2 Furnaces Not Heating | Service Call | Dual Diagnoses
Рет қаралды 6,990
Жыл бұрынIn this video, Josh goes to a No Heat Service Call, where 2 of the 3 systems have stopped heating! Watch through to the end to see several tips and tricks on diagnosing furnaces correctly and efficiently! Also learn a really cool trick to verify a gas valve is working properly, even when the board isn't.
Thanks again to the sponsor of this
video, FieldPulse !! Check ''em out using the link👇🏻
www.fieldpulse.com?lmref=i7nplg
Join this channel to get access to perks:
/ @hvactechtips
@franks6837 Жыл бұрын
Check the condensate pressure switch that actually gives the 24 bolts to the gas valve . More times than not it's that crappy switch that is sticking and not the board . I promise. The company I work for has installed thousands of these furnaces
@OneSaintPaul 6 ай бұрын
We Dig It! Thanks for taking us along this service call!
@synaven6895 Жыл бұрын
Thank you for taking your time explaining step by step. Always enjoyed and learned from your videos.
@HVACTechTips Жыл бұрын
Glad it was helpful!
@jonathanraul4086 Жыл бұрын
Thanks. Great video! Thanks for taking your time out and explaining
@hectormendoza993 Жыл бұрын
Great video ! thanks for sharing tips
@tonydelgrego2906 Жыл бұрын
Nice professional troubleshooting
@deanmartin1966 Жыл бұрын
Good video. Thanks for sharing.
@alirahal5900 Жыл бұрын
Thank you.
@TomLawson05 Жыл бұрын
Great job troubleshooting good video very informative
@dporrasxtremeLS3 Жыл бұрын
Yes!!!
@dxrules1012 4 ай бұрын
Brother that drain switch on those Amanas can interrupt 24v too the valve , always something too test on those when diagnosing that issue
@TNHVACLIFE Жыл бұрын
Good video
@djvirtudazo5027 6 ай бұрын
u know them alligator jumping wire is a freaking made from heaven made my life easier when i do service lol..
@chesstime356 Жыл бұрын
Nice video, was there any burned marks on Board?
@ronniehvac653 Жыл бұрын
I'm on call tonight and I just left a no heat call with the exact same problem as the second furnace you worked on. Board not sending voltage to inducer.
@scottingleman8103 Жыл бұрын
Get the pressure switch hose off the draft inducer
@jorgeespinoza238 Жыл бұрын
Could that home taken a surge and only affected both circuit boards?
@HVACTechTips Жыл бұрын
That's what I was thinking. It's very possible
@Empty7775 Жыл бұрын
Maybe a voltage spike smoked the boards.
@HVACTechTips Жыл бұрын
Very possible 👍🏻
@derekeady8816 8 ай бұрын
Power surge
@buddyholly8999 Жыл бұрын
Rollout switch?
@HVACTechTips Жыл бұрын
A open roll out switch wouldn't let the inducer come on and normally only runs the blower. It would also show a fault code.
@buddyholly8999 Жыл бұрын
@@HVACTechTips Yes your right, the blower would come on.
@hugomoreno9312 Жыл бұрын
Surge maybe
@alexdickerson8356 Жыл бұрын
Every year once it starts getting colder the boards always go bad. The GA curse 🤣
@HVACTechTips Жыл бұрын
Yup 👍🏻
@stephangoritschnig4913 2 ай бұрын
My pet peeve is when I see low voltage wires are not tied together to make things look pretty.
Jumper man Tech
Рет қаралды 13 М.
ACTS Services
Рет қаралды 29 М.
HVAC Tech Tips
Рет қаралды 76 М.
WHITEHOUSE FARM
Рет қаралды 3,6 М.
Юлия Смирнова
Рет қаралды 3,5 МЛН
Двое играют | Наташа и Вова
Рет қаралды 5 МЛН