrainor3927 actually found it on marketplace fairly locally. But never seen one again, fairly rare here

@sjh0010 11 күн бұрын

Constant flopocity joint

@StevenRobertTaylor 11 күн бұрын

You could say that yes 😅

@karhukivi 21 күн бұрын

I am going to try bypassing the thermostat as no power seems to be reaching the burner unit - thank you!

@StevenRobertTaylor 21 күн бұрын

Please only do this for diagnostics. You 100% cannot run your system with no thermostat.

@Mr75044 22 күн бұрын

Bought a bandit 600 Brand new in 1995. Used it quite a lot. After 17 bikes & 15 years. I was shocked as after It was left in the garage for a while it wouldn't start. Had to recut the valves back in as they wouldn't seat. Very strange. Shame as there was nothing about the bike I didn't like.

@ezyjamez7451 23 күн бұрын

What battery do you reccomend the gel one or the lithium one? Got the same model myself.

@StevenRobertTaylor 23 күн бұрын

Hi, a normal gel one would be sufficient. This isn't a big engine to crank over. Thanks for watching!

@paulsteele8614 29 күн бұрын

Yup its out of gas

@StevenRobertTaylor 29 күн бұрын

Itl take more than a fresh tank to fix 🤣

@Rickster621 Ай бұрын

It will buff.

@StevenRobertTaylor Ай бұрын

That's what I'm hoping! That and some thicker oil should sort it right out

@kevinspalding5470 Ай бұрын

Got a bit of a job on there !...

@StevenRobertTaylor Ай бұрын

@@kevinspalding5470 the job is throwing it in the scrap, it's a two piston compressor pump.

@vikingdrummer9140 Ай бұрын

you are a very clever hands on man well done job

@StevenRobertTaylor Ай бұрын

Thanks mate! Always working at something 🤣

@vikingdrummer9140 Ай бұрын

top job got the same pajero . for light surface rust i use aquasteel with my spray gun no need for nasty underseal

@StevenRobertTaylor Ай бұрын

Hi, thanks, I actually have it back on lift now doing afew other areas. That aquasteel sounds good il give it a look. Do you just spray it on with a paint sprayer for compressor? Thanks for watching!

@vikingdrummer9140 Ай бұрын

@@StevenRobertTaylor yes with compressor i use 2lts a bit over the top lol but just redone it after 4 years was when i did it last time not cheep but works realy well thanks for the vids bruv

@StevenRobertTaylor Ай бұрын

@@vikingdrummer9140 I'm not in a panic to get this done so I think I will take your advise and lash some of that stuff on before I coat with gravitex. It's bound to be better than doing nothing at all.

@vikingdrummer9140 Ай бұрын

@@StevenRobertTaylor mate i never underseal that stuff no need to and over 24 hours gives a lovely black finish to it sorry if ever my spelling is bad am crap at it am old school had 40 years on spanners just do family cars now but you realy are very good at what your doing all the best mate

@StevenRobertTaylor Ай бұрын

@@vikingdrummer9140 Thanks! That's good to know about the aquasteel. I have the gravitex there sitting ready anyway. It will need something to blend all the patches in properly.

@iainahastie8658 Ай бұрын

The problem I see that there are gaping holes in chassis and panels. This would also mean remaining metal will of be compromised at this stage i.e. thinner. After repair this is still a danger to be on the road. If it was a one of the kind /classis OK, but it is not. So should have been junked and sold for parts and taken off the road

@StevenRobertTaylor Ай бұрын

Hi, you are correct in your statement about the remaining metal being thinner, but that is just how aging vehicles goes. I check this car regularly, it has passed two more yearly safety inspections with no issues. I have checked the entire chassis over and it is still solid, in fact there is still factory paint on the front half in places. It is true it is not a one off classic but I have owned this for many years and there are no other ones I have seen in my local area. Scrapping it for parts is abit dramatic at this stage. Thanks for watching.

@StevenRobertTaylor Ай бұрын

@@vikingdrummer9140 Yeh that comment was a little dramatic. Vosa wouldn't do anything, car is 100% legal and MOTd

@aaron1727 Ай бұрын

So satisfying when the bead broke

@StevenRobertTaylor Ай бұрын

Yeh, that's the hardest part really!

@aaron1727 2 ай бұрын

Impressive strength

@StevenRobertTaylor 2 ай бұрын

Yeh it surprised me, could take abit more aswell

@willtricks9432 2 ай бұрын

Impressive capacity on that tray, nice work. Cheers

@StevenRobertTaylor 2 ай бұрын

Cheers, it's definitely fit for more but I really didn't want to fold it in half 🤣 thanks for watching

@davidowens2320 2 ай бұрын

Excellent video,thanks.

@StevenRobertTaylor 2 ай бұрын

Hi. Thankyou, glad you found it informative.

@6pack1204 2 ай бұрын

Oh no, how not to do it.

@StevenRobertTaylor 2 ай бұрын

And why is that?

@user-mx7xd4pk5h 2 ай бұрын

I like these thin crimp sleves & heat shrink.

@StevenRobertTaylor 2 ай бұрын

You prefer solder joins ?

@user-mx7xd4pk5h 2 ай бұрын

Soldier is fine, but they make these little crimp sleeves you slide over the twist & crimp, & you can solder or not. Makes a neet connection.

@StevenRobertTaylor 2 ай бұрын

@@user-mx7xd4pk5h sounds good, I didn't want to cut the original wire so didn't have the option to slide any type of crimp or heat shrink onto it

@leecbracing 3 ай бұрын

Not been run for years so revs the balls off it 🙄

@StevenRobertTaylor 3 ай бұрын

I didn't want it to stall 😁

@highgatehandyman6479 3 ай бұрын

Mines gotta honda gxr 120. It's belle 320.. it runs so sweet. I really love it. Gives me the horn when it starts

@StevenRobertTaylor 3 ай бұрын

Wow, glad you enjoyed the video. Thanks for watching

@peterszokronyos8070 3 ай бұрын

Awesome video! I have to do the same things on my Pajero as well soon. May I ask what wheels do you have? They look great!

@StevenRobertTaylor 3 ай бұрын

Hi, thankyou! I think that's part and parcel of owning a pajero is having to have it welded at some stage. They are made by a company called Centerline, which I believe are American. 15" diameter and 33" Cooper STT tyres. Thanks for watching

@philmcintire4365 3 ай бұрын

so is usin shrink wrap to cover soder😅

@StevenRobertTaylor 3 ай бұрын

Didn't want to cut the original wiring, covered it with self amalgamating tape. It lasted this long on scotch locks 🤣

@soren3142 3 ай бұрын

Thank you for the informative video. What could be the problem if a new capacitor doesn't solve the problem and the machine keeps not quite spinning up and blowing fuses?

@StevenRobertTaylor 3 ай бұрын

Hi. If you are still blowing fuses the motor is overloading on startup. Check there HP hose is not pressurised and connected (pull the trigger) and check to see if you can turn the motor over my hand using the fan on back of motor. If this is jammed solid then you have a problem in the oil side of pump or the motor. Thanks for watching!

@sanczes6916 3 ай бұрын

Great job! I bought my pajero few weeks ago with the same paint job as yours, and i finded out there are some covered in thick paint holes in floor :,) several sheet metal workers refused to help me, even though I wanted to pay them extra (in my country cars on frame are uncommon), I was resigned, but I pulled myself together and decided to learn welding, I live in an apartment building in a big city, so it will be difficult. Your video helps me a lot, for example by telling me how to get rid of plastic, great job my friend i hope my dreams with overland car will come true soon. Big regards from Warsaw Poland!

@StevenRobertTaylor 3 ай бұрын

Hi, amazing that my videos are helping people in Poland! Yes very time consuming doing welding on old cars but if you can put the hard work in it's very rewarding! Always clean the metal back, get a good earth, mess with welder settings to get the correct current and take your time. Don't weld too much in one place or the metal can warp. Good luck with your restoration and thanks for watching!

@sanczes6916 3 ай бұрын

@@StevenRobertTaylor Thank you very much for your advice! I will definitely listen to you. Every day I discover new rust, but I believe that nothing is impossible :,)

@mdirtydogg 3 ай бұрын

Quite a helpful video and a nice looking Pajero. Thank you.

@StevenRobertTaylor 3 ай бұрын

Hi, thanks! Yeh they don't make them like this anymore that's for sure.

@mdirtydogg 3 ай бұрын

@@StevenRobertTaylor, Absolutely. Everywhere we see, we see electronic wonders. Please do consider putting up more videos as you do repairs on this vehicle. It will help people like me a lot. Thanks again.

@StevenRobertTaylor 3 ай бұрын

@@mdirtydogg Yeh, I recorded one to upload where I did the timing chain and a service. It should be uploaded soon. Thanks for watching.

@robertjones5388 3 ай бұрын

Good vid,thanks. I also have a 530b 11m that we bought for our new build, saved so much work and labour! Their absolutely cracking machines,looking forward to seeing the next vid on it.

@StevenRobertTaylor 3 ай бұрын

Thanks! Yes these machines are so useful. They are heavy no doubt, we have a personnel cage which my father and I built that we use quite alot. I have started filming the repairs to the rams but haven't finished the job yet! Thanks for watching,

@nenormatica 4 ай бұрын

Странно, что после такого простоя не нужно было синхронизировать карбюраторы. А так мотоцикл очень надежный. классика.

@27forme2 4 ай бұрын

How do wire it to the burner?

@backwoodssawyer1 4 ай бұрын

The rotating grapple is a great attachment for handling logs...

@aqib2000 4 ай бұрын

How much was the nozzle and what’s the pressure on the gauge set to. Getting one of these which smokes a lot to fix. Any obvious pointers

@StevenRobertTaylor 4 ай бұрын

Hi, nozzle was only about £10 fuel pressure should be about 8bar. Check your filters and change the nozzle if you're having smoke.

@aqib2000 4 ай бұрын

@@StevenRobertTaylorit’s specifically black smoke though not white Cleaned it out and nozzle definitely isn’t blocked

@StevenRobertTaylor 4 ай бұрын

Black smoke would indicate over fuelling. What size is the nozzle in gpm?

@rhaymarkJZX 4 ай бұрын

Awesome video! I have to the same to my Pajero! It has 124k KM on it but sadly bits of sills has rotted.

@StevenRobertTaylor 4 ай бұрын

Thanks! Yeh this was a labour of love. Probably wouldn't have bothered if it was any other vehicle.

@_XRMissie 5 ай бұрын

Been looking at so many old bandit vids for mechanical research (looking for a 97 mk1 b12 to replace my 08 650) so this ended up in my feed. I cannot believe that started up so easily after being sat for so long. When you said you hadn't even drained the petrol, I was bloody gobsmacked. It's stuff like this that I love about these old bikes. They just don't make em like they used to, and that's coming from a Gen Z. To hell with all the bs and electrical nannies, gimme an old smelly carb'd bike any day and it'll last a lifetime if you take time to learn and care for it.

@StevenRobertTaylor 5 ай бұрын

So was I, thought a carb drain would bare minimum. That's right, the older stuff needs more fettling along the way but it will last a life time. Thanks for watching!

@GrumpyAlf 5 ай бұрын

Nice vid. How long does it take in real?

@StevenRobertTaylor 5 ай бұрын

Hi, took me around 35-40 hours. That includes the work on brake calipers and drop links.

@GrumpyAlf 5 ай бұрын

@@StevenRobertTaylor Thanks! Best regards from Germany.

@StevenRobertTaylor 5 ай бұрын

@@GrumpyAlf Thanks for watching!

@esge9042 5 ай бұрын

ریدب رنگش😂😂😂

@A_t_o_m 5 ай бұрын

Датчик температуры поменяй.