1998-2002 honda accord transmission removal rear main seal

Рет қаралды 43,896

All Tsab

3 жыл бұрын

transmission removal, installation, and rear main seal replacement

Пікірлер: 106

@clarkkent4991 2 жыл бұрын

I gotta tell you that you are EXCELLENT!!! Your instructions are spot on and VERY clear!!!! My mom has this issue with her car right now. So I personally thank you for taking time to make the video even though it’s for an older car. You are truly a blessing! Take care and be safe. 🏆🧐

@westhouse4641 3 жыл бұрын

This mentality is what advances humanity as a whole. The record and sharing of knowledge gained by one person, to be passed on to countless numbers of people in future generations.

@P0PC47 19 күн бұрын

I'm 17, manual swapping my accord. This video and others are invaluable compared to the many forums and manuals available for this car

@tat3r802 Жыл бұрын

I almost died with anxiety when you placed the boards on the car. The engine support bar relies on the grooves in the engine bay to avoid slipping sideways and causing damage or injury.... Glad you and the car survived.... not a lot of information available on this project. Thank you for sharing your experience

@mikehebert71 3 жыл бұрын

I thank God people like you exist. I have this car and this is more valuable than the entire Hanes manual! Thank you so much for recording this.

@alltsab 3 жыл бұрын

You welcome i am appreciated you valuable my work and thank you for watching my video please help me subscribe too ok tanks

@clarkkent4991 2 жыл бұрын

Ditto!!!

@MyAnonymous2000 Жыл бұрын

@@alltsab If I'm having the rear seal done is there any other seal that might need replacing? I heard someone mention an o-ring that is close. Do you know which one? I have a 99 Accord with 125K. I want to have it fixed. One mechanic said it was too hard to do, because some grooves can form on the crankshaft. Another said it isn't hard with the lower mileage and a sleeve can be used if need be. I saw some mechanic on KZfaq say that something fills in those grooves. Not sure. Thoughts?

@alltsab Жыл бұрын

@@MyAnonymous2000 I'm kinda lost you here I'm not sure what seal or grooves you talk about. But let me tell you what I know only. If oil leak for 4cylinder Accord ok. You have camshaft seals, crankshaft seal which is front seal, and rear main seal which is you have to remove transmission to do it. Other then these seal than you have the VTech seal that all it. One more, if they have distributor then there is a seal at the distributor shaft as well there is not other things than what I mention here. If I'm not clear enough please ask thanks for the subscribe to my channel.

@MyAnonymous2000 Жыл бұрын

@@alltsab Thanks. I'll try to explain this. I subscribed. :) When I went in, the mechanic told me I had a rear seal leak. I agree, because I can see where it is coming from. It's by the transmission (bell housing) He said that he didn't want to repair it, because he has seen a groove on the crankshaft form from where the old seal leaves a groove. I also read that some o ring should be done when doing the rear seal. I think it was said to be near some plate. I really wish I were mechanically inclined. I understand the rear seal/crankshaft potential groove, but I had to watch a lot of videos to understand that one. Where is the V tech seal? I wonder if that's it.

@OYisit 3 жыл бұрын

Best piece of advice here is when doing heavy line repairs never consider using inferior aftermarket parts.

@raidernation3987 Ай бұрын

Thank you so much, I love the step by step video that helps me change my transmission out of my 1999 Honda Accord.

@alltsab Ай бұрын

You welcome

@fsdweaver9199 3 жыл бұрын

Enjoyed watching and seeing a master at work!

@Surplus1 3 жыл бұрын

This is awesome like you said not all people are rich some people have to keep what they have going. Great video

@alltsab 3 жыл бұрын

Thanks buddy

@stanhall6424 Жыл бұрын

thanks, during hard times you can save a lot doing these jobs yourself. it helps a lot when you show the sequences and tricks to get things to go smooth. happy new year bro!

@alltsab Жыл бұрын

Happy New year

@joseprado8532 3 жыл бұрын

I got the 3.0 v6 1999 accord thanks for the Video man

@dezirtboyz3575 Жыл бұрын

Amazing video, Did a really great job. 🙏🏽😁 I’ve already taken my engine out and back in with an engine hoist but now I need to swap the transmission and this is a timesaver. Definitely gotta get a transmission jack. 🤙🏽

@alltsab Жыл бұрын

Nice

@heyitschinoable 3 жыл бұрын

I know this isn’t easy working on the floor on your back. You’re great and do what you can with what you have. Excellent video brother.

@fixbuildmod 9 ай бұрын

thanks for taking the time to make this video for all of us

@alltsab 9 ай бұрын

You welcome

@johnjohn-ny4oi 2 жыл бұрын

Good video, hit the important parts. Thanks

@drippingwax 2 жыл бұрын

I replaced my air intake tube for $25 or less from eBay. The only thing is I have a 1999 and the aftermarket tubes are more like the 2000-2002 part, which has an opening for a secondary intake resonator. The opening is blocked off for 1998-1999 Accords, but nonexistent on my original tube.

@pirihern9329 Жыл бұрын

Good to know. I'm retired 70 lineman. Do same under car no lift. I do have all the tools I need. Xtool ip819 bidirectional scanner I just got

@josephshultz6726 Жыл бұрын

I have the same 01accord but with a manual transmission. You are a monster. Mine rear main seal leaks quite a bit. Would love to attempt this but don't think I'd end up with a working vehicle. Nice work.

@alltsab Жыл бұрын

You should it look hard but is not that bad when you actually doing it. Older Honda only have half frame so not difficult as the full sub frame one. You can do it if you have questions I'm here to answer any questions.

@josephshultz6726 Жыл бұрын

@@alltsab That's very kind of you. I may do so when I locate another daily driver. I would love to do this for the education and experience.

@WibbyKDX 6 ай бұрын

Thank you sir I’ll be doing mine soon

@timmystewart3826 2 жыл бұрын

Thanks 4 video help me so much

@alltsab 2 жыл бұрын

You welcome

@danielsun1463 3 жыл бұрын

OH I see the part number, thanks!

@grahamlittlefield4021 11 ай бұрын

Thanks great help

@ogkrillin9834 3 жыл бұрын

Great video my friend

@alltsab 3 жыл бұрын

Thank buddy

@efrensaclolo7021 3 жыл бұрын

You must replace the intake hose ,that will not pass emission will fail on visual inspections.

@huanweili7699 2 жыл бұрын

Can I take out the transmission from the top on a 09 Honda pilot? Look like i have the coolant pipe and thermostat housing and egr in the way. If I remove them all out, I should have space to get transmission out from the top, right? Any help will be appreciated.

@Castillo408_ Жыл бұрын

Imports babyyyyy ❤

@dudemann3068 2 жыл бұрын

I have one old honda accord I need this please and thank you for this video

@alltsab 2 жыл бұрын

You welcome

@stevesutube01 7 ай бұрын

Did he show the torque converter being unbolted from the flywheel??

@moshewakatelutiw6233 3 жыл бұрын

I’m pulling a much older and easier transmission right now. 1980 accord. 5 speed. I removed almost everything other then the axles. The whole engine and trans tilted. A little worried about getting back under the car. I hope I didn’t remove a brace I wasn’t supposed to remove…

@dannelswarzentruber289 6 ай бұрын

Tilt is normal in my experience

@precisionautotech980 10 ай бұрын

What editing software do you use?

@brianselock5410 3 жыл бұрын

Thanks for the video. I need to do this on my 1998 Acura 2.3 Cl. I believe this is the same as the Honda Accord 2.3 ?? I'm leaving ponds of oil everywhere. The Honda dealership I went to also said their is a large O ring to install.? Is that O ring go onto the tourqe converter?

@alltsab 3 жыл бұрын

No it in the engine crankshaft

@danielsun1463 3 жыл бұрын

Thanks for the video my 1998 Honda Accord has the same problem leaking oil. Mechanic said I need to get front and rear main oil seal to replace and labor is expensive over $1000 maybe. What are the Honda part numbers for the parts needed to do this job or replace? thanks in advance.

@alltsab 3 жыл бұрын

Parts are cheap both front and rear less than $80 from honda.

@russelltorres111 2 жыл бұрын

Was this a Automatic or Manual transmission?

@johnferrari3984 Жыл бұрын

Hi, I have this issue with my 2001 Honda accord. Could you do this for my car? I need to keep my car going. Where are you located?

@kangokidkidd4037 3 жыл бұрын

Thank sir I need to do this my 2000 Honda accord is pissing oil all over

@alltsab 3 жыл бұрын

You welcome its fun

@kangokidkidd4037 3 жыл бұрын

So the atf or blue devil won't stop leak

@alltsab 3 жыл бұрын

@@kangokidkidd4037no and not good to used those sealer

@charliebrown1689 Жыл бұрын

Nice video helped me a lot with my seal replacement. Only problem I have right now after doing all these steps is that I have a code 8 tdc sensor CEL . What do you think I did wrong? Maybe engine moved while distributor was off?

@alltsab Жыл бұрын

Review of what you been removed and didn't put it back exactly. Check your code and follow that code to fix it

@charliebrown1689 Жыл бұрын

@@alltsab thanks for the reply!

@RuthlessEntertainment 3 жыл бұрын

About to do this job on a 1999 Honda Accord only difference is it’s a clutch....so I’m a little worried. Any helpful information would be useful

@alltsab 3 жыл бұрын

Taking out is about the same

@OGS_623 3 жыл бұрын

What’s the name of the tool used to take the rubber piece from the transmission?

@alltsab 3 жыл бұрын

Seal removal tool

@davidparker1091 Жыл бұрын

very helpful video. One question. There is a black hose that comes off of the transmission. I can see it in your video but I cant see what it connects to on the motor side. Its somewhere by the starter but I can't figure out where it goes. Are you able to help?

@alltsab Жыл бұрын

Do you see in my video?

@davidparker1091 Жыл бұрын

Yes I did but you didn’t show where the small hose that is on the transmission goes. You can see it in the video but not where it is connected.

@alltsab Жыл бұрын

@David Parker did you mean the little air hose on top the transmission?

@alltsab Жыл бұрын

That is clipse to the transmission hook or just clipse to any hose to make sure that is stand up that is just like bleed air hose from the transmission it doesn't connect to another hose.

@davidparker1091 Жыл бұрын

The little hose you see at 5.09 in your video. It comes off the transmission below the motor mounts. I usually take pictures when I unhook stuff but missed that one.

@TheaccordMedia Жыл бұрын

I have done all these steps and checked other videos but my trans still won't separate from the engine any ideas?

@alltsab Жыл бұрын

Should be one more holding by the rear motor mount bracket.

@kangokidkidd4037 3 жыл бұрын

How long will this take 6 hours on a Saturday maybe with 2 people

@alltsab 3 жыл бұрын

Yes

@davidcamilleri3918 3 жыл бұрын

Forgot to show REMOVAL of the flex plate to torque converter 10 mm bolts during disassemble

@BriantWebster 3 жыл бұрын

11:45

@lindagallegos7167 Жыл бұрын

Do you have a video that helps me figure why my 2002 Honda Accord quit shifting 3rd up then none of the 5 gears will shift not even reverse.

@alltsab Жыл бұрын

I don't have a video on that but I believe your transmission is going out. That year Honda did have transmission issues.

@lindagallegos7167 Жыл бұрын

Thank you so much for responding. I was afraid of that. I watched your video on replacing tranny. Car has 385000 miles. Engine was burning oil but not dripping. Didn't expect a tranny problem since it was 5 speed. Guess I'll have to say farewell. Loved that car.

@alltsab Жыл бұрын

@@lindagallegos7167 if you have 5 speed and never replace clutch I would drop the transmission and check the clutch. It could be your clutch is bad too

@lindagallegos7167 Жыл бұрын

The clutch was getting closer to the floorboard when shifting but not to the floor. Thanks for that. Can't really afford to buy anything just yet. I really appreciate you're feedback.

@alltsab Жыл бұрын

@@lindagallegos7167 please help me subscribe 😊 thanks

@absolutea.j2837 3 жыл бұрын

I want u to do my car how much would u charge on something like this

@alltsab 3 жыл бұрын

A case of beer

@ilovemyej81 4 ай бұрын

alltsab what's your nationality? hmong?

@cblizay1165 2 жыл бұрын

Grease up the threads on those loaner tools lol

@yangbill6714 3 жыл бұрын

What is that ratchet wrench called

@alltsab 3 жыл бұрын

Ezred, but the new one is no good they are short and thick

@kangokidkidd4037 3 жыл бұрын

So there is no need to take that plate behind rear seal because is not leaking

@alltsab 3 жыл бұрын

Yes if you want to but for me if no leak i leave it alone.

@kangokidkidd4037 3 жыл бұрын

@@alltsab thanks mine came in package with both..still under car don't have fancy jacks so will see how it goes..only have stands and one big jack. Will find wood to hold engine up..

@alltsab 3 жыл бұрын

@@kangokidkidd4037 if filpro brand i will leave it because filpro gasket is terrible

@kangokidkidd4037 3 жыл бұрын

@@alltsab hey me and my 3 son's finished the job started Friday night and finished Monday..the plate behind the seal had some oil sitting on top not sure if it was oil being shot upwards so I took the plate off cleaned it really good and used Honda bond from dealer didn't use the gasket that came with seal also while doing all that replaced the torque converter seal since all i had to do was slide off the torque converter and put new seal also replaced the seals on both CV axles since they were out...fresh transmission fluid everything went back smoothly just took time oh I had no special jack either just one Jack to get car up put on Jack stands and used some bricks and wood to hold engine at bay and used the main Jack to lower transmission...thank you so much you inspired me to fix it right instead of that stupid bottle rear seal that didn't work for my car it was dropping like half a cup of oil but no more...

@alltsab 3 жыл бұрын

@@kangokidkidd4037 weld one buddy great job I'm proud of you.