Very special thanks to you for this very clever and mindful tutorial that permit to me to go from the first to the last step without any issue nor any doubt! Best regards

Thank you very much for the very helpful video! It really was a huge help! Also turning the plastic tabs around on the new battery before securing it down was such a great move so kudos to you my friend! All the best :)

Patience of a Saint, excellent tuitorial, kept your cool all the way through the fiddly bits, well done you!

great job, really helpful. I screwed up the screw organization a little bit.... even though you warned us. Much to my amazement, my Mac is functioning thanks to your guidance.

This helped me quite a bit. Thanks for mentioning which motherboard screw was a little longer! I did not remove the trackball. I used a combination of dental floss (which only worked on the side batteries) and a small plastic drywall putty knife to get out the center batteries.

Great video indeed, followed it step-by-step and it worked I even lost and found some of the tiny washers on the trackpad just as you did and at the end a complete success! Thank you very, very much.

This is such a great walk-through. Thanks a lot.

Dear, I am very grateful for your help in publishing this video, after changing a battery for one of these same devices and without your video I would not have been able to, great detail and very well explained. Thanks again.

Thank you for providing this video, I was following along and was able to swap my own battery using this as a guide, thank you very much for your time doing this.

Battery changed! Thank you for this very clear and very explicit tutorial. Sincerely, Pierre

Hey man, I cannot describe how good your video is. Thank you so much for sharing this. I replaced my battery following this video step by step. Best regards from Argentina

I couldn't have done my battery replacement without this video. Thanks a lot for making and posting it!

Thanks for your Video! It’s so helpful!

Thanks very much for the detailed explanation. All best 👏

Your tutorial saved the day! I was following another tutorial where I had to take the board out. However, two of the T3 1.7 mm screws securing the bracket for the display board cable connector were blocked and I had no options. I watched your tutorial and used the trick with going underneath the board! Thank you very much!

Thank you so much for your perfect instructions. Saved me a ton of money!

It really helped me, thank you!

This looks crazy… But I try, and this works! Thank you !!!

Thank You! Saved me $$$.

thanks for this.. lifesaver

Brilliant… thx mate.

the turtorial works!!! thank you so much!!! my computers battery has been replaced successfully!!! ❤️🙏

very helpful

Thanks! I installed it successfully. It was extremely difficult but thanks to you I got it through. Though my new battery works, it gets hot when charge. Did I do something wrong? Any suggestions??

Thanks man

Thanks this was very helpful. Stupid for Apple to put the battery tab under the logic board but guess they do that so it’s harder as you said.

Thank u my brother

Thank you brother.. well done - just followed your steps, new battery in.

Great video - Made the job easy. A virtual 0.8 torque screw driver would have been amazing :)

Phenomenal video! Excellent quality, excellent advice, and excellent tips and specs on screwdrivers special tools etc. I couldn't nor wouldn't have attempted this without your video. I used the scrape method to remove the batteries as shown, but I didn't have a scraping tool on hand. I ended up using a hacksaw blade, which is pretty flimsy when not attached. I used a bench grinder to file off the cutting teeth. I ended up cutting into and arcing one battery pack using this tool, but it didn't harm the computer. Still wondering what happened when the awful decision was made to use adhesive to hold the batteries in place! Thanks again! Keep it up!

Life saving!

Ho thanks so lot ! 👍😉

Thx!

Very good video, well explained in a simple and easy way. Thank you. Could you please tell me where you bought the screwdrivers, since I need good ones, the ones I have have not turned out so good, I would appreciate it.

Hey bro My macbook pro a1990 2018 turning off but trackpad still clicking I reset PRAM & CMR Unplug the buttery Getting warm the motherboard a little After all I use UFD mode to revive the device the a error showed to me : amrestoreerrordomain 0-6 Do you can help me please ? I'm in bad sicouation and I'm in a deeply mode in my life for that loptop. If you can help please and get me a way to turning it on. In my country apple center & official center of the apple not here!!!

Ouch! I broke a nail .. :D ... thanks for the video!

After I did all this. The trackpad started giving a very loud clicking noise! But that only happens when the cable of the trackpad is connected! It had nothing to do with the screws... Any tips?

thx bro ！

This is a gem 💎 for sure, My current office laptop is crashed , I'm Pretty sure the battery is damaged bt I also have another office MacBook Pro laptop that is not working, Wanted to replace it's battery to the current laptop Im using... But I'm pretty scared , since I have to do this 2 times on 2 office laptops 😑 I'm really stuck can't resume my work ...

following this step on video, i can change my mac battery succesful Thanks

Hi, I changed the battery but it doesn't turn on, I can feel the trackpad clicking, I've tried resetting the smc and nvram, but it doesn't turn on! help me, sorry for my english, I'm from Brazil

Hi, great video. What is wrong, when I can turn the macbook on but if connected with power it doesn't charge?

Thank you so much this video really helped, Do you have a video for removing the fan and applying thermal paste?

Where can I buy the metallic blades that you used to remove battery?

Hey i got a battery x icon after replacing. Dont really know what the problem is. Does anyone have any solutions or suggestions on how to solve it? Thanks

Hey! You got any links for the OEM battery replacement?

I have a question, what is the s wire near the battery ? I had an issue when removing it

Thanks for the video! I changed battery but now keyboard isn’t working… no activity. Touchpad works fine…

Hello, man, what brand of screw driver you used? Its looks very pretty). Many thanx.

hi, what battery did you use?

What to do if you break the seal of the battery and a flame pops out?

be careful with a metallic blades because if you punch the battery it can start a fire right away

Great video - well done! Personally, I don't trust myself not to destroy my MacBook for the sake of $100 saving :-)

That is not dental floss, but dental tape, which is different.

Use alcohol and hotel room keys to get the batteries loose.

As someone who's done this for over 20 years, you NEVER use a metal tool when working with batteries. ALWAYS use Plastic spudgers. Second, ISO Alcohol is your best friend when it comes to adhesives. Great video, but you really could cause injury to your self and the equipment you're using by using metal pry tools around batteries. All of us professionals do NOT use metal only plastic. Check Ifixit for additional tools that will help make this process easier for you and safer.

Why be difficult, when, with a bit of effort, you can be FNG impossible!!