2007 Chevy Cobalt Transmission Line Replacement

Рет қаралды 11,852

4 жыл бұрын

How to change the Transmission Lines/Hoses on a 2007 Chevy Cobalt. Shows the Quick Disconnect fittings on the radiator. Had some odd sized Quick Disconnects that I ended up reusing.

Пікірлер: 26

@xelaju8 3 жыл бұрын

Thanks for showing all the parts with plenty of light. Also, thank you for mentioning all the tips and troubles that you had. That helps us a lot.

@TheOutwiththeold Жыл бұрын

Yeah, I just had to do this on a 08 Saturn same thing the dormans were not the right part for the fittings, I had to go to Napa and spend $22 each on those quick disconnect fittings NAPA part number is 730-5740.

@TheOutwiththeold Жыл бұрын

Transmission Connector M18x1.5

@RADMAN752 4 жыл бұрын

i like the way you did this video, took your time to show every step and get things out of the way. sometimes its better to take the time to make room rather than to maneuver around hoses and curse and swear. if you do maintenance on your own cars you know what i mean. make it easy on yourself. thanks!

@raabsand 3 жыл бұрын

Excellent video. Very informative

@survivormary1126 4 жыл бұрын

Good camera shots. I think you made a lot of extra work for yourself to get them, so thanks. Taking shroud on bottom off was a total waste of time. You could definitely edit this and shorten it up. I think you should have jacked it down flat while filling, then jack it back up to put plug in. Sealed system should have right level. Thank you!

@cutwormsmith 3 жыл бұрын

Bravo.... Very thorough. I'll be doing this job soon. 👍

@johnfechter3317 3 жыл бұрын

Very detailed, thank you!

@brandoncook6383 4 ай бұрын

If those lines were leaking would it cause my transmission to shift incorrectly or not at all because pressure is off?

@survivormary1126 4 жыл бұрын

I cut my lines with a sawzall after trying all kinds of disconnect gadgets and not being able to get clips out. Black cap helps put pressure on the clip to keep it in.

@rogergcm 2 жыл бұрын

Great video. Very informative. I was wondering if you know if the o-rings in the trans are replaceable. Mine is leaking from the bottom line at the trans. I don’t think changing lines will be the fix for this. Thx.

@fdesimone6611 3 жыл бұрын

Do you ever find the correct connectors? If so, what size and where to buy? I’ve been looking as well and can’t find the same. O ring seems like only option unless you found something

@jimdandy6472 3 жыл бұрын

No, never found a replacement quick connect fitting, but the original ones have not leaked a bit.

@danlacy4588 2 жыл бұрын

Im unable to find them as well for a saturn ion. The lower one is in bad shape... Anyone know where I can find one..

@NRASUPPORTER1911 3 жыл бұрын

Sir does it need to be running to check the transmission fluid i just want to make sure thank you

@jimdandy6472 3 жыл бұрын

It does not need to be running. If you have dropped the pan and changed the filter, or had to installed new transmission line hoses it would be a good idea to add about the right amount, start the car and let it run for say 30 seconds in park, and then shut it off and do the final fill with the engine off. With the car level, and the threaded high level plug removed, pour transmission fluid in until it starts running out, and then put the plug in. Don't get overly concerned about a quarter cup one way or the other, there is some slack built into the design.

@NRASUPPORTER1911 3 жыл бұрын

@@jimdandy6472 I changed the transmission cooler line on my 08 Chevy hhr and I warmed it up completely put it on a lift and while running I pulled the check plug and it poured out a lot like it was overfull so I let it drain about a quart out until it was seeping out! Will more come out when running I thought when they was shut off all the oil came down to the bottom that’s why I left it running I’m just worried I drained to much!

@NRASUPPORTER1911 3 жыл бұрын

And can I ask another question the little nut that tightens against the transmission cooler lines you think I should tighten until it stops turning?

@jimdandy6472 3 жыл бұрын

@@NRASUPPORTER1911 It's not uncommon to find that someone added too much transmission fluid to a system without a dipstick. With about the right amount of fluid added, run the engine and with your foot on the brake, cycle the transmission through the gears so that fluid is in all of the internal passages, coolers, hoses, tubes, etc., and then back to Park and shut the engine Off. Then, with the car fairly level remove the fill plug. A small stream of fluid should come out. If not, the fluid level is low and thus add until it starts to trickle out. I don't think it would make much difference if the engine was running at idle, but I could be wrong. Many people get overly concerned about having the fluid at the right temp, the car perfectly level, and running or not, but +/- a cup is not a big deal. I say check with a dealer, but I do it with the engine off.

@jimdandy6472 3 жыл бұрын

@@NRASUPPORTER1911 Yes, tighten until it obviously pulls things together and gets tight. It's pretty small, so don't go crazy, but just a bit of torque, like 15 ft-lbs.

@tyshordee5323 2 жыл бұрын

How many quick connects did you have to replace

@jimdandy6472 2 жыл бұрын

Ended up being none. Never found a replacement quick connect fitting that fit, but the original ones have not leaked a bit. If they ever leak, I'll just replace the O-rings inside them.