I just got a 2000 Honda Accord SE. You have become my go to guy for menachical work videos. Thank you.
@BulletSolano4 жыл бұрын
Thanks
@martincontreras60313 жыл бұрын
Where is the VVT 3.0 Honda Accord EX 2000 V6 located?
@BulletSolano3 жыл бұрын
On top of the oil filter housing
@Ariztid5 жыл бұрын
I could not figure out where the leak on my dad's Accord was coming from, but I came across this video. It was a pain to get those bolts out but I got the job done. Thanks for sharing this, Bullet.
@BulletSolano5 жыл бұрын
No problem
@ddeltiempo5 жыл бұрын
Just replaced this whole VTEC solenoid, got a brand new one for $30 on eBay. Followed this video, excellent instructions. USE BOX-HEAD WRENCHES they will make your life a lot easier. Thanks for the video!
@BulletSolano5 жыл бұрын
No problem
@jacko-136 жыл бұрын
Thank you Bullet Solano. This video was extremely helpful. I followed the guidance to replace the gaskets in my Honda Accord EX 2002 over the weekend. I took your tip and made a very small wrench by snapping off one side and grinding the broken end smooth on a bench grinder. One tip though: my ring wrench didn't fit over the top nut and I actually had to grind away on the ring to make is slimmer. After about 5 grind/check fit cycles, I ended up making it so it could slip over. After that the rest was easy. Thanks again! Really enjoy your videos.
@Gandoff20006 жыл бұрын
My wife's 1999 honda accord was leaking 3 quarts in 100 miles (on the passenger side of the car)! I could not see where it was coming from. Changed the distributor O-ring, still leaked. replaced the VTEC to head gasket but it did not look bad. Replaced the gasket under the solenoid. The leak stopped. The gasket under the solenoid was brittle and I suspect leaking. Getting those three bolts for the VTEC to head broken lose was not easy. I used a 10mm boxed in wrench and some uncool methods to get enough leverage on the wrench to get the bottom one lose. (included a hammer, a hatchet and a crowbar). Taking the water inlet off would have made it a lot easier but I did not have the "O" rings and gaskets for it and having to catch the coolant would have been a pain. One more thing, I replaced the PCV valve. A bad one can make seals fail. Thank you for the video!
@BulletSolano6 жыл бұрын
+Gandoff2000 ok cool, and yes ti remove those 3 bolts is not a fun job but I have the same experience
@williameldon87686 жыл бұрын
Thanks for the informative comment. Did you have any symptoms of failing VTEC solenoid or just leaking oil? Thanks
@BulletSolano6 жыл бұрын
+William Eldon thanks Bro. No problems with my solenoid just leaking oil
@Gandoff20006 жыл бұрын
William Eldon on mine, yes, everytime the oil got low, the engine light came on with a 1259 code which indicates a problem with the vtec. But that went away after the leak was fixed.
@arielban16 жыл бұрын
thanks gandoff for your detailed experience
@arielban16 жыл бұрын
Thanks for the video Bullet.. I was able to perform this procedure easily. I followed your video, but I used the Harbor Freight Box End off set wrench 8 pc item 32042. This enabled be to get the bottom bolt off. I had to wiggle and work the wrench as it was tight, but the nut eventually came loose. I also cleaned the EGR since I had to remove it for the VTEC gasket replacement. In addition, I tested the VTEC solenoid per your instructions.. That was excellent testing procedure. I learned something... thanks again.
@BulletSolano6 жыл бұрын
Great and thanks for the advice on the wrench
@AngelSanchez-ig3jt5 жыл бұрын
I kept thinking that my valve cover was bad. I've changed it twice in the last 2 years but it would always leak from the back side. Now I'm starting to think it's this solenoid. Thanks for the video.
@BulletSolano5 жыл бұрын
No problem
@anthonys.25525 жыл бұрын
My mechanic quoted me $600 to replace this. I am thankful I found this video now !
@BulletSolano5 жыл бұрын
No problem, It’s not easy process but $600 is crazy
@BulletSolano5 жыл бұрын
Here is one more just in case kzfaq.info/get/bejne/jsVhf5h32sWsY58.html
@mosessanchez82532 жыл бұрын
Thank you for taking time in the past to show us how to take care of your 6th gen (2002)
@KreationsOvMatt4 жыл бұрын
Doing this on my wife’s car this coming weekend. This is my tutorial. Thanks for the in-depth video. Wish me luck!
@BulletSolano4 жыл бұрын
Good luck
@Hachiro3 жыл бұрын
To viewers: Make sure to not lose the spring that holds the plunger in place. I dropped mine without noticing, and it made the car go into limp mode. Rewatched Bullet's video, found the spring, and once I installed it, the car ran fine again xD
@michaellindsey314 жыл бұрын
YOU MAKE EVERYTHING SEEM SO EASY GOOD JOB 👍
@BulletSolano4 жыл бұрын
Thanks
@aaron1231122 жыл бұрын
Man so many of your videos have saved my ass!!! Thanks for taking the time to teach all of us!!!
@takethedamnphoto3 жыл бұрын
Thank you man! Just waiting for parts and using this video to do it myself. Probably a $500 job at the shop!
@BulletSolano3 жыл бұрын
No problem
@SuperChad13136 жыл бұрын
Dude......thanks for covering everything. You win the Internet today.
@BulletSolano6 жыл бұрын
No problem bro, thanks
@azweaver96003 жыл бұрын
Thanks for the video, I used it as a guide to replace my gasket. I did one thing differently, I also removed the oil pressure sensor from the spooler. Once that was done I was able to access the bottom bolt with easily with an offset wrench. Thanks again.
@BulletSolano3 жыл бұрын
No problem
@dougallen34785 жыл бұрын
Thank you for your comment , So tell me why do you think that seal would start leaking that bad ? And i`m gonna believe that the motor has to come out to do this , Correct ? Also how can I be sure that`s where the oil is coming from ? I just got done hosing the whole engine the best I could with some degreaser , Gonna let it set till morning , Then hit it with the water hose . Again thank you for your help and keep up the good work on your videos , They have been very helpful in me repairing my car .
@BulletSolano5 жыл бұрын
Thanks man, tomorrow clean the engine from the bottom and check in between the engine and the transmission is you see oil around that area then you have a bad rear main seal, and the transmission has to come out to do the rear mail seal
@melbourneman11785 жыл бұрын
great vid!. love your clean engine bay! my o rings may have been leaking for years. its dirty on that side of the engine, will clean today. shes gettin old with 264,000 miles!
@BulletSolano5 жыл бұрын
Thanks
@dantewilliams27355 жыл бұрын
Awesome dude ive been trying to figure out how to get the solenoid off for a week!!! Never thought to take the egr valve off! 😅😂
@BulletSolano5 жыл бұрын
No problem bro, thanks
@dantewilliams27355 жыл бұрын
No bro 🙏 thank you
@Julian-zy1em3 жыл бұрын
My transmission is acting kinda funny.. almost like the VTech takes a second to engage. My brother told me this was the problem, it happened to him. Once again thanks for another great video!!!
@BulletSolano3 жыл бұрын
No problem
@robertosaldateii56915 ай бұрын
This is a great video man. Might buy one of these that needs a solenoid replaced. Will come back around to let you know how it goes!
@user-ib8rg7vn8c2 ай бұрын
Absolutely love your channel
@matador197002 жыл бұрын
Good video , I ll try with my 99 accord , I have that problem now , thanks
@bidsanand5 жыл бұрын
Awesome video, really like the way you explain. Did my vtec replacement. Would like to give a small tip, to remove the third bolt under the valve I developed a technique, attached pics to explain. Just in case someone feels difficulty in getting to it, i guess it’s called buddy wrench technique. And don’t even try the bolt without a small 10mm wrench. Cheers..
@jamesc69453 жыл бұрын
Just did mine on my accord, what a difference. Thx👍🇨🇦 be patient people it does come out, with a few swear words 🤣😂🤣😂🤣
@mr.luislarios62954 жыл бұрын
well done it give me a positive idea how to do my project thank you
@BulletSolano4 жыл бұрын
Thanks, no problem
@carroll65 жыл бұрын
my questioned was answered after watching just a little while.
@ianpenn33665 жыл бұрын
I use a 1/4 ratchet to loose the two nuts on top And a 10mm combo wrench for the bottom
@MrHines883 жыл бұрын
I got Honda 2door Coupe EX that im trying fix up so your vids bru is very help learning material
@BulletSolano3 жыл бұрын
Thanks bro
@StreetMisfit4 жыл бұрын
Very good video. I enjoy your work because it’s very thorough and recorded well. It is difficult to find great quality work. Keep it up 👍🏽
@BulletSolano4 жыл бұрын
Thanks bud
@mikeokay32376 жыл бұрын
Hey bro your valve cover gasket replacement video helped me , and yet again this video helped me out also thank you for making these you helped me out so much I really appreciate you making them
@BulletSolano6 жыл бұрын
No problem bro thanks
@roberey68212 жыл бұрын
Excellent videos from these guy good job.
@koreymayo88845 жыл бұрын
I have a feeling this is where my oil is leaking. I already did distributor gasket and valve cover gasket.
@mr.profezzional69353 жыл бұрын
Hi, what gasket ended up being the leaky one?
@chasemiller79746 жыл бұрын
Badass looking motor.
@BulletSolano6 жыл бұрын
Thanks
@dougallen34785 жыл бұрын
One more thing I forgot today I pulled all 4 plugs and all were burning like brand new completely dry car runs great just can`t find bad oil leak
@EGLALGEXLAJOSEPHS Жыл бұрын
Thank you Bullet...
@BulletSolano Жыл бұрын
My pleasure
@farshadnikzat8571 Жыл бұрын
GREAT JOB
@lilbbbbbbb5 жыл бұрын
Clean looking engine man thanks for the video
@BulletSolano5 жыл бұрын
Thanks, No problem
@JessicaNavas5713 Жыл бұрын
Laparascopic precision as always, avoiding unneccessarily cracking open gaskets and you found access without even taking out your air intake. Impressive. Do I need to cut my 10mm in half to do it? I have a small one, but I guess I will see.
@BulletSolano Жыл бұрын
Probably you have to
@arielban16 жыл бұрын
Bullet, what camera did you use? the clarity is awesome. thank you
@BulletSolano6 жыл бұрын
+arielban1 thanks Bro for all my videos I use a Sony RX100. I live that camera is very good
@arielban16 жыл бұрын
Thank you Bullet. I have the Sony DSC unit.. the predecessor. Mine is 10MP. Your unit is 20MP. After seeing your video, I will upgrade. Hope to get a good deal during November.. thank you again.
@BulletSolano6 жыл бұрын
+arielban1 no problem Bro. I was thinking on changing the camera but I think I’m good with it
@myronblack88526 жыл бұрын
hey i have a 98 accord torneo with a F20b single cam engine. i always y thought vtec was the solnoid only till i watched your vid, ten thumbs up for clarity bro. Whats puzzling me is that my vtec does not have a sensor attached to it only the solnoid. IDK what to think coz now every vid or pic i see of a vtec it has the sensor attached...
@BulletSolano6 жыл бұрын
I think your engine vtec is control with oil pressure only that’s why
@stalkedskinwalkers9811 Жыл бұрын
If it ain't bullet showing us how to build a Honda I don't watch it
@BulletSolano Жыл бұрын
😁
@mjaye60425 жыл бұрын
Thank you!
@BulletSolano5 жыл бұрын
No problem
@memeco505 жыл бұрын
The only thing you need to do... he says. I was able to remove of the bolts on each side. Tomorrow I'll probably remove the thermostat casing. That's what is not letting me get the bottom bolt. Box in wrench you all saying... Let me look into that. Thanks
@memeco505 жыл бұрын
Done!
@codywoodring Жыл бұрын
Any tips for getting the lowest of the 3 bolts? Can't seem to get mine unstuck
@BulletSolano Жыл бұрын
You have to pull the wrench with all your strength
@Unknown900106 жыл бұрын
good video now i know how to change that you helped me change my thermostat on my car that was made easy can you do a video on how to change the transmission solenoids on that same year honda accord i have a 2000 and i just wanted to know how to do it thanks
@BulletSolano6 жыл бұрын
Ok no problem
@balazosolano13705 жыл бұрын
Check the link in the description
@ronniecarlisle2873 Жыл бұрын
My bolts were very hard to get off . They were over tight , had to make a 10 mm socket and a hand breaker bar to fit lol
@jeffkovene4420 Жыл бұрын
What are the torque specs? Too tight and you will crush the new gasket flat.
@BulletSolano Жыл бұрын
8.7 ft/lbs
@frios9663 ай бұрын
Should I put threadlocker on the bolts
@BulletSolano3 ай бұрын
No need
@cer2us5 жыл бұрын
Just did mine along with the distributor, now no oil leaks .
@BulletSolano5 жыл бұрын
Nice
@christopherrollandwilkins62985 жыл бұрын
Man I see you customize A Honda accord that's cool as hell I have a 2000 and its leaking oil so thank you for the info on finding and fixing. And big ??? "how much did you spend on the customize work on the engine".
@BulletSolano5 жыл бұрын
Thanks man, I have this car for 7 years now and I think in the engine is only like $1000 but the money in this car is on the suspension and brakes!! Probably all the car including labor I spend around $7000 maybe more
@Hawlkeye-e9p Жыл бұрын
That red hoze going to the intake? I don't have anything on that port. Its wide open.
@BulletSolano Жыл бұрын
Put a plug in it amzn.to/3sFa5GB
@prasannasridevi73872 жыл бұрын
Excellent video.. Any recommendations for a good, honest mechanic in Austin areas (TX)? I don’t want to go to big dealers or mechanic chains but prefer one man or two men / family run shops. TIA
@BulletSolano2 жыл бұрын
Thanks, sorry I don’t know anyone there
@christopherhernandez9115Ай бұрын
The p1259 code still comes up on my 2.3l. F series new solenoid valve assembly wiring is good what else can it be ?
@BulletSolanoАй бұрын
Computer
@christopherhernandez9115Ай бұрын
@@BulletSolano can u help me test the wiring from the computer to the connector send me a email I’ll mail u my info yea
@lebronjordan8025 жыл бұрын
Great video 👍!
@BulletSolano5 жыл бұрын
Thanks
@jluc1555 жыл бұрын
Awesome bro .... thanks for the video
@BulletSolano5 жыл бұрын
No problem, thanks
@dougallen34785 жыл бұрын
Hey Bullet ! I have a problem and i`m hoping you may be able to tell me what to do and look for please. I have a 2000 Honda Accord Coupe 2.3 5 Speed . I just recently replaced the head due to valves being bent from timing belts snapped . I have replaced all belts and seals & water pump . I now have a really bad oil leak coming from the back side of the engine and I can`t seem to find where it`s coming from . I`ve already replaced o ring in dist. , I`ve already taken Solenoid apart and cleaned it 2 times and this time I used gasket sealer , i`ve replaced valve cover gasket and all seals in it alsowith gasket sealer on both sides of gasket from cover to head, I`ve already changed oil and filter, only thing I havn`t changed is oil sending switch but it don`t look like it`s leaking . Any help that you can give will be great ! This car is already taken everything I got to repair . Thank You
@BulletSolano5 жыл бұрын
Hey man I think the rear main seal is leaking
@brianscott31282 жыл бұрын
So i brought the whole vtech assembly do i still need to loosen the top three bolts to install it?
@BulletSolano2 жыл бұрын
No
@jorgemunoz49866 жыл бұрын
Very good video man
@BulletSolano6 жыл бұрын
Thanks
@bmtv577 Жыл бұрын
Hi, are those gasket seals fitted on the RA6 odyssey 2003? F23 engine? Are they the same model?
@BulletSolano Жыл бұрын
Should be, but look for a new one at the dealership for your vehicle
@IvanRom1004 жыл бұрын
Hey man! Love your videos..always very helpful...I have a question. I have a p1259 code on my 2000 accord Ex 4cy 2.3l. Could this mess with the EGR. Says I have insufficient flow even tho I just replaced it
@BulletSolano4 жыл бұрын
Hey man, thanks!! Clean the EGR passage
@carroll65 жыл бұрын
Would this be a good time to replace the EGR valve also? What other things might be replaced, or upgraded. Might as well do it all.
@BulletSolano5 жыл бұрын
If you have the money go for it, but in my case if is not broken don’t fix it
@carroll65 жыл бұрын
@@BulletSolano these repairs would cost a lot of money from most shops! The EGR valve I saw a quote for $500 to do it. Even though the parts cost money.. I would say replace the thermostat, EGR, along with just a new Solenoid. The car would be good for a long time, as long as you own the car.
@BulletSolano5 жыл бұрын
That’s right
@lewisgivens45645 жыл бұрын
In my hood where you removed the hoses I don’t have the same setup and it’s a 98. Where you’re big orange hose is mine is connected to the other ones under it and essentially I don’t have a hose where you’re orange hose is I only have the set under that
@BulletSolano5 жыл бұрын
My setup is different because I have a cold air intake
@lewisgivens45645 жыл бұрын
Bullet Solano ahhhhh ok I’m not too familiar with it but thanks man the video helped regardless
@BulletSolano5 жыл бұрын
No problem
@stalkedskinwalkers98118 ай бұрын
Bullet I have a favor. Brother what does it mean when a h22 is shooting water out the exhaust about 4 ft at half pedal
@BulletSolano8 ай бұрын
Condensation, that’s normal in cold weather
@leopoldrobert44983 жыл бұрын
Do you change it everyday?, clean it well it wont be leaking anymore :).
@tannertk68516 жыл бұрын
Este solenoide es el que causa que mi Accord no pase de las 3000RPM?
@BulletSolano6 жыл бұрын
Si ese
@VinnieVega764 жыл бұрын
Your car automatic or manual? Mine's a manual. Was yours throwing a code or are you just replacing it for leak sake? I had to change my rocker arm assembly, and after that I hit the road to make sure all was good. WELL, I was on second or third (manual) and hit it, then the car gave a slight jerk up around 3500-3600 rpm and CEL came on with vtec code. Car drives fine as long as I keep it below 3500 rpm, but I know something needs to be replaced, not sure what. Would you think I need an entire solenoid to be on the safe side or just change the gasket? Your thoughts?
@BulletSolano4 жыл бұрын
Auto, and you need a new valve
@VinnieVega764 жыл бұрын
@@BulletSolano thx
@VinnieVega764 жыл бұрын
@@BulletSolano also, how do you know that? I can drive just fine under 3k rom, or should I just not drive it?
@BulletSolano4 жыл бұрын
Your welcome
@VinnieVega764 жыл бұрын
@@BulletSolano several things I love about you and your channel. A) you have a 6th gen accord, not many ppl do B) you fix a lot of things that help me with similar issues. C) you have a very fast response time to questions. I just ordered a remanufactured one, so is basically new, not a 3rd party one, and it was only 30 bucks 😁😁 also, ffr, I seen someone do the same procedure, except instead of the small wrench he used an offset 10mm one, which I think I may do but I do have a small 10mm as well
@Jessysingh433 жыл бұрын
I wish you showed you removing the bottom three bolts
@BulletSolano3 жыл бұрын
Hard to put a camera in there
@VinnieVega764 жыл бұрын
Where are you touching your positive cable? Inside the wiring harness?
@BulletSolano4 жыл бұрын
Yes
@stalkedskinwalkers9811 Жыл бұрын
Bullet I'm in the crisis, I need your help.! Woke up today been hearing a little jangling around from a starter plate. Crank it over it felt like it was going to go and then all I can hear is my starter spinning like my bolts fell out what do I do and where does the starter hook into the crank? Ain't their gear there like a pinion for the pitch on the starter?
@BulletSolano Жыл бұрын
kzfaq.info/get/bejne/rrWedtRjtq7NpJc.html
@stalkedskinwalkers9811 Жыл бұрын
Also bullet do I have to pull the whole transmission if my flywheel fell off from my bolts falling off on a 2.3 VTEC single overhead automatic transmission
@BulletSolano Жыл бұрын
Yes
@mi_so9663 жыл бұрын
thank you for the video! One question though, on my car only the top is leaking, could I just replace the top one and not have to remove the EGR.
@BulletSolano3 жыл бұрын
Yes
@mi_so9663 жыл бұрын
@@BulletSolano thanks
@BulletSolano3 жыл бұрын
No problem
@ejaymaria87602 жыл бұрын
What's the part number for small gasket that goes on top
@BulletSolano2 жыл бұрын
amzn.to/3FFKh1W
@javierochoa4323 жыл бұрын
How can I know if my vtech solenoid works in my 98 Honda Accord 2.3 ...it doesn’t rev pass 5 rpms
@BulletSolano3 жыл бұрын
Check for resistance on the connector and put power to the solenoid to see if it opens, but if the car doesn’t pass 5K rpm it means that the solenoid is bad or dirty or probably you have low oil, most likely the solenoid is bad
@javierochoa4323 жыл бұрын
@@BulletSolano my oil is full n justed finished doing timing belts n water pump
@Cg6_4oh83 жыл бұрын
I Replaced it bro but it still bogs when I’m accelerating ?
@BulletSolano3 жыл бұрын
Did you have problems with vtec? If not your problem is something else, probably spark plugs, cables, rotor and distributor cap can fix that, or cleaning the egr passage, sometimes your fuel pump is the problem
@Ottonic64 жыл бұрын
Hey Bullet. Haven't seen any videos lately, if you have some, I'm not getting notices. Did you get your new car (maybe that;s why no videos)? Love your vids, and am just curious.. Thanks! Take care.
@BulletSolano4 жыл бұрын
Hey Dano, how are you man, I posted at least 2 videos per week!! I don’t know why yo you don’t get the notification
@lowlifelevi50222 жыл бұрын
Okay this helped alot but quick question can I get a link to that air intake
@BulletSolano2 жыл бұрын
amzn.to/3v7VLXD
@ChangedforeverBYHIM-gabe3 жыл бұрын
I still get the same code and hesitation at high speeds. Can it be something else?
@basillly5 жыл бұрын
hey, did replacing the solenoid make your shifts feel smoother?
@BulletSolano5 жыл бұрын
Is the same
@brittanymarchetta45755 жыл бұрын
Quick ? Woke up car didn’t start noticed cam barely spinning and rotor checked timing belt still intact what do you think
@BulletSolano5 жыл бұрын
Check your distributor
@beboalicea14473 жыл бұрын
My 2005 Honda Accord is leaking oil in the rear of the passenger side I just ordered the vtec do you think that’s what it could be?
@BulletSolano3 жыл бұрын
Probably but you need to check the valve cover gasket as well
@beboalicea14473 жыл бұрын
Valve cover was just changed and it’s pretty dry but the parts on my passenger side of my car are covered in oil
@BulletSolano3 жыл бұрын
Yeah probably the gasket from the vtec solenoid is bad
@beboalicea14473 жыл бұрын
@@BulletSolano okay cause the oil is getting thrown everywhere it’s all over my power steering resovoir and it look like it’s going on my alternator
@bidsanand5 жыл бұрын
Should i drain the engine oil before taking the VTEC solenoid ..?
@BulletSolano5 жыл бұрын
No you don’t have to just put a rag under the solenoid before you removed it
@patrickkoenig84896 жыл бұрын
Hey Bullet, I bought a 2002 Honda Accord 2.3L VTEC about 2 months ago, long story short.. The mechanic said rebuild I am getting codes P0700 HONDA - Automatic Transmission Fault P1750 HONDA - Mechanical Problem in Hydraulic Control System of A/T Clutch Pressure Control Solenoid P0135 HONDA - O2 Sensor Heater Circuit Malfunction Bank 1 Sensor 1 Any history that you've head with these codes or the hard shifting, That can help me?
@BulletSolano6 жыл бұрын
Hey how are you, P0135 you need oxygen sensor P0700 you have problems with the transmission controls P01750 Possible causes Faulty Range Position Switch Range Position Switch harness is open or shorted Range Position Switch circuit poor electrical connection
@hiramalonso973 жыл бұрын
How do I know if I have it put back together correctly ??
@BulletSolano3 жыл бұрын
Check for leaks
@hiramalonso973 жыл бұрын
Thank you! 🤝🤝
@twopiecez52264 жыл бұрын
Which wire in the plug of solenoid do i need to tap the positive wire from battery??
@BulletSolano4 жыл бұрын
It doesn’t matter
@doradean76615 жыл бұрын
Hi, Bullet! I'm trying to find the oem part to that gasket you were referring to that would need replacing if we remove the thermostat housing. I plan to change out the thermostat while I'm doing the solenoid gasket. Would that be called the thermostat case gasket, if so, I see two of them listed for my 98 honda accord 4 cyl, 2.3l: 91312-POA-000? or is it 91312-P0A-000? Do either of them need gasket sealant applied? Thanks a million!
@BulletSolano5 жыл бұрын
Hi, Is the 91312-P0A-000 and you don’t need sealant for it
@doradean76615 жыл бұрын
@@BulletSolano Oops Bullet, I gave same number to both gasket parts. I meant 193-PTO- 000 being the other. Just wanted to make sure I don't use the wrong gasket as I don't want any leaks. Thanks Again!
@BulletSolano5 жыл бұрын
No problem
@jaylunaguitar2 жыл бұрын
Hey Bullet, what kind of wire did you use to test it exactly? It looks like one of those aligator clip things. Thanks.
@BulletSolano2 жыл бұрын
Yes
@jaylunaguitar2 жыл бұрын
The bottom bolt below the oil pressure sensor is awful I can't get it off. I got a stubby 10mm and an 10mm offset wrench and it's making the tool slip. I also took the sensor off to have more room.
@jaylunaguitar2 жыл бұрын
@@BulletSolano Update, got it off. It was just stripped really bad I had to take a hammer and chisel to it 😆. I eventually was able to turn it out.
@hotice1n15 жыл бұрын
So i clean the VTEC use brake cleaner and put new gasket . Install it back but it won’t rev past 4k rpm . I put a quart of oil and still doesn’t past 4K . It shows it has oil . I don’t want to over flow it with another quart heard not good to have to much oil in it
@BulletSolano5 жыл бұрын
Did you check is the valve works?
@BulletSolano5 жыл бұрын
Use the battery like I show in the video to see if the valve works
@hotice1n15 жыл бұрын
Yeah i added some more oil and it work . I had VTEC the whole time just had that nasty leak . I still have to do the egr was gonna clean it but i saw you use throttle body cleaner was scared to clean it with brake cleaner
@BulletSolano5 жыл бұрын
Ok that’s good and when you get to the EGR passage don’t put cleaner in the Idle air control valve because you probably are going to damage the valve just clean the plenum with a rag
@hotice1n15 жыл бұрын
That already happen to me before when i clean intake lol it rev hard afterwards had to get a new one at the junk . But thanks your video are always fun to watch .
@ludmula37563 жыл бұрын
Did your management light come on and it was misfiring ?
@BulletSolano3 жыл бұрын
No, I did this to show how to fixed this issue
@BEAR-3 жыл бұрын
Which pin do you put the positive wire on when testing the Solenoid?
@BulletSolano3 жыл бұрын
Yes
@carmenvega1265 жыл бұрын
Muy buen vídeo!!! Me podrías decir como exactamente puedo pedir los nombres de los dos gasked por favor. Gracias
@BulletSolano5 жыл бұрын
Gracias, búscalos así, depende el modelo y año que es tu auto, en mi caso lo pedí así 2000 accord vtec solenoid valve gasket para auto de 4 cilindros
@BulletSolano5 жыл бұрын
El mío es este, si el tuyo es igual puedes pedir este gasket Dorman 917-170 Variable Timing Solenoid Gasket www.amazon.com/dp/B00TEFMBFY/ref=cm_sw_r_cp_api_i_NMuFDbS1GR39K
@kylecurties11394 жыл бұрын
My 98 Honda accord won't start. I have replaced the battery and alternator and still haven't got it to start what could be the problem?
@BulletSolano4 жыл бұрын
Check your main relay if that one works and the fuel pump is working your distributor needs to be replace kzfaq.info/get/bejne/iNughreG1s2RkoU.html
@permacc60763 жыл бұрын
I got a quick question compita. My valve cover says vtec but i just have a plate where the solenoid should be, engine is f23a1. Why is that? Its a stick shift btw1998
@BulletSolano3 жыл бұрын
Someone didn’t like vtec kick in yoo
@BulletSolano3 жыл бұрын
See if the connector is there, and get a new solenoid
@permacc60763 жыл бұрын
Damn bro ur on it. Ait ill check in the morning thanks
@BulletSolano3 жыл бұрын
No problem bro
@Peguerochannel4 жыл бұрын
Good vídeo
@BulletSolano4 жыл бұрын
Thanks
@davidriberal83444 жыл бұрын
Do you need to drain the oil ?
@BulletSolano4 жыл бұрын
You don’t have to
@davidriberal83444 жыл бұрын
@@BulletSolano thank you
@BulletSolano4 жыл бұрын
No problem
@josem.97003 жыл бұрын
Will this help clear out code 1750 on my 02 accord lx. My D4 light blinks after running the engine so long and D4 gear won't work properly even reduce my speed and start pulling back and forth with no signs of acceleration??
@BulletSolano3 жыл бұрын
No, this is for the engine, your code is transmission problem, replace the solenoid
@josem.97003 жыл бұрын
So just replace the shift solenoid? I see some run for $40-60 and I see an "original" solenoid for over $230 can a price make a difference in been original??
@BulletSolano3 жыл бұрын
Yes, more expensive more better
@josem.97003 жыл бұрын
Muchas Gracias Senor!. I'm taking your word on this. Good informing video!. 👍👍
@BulletSolano3 жыл бұрын
No problem
@Really6585 жыл бұрын
My man!
@VikitorSabino314 жыл бұрын
Hello bullet my master of accord's, I changed the idle actuator of my honda accord to 5 days and everything worked fine until today I called and the car had those acceleration oscillations again, I checked the car on the Scanner obd hondash and it doesn't work no error, what can i do to regulate this acceleration, is now getting between 1500 to 1800rpm with the car stopped in P or N.
@BulletSolano4 жыл бұрын
Vikitor Sabino hey bro if you get a cheap part is going on fail,but first check for intake leak or probably the idle air control valve gasket is leaking!! But if the part is cheap get another one with new gasket
@zacmcnaught84883 жыл бұрын
What intake manifold is that? Aftermarket or stock?
@BulletSolano3 жыл бұрын
Aftermarket
@zacmcnaught84883 жыл бұрын
I got the exact same car. Full bolt on besides the manifold, which one is it? Ive been looking forever
@BulletSolano3 жыл бұрын
😂😂 sorry man I was thinking you said cold air Intake, that’s the stock manifold