14:06 "One thing it certainly is". This is why I enjoy listening to him. It's not just the variety of ideas, it's the narrative. You never know what to expect. lol.
@Eaglepass5 ай бұрын
That reminded me of younger studies a fearsome "Cutters fast process" elude decayed. Shifting winds increase inflation position drafting recovery. I've always wanted to build a custom sky bottoms up. Max145.20 prrMegW output break of 5/6 months efficiency probate is exceptional between infrastructure costs evaluating incentive crunching has increased 4/5 million each. (Its like reverse mortgage) Building a land ship is &n my only option. Somethings never change infinite-bun. An editor at a large Newspapers gave me sets of the Britannica. I was in awe a simple paper boy.
@JK-zl7vv8 ай бұрын
Your videos are awesome my friend 🤠👍
@jonathancollister74836 ай бұрын
a long time ago I used to make wind spinners from wood which were similar-ish to this and did not need anything more than a saw and drill to produce. plus threaded bar and bearings. I used wood which was cut into slats about an inch wide and 12 inches long and 3/8 thick. In the centre of the slat drill a hole to take a threaded bar. The slats were stacked on to the bar leaving enough room to put a washer and nuts either end and some bearings. The largest I made was 3 feet long and it needed a good attachment to a wall to hold it as it had a fair weight to it and spun at quite a rate. I had plans to put a generator on one to see what it would produce but never got around to it. Assembled in this manner produced a flat panel which could then be arranged by moving each slat up to a third ish of its width at the outside edge relative to the slat below it to produce a helix. Pretty much any wood can be used from ply to hardwood. I used short lengths of timber and ran them through a table saw cutting slices from the side of the timber 3/81/4 was about ideal ( from memory) to get a nice helix but that depended on the length of threaded bar I had. (Ply would have to be cut on the face rather than the side). Also if you wanted to move the spinner you just moved the slats back so it returned to a flat panel.
@MatthewEng25938 ай бұрын
A good location for this wind wall concept might be in the gap between two houses. It could be wall anchored at both gable ends. And wind would be funneled into the turbine.
@guypehaim10808 ай бұрын
You could run a bicycle chain among the rotors and drive just one generator.
@100roberthenry9 ай бұрын
reminds me of the old lawnmower blades....cool.
@keithw82868 ай бұрын
“Nail a cat to a stick” , gold
@AndreaDingbatt8 ай бұрын
That one gets me Everytime,Lol!!
@amphibiousone79728 ай бұрын
A pole frame cradle might make it more efficient.
@d.p.26809 ай бұрын
You could do the frame as V in both sides, the V pointing at the aksel, would provide more wind, maybe even double. For the last blue blade, sorry can't remember the name, make one long piece of one side, and use it as a mold for GRP, then make as many as you want.
@olilyndale9 ай бұрын
Out of all of these different styles do any actually show sizeable advantages on power output? I am about to start experimenting with a modular wall to power my van system and these look brilliant! :)
@williamchamberlain22638 ай бұрын
Nice
@utubeape9 ай бұрын
Great stuff. You should use the same fan on the same setting each time, maybe put some sturdy cardboard sheets to make a kind of wind tunnel, then you cab see how devices compare with your standardised wind
@Eaglepass5 ай бұрын
It's a principlet of Zia effects here in America existence. Consideration exception is gaining itself populace for designing transmitted disputes. One of my favor is a Hummingbird describe sourced 🦋.
@guypehaim10808 ай бұрын
You could always put screening material up in front of the rotors of the wind wall to protect the birds.
@CarlGolden9 ай бұрын
With the black pipe. You mentioned leaving a section in the middle for stiffness. I wonder if each the top and bottom section were off by 60°. There for when one part were to lose wind pressure the opposite end would be there to pick up to increase the efficiency. I don't know much I was just wondering. I may be totally wrong. Just came across your channel and this is something that I have been interested in for some time to produce free energy.
@thorhammer60408 ай бұрын
the blue turbine - What if you made the top half twist the other way so it would create scoops on each side? Might make it turn faster.
@whatthefunction91409 ай бұрын
I'm making one of these wind panels
@koningbolo47009 ай бұрын
1:43 Ye old telephone device... great stuff...
@Hawkewood9 ай бұрын
If you think 3D is the only way, you need to take a look at the blade drum of a reel type lawnmower.
@hardwareful9 ай бұрын
Are humans more annoyed with sideays motion than vertical motion? Would wind walls with horizontal shafts be less of a nuisance?
@mcroftjr9 ай бұрын
Love your experiments. Would adding a pair of magnets to each end at the axle creating a levitation cushion reduce friction and wear and tear on the fan motor?
@dleung187 ай бұрын
How I get the 3D print file for myself? Give me the name of it , so that I can search around in the internet. Appreciate it. Sir.
@strawman94108 ай бұрын
That builders board blocks wind, better to use round rods on the corners
@julianmarsh79939 ай бұрын
Rob can you show us how to charge a battery bank and draw power from it at the same time please, is it wirred in parralell?
@lukaszkups4 ай бұрын
I want to create a wind wall to power up an extra heater inside my water tank for home heat system (powered by air heat pump) - am I mad?
@jonathanpurves50669 ай бұрын
On the bird deaths topic, more species of birds of gone extinct due to domestic cats, only difference is there are no bodies left behind by the cats to count.