I had to install a side warning sensor in my CRV. Removing those rear interior panels had me freaking out. your video was most helpful. Thanks!

Hello again. I figured out what I did wrong. I connected the rca to video out instead of in, lol. Thanks again for a great video! Saved me a total of $425 labor only with the radio installation and purchasing their $110 back up camera. I bought a camera on amazon for about $35 and the radio with harnesses and trim kit about 260 :)

There’s two screws underneath the glove box that loosens up the glove box enough that makes it way easier to thread the wire to behind the radio. You don’t have to take the glove box off though. Also if you pull out the large plastic tray where a spare tire is typically kept making it easier to thread wire through back compartment to passenger door.

These actually did come with a backup camera on the JDM version as an option. Shocking for 2005. I was trying to look into what that set up/wiring configuration was like.

Thank you so much I will do that to my car I have the same vehicle , you work very professional thanks

how long was the video cable (feet) from the rear to the front of the car deck

First of all, excellent video. I was able to install my camera with no problem because of you. I'm just confused about one part about hiding the wire. I can't figure out how you went from 12:07 to 12:08. After you connect to the reverse light, how are you getting to the wheel hub ?

What wires do I connect to be able to use the factory revbrse camera with my new Android stereo. There is no rc input plug to go into stereo one.

Very helpful video. I’m trying to put the same backup camera in my 2006 CRV. I am wondering where you got the grommet used on the drilled hole in the rear door where the camera wires come thru?

@Jack : I'm a bit confused how you fed the spliced wires (that feed off the 12v from the backup bulb circuit) through the grommet. That things got such precise holes cut into it for the specific wires that exit the vehicle. Any chance there is a way to splice into them inside the trunk after removing the rear trim panel?

Very helpful. However, you did not show the placement of the camera installed and if the view was off not being exactly centered. I have a 2004 CRV (a year older than yours) and where you pointed was not centered, how does it view once installed? also where you pointed rt of the license i have a hole so that would leave left of the license plate on that ledge. My camera maker said, it would throw off the camera that was too far from center. Your thoughts? They suggest the only spot would be the bumper, do you have direction on taking off rear bumper? Done some searching and have found none. Thank you.

The green with black stripe is the positive. Can I use either 2 black wires for negative?

Hi! Thanks for that video, very well done! Would you please tell me what's the brand & model of the camera you bought? or maybe an URL to the product? Thanks 🙂

Very helpful video. Having a visual on the grommets did help. I have the same vehicle and just completed a license plate cam install. Although you drilled a hole...... we're curious on how you actually mounted your camera. I will upload a video of mine soon.

Hello and thank you for the video. I have the exact same crv as yours in the video. Toady, I spent the better part of the day installing my back up camera and radio. I was able to follow your video and remove the necessary trim pieces to get the wire to the front dash area where the radio is. Unfortunately, when I put the car in reverse, no video on the monitor. I tapped into the green and black reverse light wire with the red wire, which has the black wire connected to it. I grounded the black wire to the frame. Then I tapped red wire from the main long wire into the positive power feed wire as well. At the radio, my unit clearly displays which wire in their harness is for the camera, so I tapped into that wire with the red wire and plugged the yellow rca video into the back of the radio. What am I doing wrong? Thank you.

Found it... Thanks...

Hi I’m trying to connect an after market stereo in my Honda CR-V 2002 I got harness matching all the colours but still is not turning on. I did not understand clearly about the blue wire that you changed. Do you think that’s my issue?

Where can I buy the product his using?

Hello, thanks for the great video. I have a 2006 CRV. I plan to install a stereo-Nav unit with backup camera. Can I ask you what camera you used. I like the small end on the one that you used. Thanks

How did you route the camera wires from the back door to the radio? Under the carpet? Over the head liner?

Hello, im installing a camera my self, can you please tell me which wire Coming out of the reverse light is the one you connected.. thanks!! Green and black?? And solid black there's 2 of them

With the placement of the backup camera, are you able to see the spare tire? Does it block part of the view?

good job thank you!

Hello there! I am just wondering how it was when you attached the camera with the tire on. Does the tire affect the view of the camera? I have the same car pretty much so I am just curious.

help i use the green and black wire but the camera doesn't work

Hi, I installed that camera to my 2006 CRV. But my picture onmy screen is up side down. I noticed that 1 cable has to be cut in order picture will be correct. Please help me which cable I have to cut?

DID NOT SHOW THE FINAL FIT OF CAMERA OF THE DOOR

why not just go through the roof lining. Its so easy and takes 5 mins

i cannot get the wires through that tubing connecting the back door to the rest of the car to save my life!

Where can I buy this camera? Is it the same with that one on Amazon: amzn.to/2Gr9K44

Soo when you are reversing and you see on the camera the car/wall behind the car, you know that the first thing hittng it will be the Spair wheel yes?