If you have a sloppy shifter in pretty much any model subaru, give this a try, most likely your shifter linkage bushings are deteriorated, a couple bucks and 30 mins and I was back to having a nice tight shifter again!
Пікірлер: 14
@alexanderdavis53327 ай бұрын
Thanks for sharing. My 04 wagon is just as bad! Definitely changing it!
@mickrichBMXWRXJapan Жыл бұрын
Am just about to tackle the same job. What did you use to remove and reinstall the roll/spring pins?
@Z3CHYD Жыл бұрын
a punch small enough to knock out the roll pins, I had to put the punch in an extension to reach the roll pin, and the other side of the shift linkage is a bolt, that one is a bit easier
@cristianflores99332 жыл бұрын
I have an 04 Subaru Impreza outback and mine has the same problem, can you leave the link below cause I need to replace mine, thanks💪🏻
@Z3CHYD2 жыл бұрын
Just search subaru shifter bushing on ebay, I bought one like this one, $20 and fits 95-06 impreza's www.ebay.com/itm/402168003204?fits=Make%3ASubaru&hash=item5da314ba84:g:5n4AAOSwo85hqJkd&amdata=enc%3AAQAHAAAA8D6Er4hcJS14pTHT5xgRwuY3W%2FZ14I0aJ2mjmHfyfVuZL9c0kK%2BFxWgFhIU2dfMJkW62ML0UW9b0oar3N%2FjmAdUPVMdMecK9EgxT68YBzslSEF9yKfAg%2F8ishI3Jc9bV9OoQyvsPpvffxTPXwdcAjJEqRW%2B3XW0JVo5SdeNzS60nriadRDY23jIbzo5F4IG8e%2BDGDmAqUwRhf9QCTEvWvpeNVHGCdb3YDcV%2BMGdA5EvMOIBB%2BA7x2ZdA0DZlindHJq6lMAH%2FplrX6gwXCqK4Ksf9ZAR9YZE7IknOtmwnA0unLzaUYRw6t2kh5IFkGbVR0g%3D%3D%7Ctkp%3ABFBMwsilsKdg
@jacobwaderealestate2 жыл бұрын
Another question. How did you take off just that one part of the center consol
@Z3CHYD2 жыл бұрын
You pop off the cover that has the ebrake lever on it, there's 2 screws under the armrest lid, and the front is just clips, then the shifter section is just clips holding it in
@Daniel-pc2ov2 жыл бұрын
I have a 2010 rs Impreza and the shifter isn’t that loose but it kinda is am I fine or?
@Z3CHYD2 жыл бұрын
It's probably just starting to wear out, your probably fine for awhile, basically just use your best judgement on when it becomes sloppy enough where it starts to get hard to find gears that it's maybe time to change the shifter linkage
@Daniel-pc2ov2 жыл бұрын
@@Z3CHYD just bought a part off amazon thanks gonna be first time
@Daniel-pc2ov2 жыл бұрын
did you do this all from the top or bottom??
@Z3CHYD2 жыл бұрын
Both, you need to unbolt from the top to get the shifter off the tunnel, and down below to drive the roll pins/bolts out to change the bushing