2008-2014 WRX manual transmission replacement
Рет қаралды 34,479
Күн бұрынHow to remove and install a transmission on a Subaru Impreza WRX. If you need to do a clutch, and flywheel, you could watch an earlier engine rebuild video I have on this same vehicle. STi is the same job, but they have a 6 speed. This is a 5 speed. 2009 2010 2011 2012 2013 08 09 10 11 12 13 14.
Playlist of Nicks other work can be found here
• Nicks 2012 WRX engine ...
Disclaimer:
Due to factors beyond the control of Rust Belt Auto, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. Rust Belt Auto assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Use this video at your own risk. Rust Belt Auto recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of Rust Belt Auto, No information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained.
@kevinghiandoni1889 4 жыл бұрын
Wow ! I’m glad I found this video ! I’m removing my full drive train today and I gotta say it’s a detailed video and you’ve shown it step by step! Thank you !!
@RustBeltAuto 7 ай бұрын
You're welcome.
@andrewknutson91 Жыл бұрын
Hoping I don't have to replace my trans in my 14 WRX anytime soon but if I do, I will surely watch this video again. Loved every second of this video and I laughed throughout. Way to put some humor into a really tedious job. Subscribed! Cheers, sir.
@Owensti 6 ай бұрын
Very detailed and explanation of everything, recently picked up a 2011 Wrx Hatch. Went to pull the motor and the trans came with it, previous owner failed to mention he took off the trans support and bolts so I had no idea how they mounted or went or anything so this video helped out so much.
@tommygomez5343 3 жыл бұрын
Thank you so much for taking the time to record and upload this video. I'm in my early 50's and I'm replacing the manual transmission in my son's 2008 WRX. I referenced this video several times while removing the transmission. I made the mistake of not strapping the engine down like you did in the video. I couldn't figure out why it was getting hung up even after I had the transmission and engine separated about 2 inches. Anyway I will be picking up the replacement tranny in a few days. I ordered a clutch kit for it, but we are getting the factory flywheel resurfaced. I'm not sure sure about the cheap lightweight flywheels that come in these kits. I will get back to you when it's completed and back on the road. Thanks again. Cheers and Beers!!
@RustBeltAuto 3 жыл бұрын
Getting the clutch lined up is the fun part. Good luck!
@edwardrerekura3264 3 жыл бұрын
everything about this video was perfect thank you man i did a clutch replacement with this guide line video alone best video i came across
@jonahcollyer8165 3 жыл бұрын
This is exactly what I've been looking for! Thanks super helpful!!
@MiggySalami 4 жыл бұрын
Thanks for the informative video! I need to replace the clutch on my 2011 wrx. Subscribed!
@RustBeltAuto 4 жыл бұрын
Good luck!
@swandonny 7 ай бұрын
Your accent saved my life
@RustBeltAuto 7 ай бұрын
🤣
@E3N_Bierski 2 жыл бұрын
Bro your word choice is GOLD!
@isaachess8990 4 жыл бұрын
Love it 😂 doing my 08 wrx hatch
@zackcollins5642 10 ай бұрын
Getting ready to pull the transmission back off of my manual swapped 92 SVX (manual is from an 09 STI)
@mattsmith9159 3 жыл бұрын
Great video man helped heaps
@migueleguigure4837 4 жыл бұрын
Awesome thanks for the video it’s going to be a big help to me I have a 15 sti that I need to change the clutch and other advice you can give
@RustBeltAuto 4 жыл бұрын
Welcome! Exedy clutch/pressure plate, resurface flywheel. Best advice I can give.
@aihcgnay9724 4 жыл бұрын
Thanks for the video. I need to switch the transmission on my 2010 subaru too.
@RustBeltAuto 4 жыл бұрын
Welcome. Good luck!
@livalittle100 4 жыл бұрын
Great video!
@86753091974 3 жыл бұрын
12:41 'nuff said thats what i needed to know, thx
@Saidy29 Жыл бұрын
Hey what type of clutch is in those Wrx. Is it push or pull type
@BarnStangz 4 жыл бұрын
Dude and I forgot to ask, when are you going to get your old Jonda on the YT again, aren't you going to turbo that baby?
@chrissandler2 3 жыл бұрын
Are all four of the driveshaft bolts weighted? Do you need to mark the exact location of where each bolt came out of on the driveshaft? Thought I read somewhere that something to do with the balance of the driveshaft and the balance can be thrown off if things aren't put back a certain way.
@RustBeltAuto 3 жыл бұрын
The bolts are the same.
@tommygomez5343 3 жыл бұрын
Did you use any lubricant on the input shaft splines to make the installation easier? If so, what did you use?
@RustBeltAuto 3 жыл бұрын
A very small amount of Honda urea grease if you feel it's necessary. Splines should be dry.
@KillaZamii 3 жыл бұрын
Question: when I did my clutch the throw out bearing did not have those springs holding it to the clutch fork. We were confused so we just reinstalled the new clutch without the bearing springs. Was that bad? What can happen without the springs?
@RustBeltAuto 3 жыл бұрын
Maybe nothing? A lot of other manufacturers don't have those. I doubt it will go anywhere. Maybe keeps it from rattling? If your whole world ends, let me know.
@Charlie589 3 жыл бұрын
That's the external wastewater making that noise also with the turbo. Back fires cause of the gasing, shifting and the tune, runs perfectly fine. Nice video!
@gitarooman2995 2 ай бұрын
It was a joke dummy
@2011WRX4ME 2 жыл бұрын
Can you reuse the axle nut or did you put a new one on? Thanks for the video. It's a great reference for my STI.
@RustBeltAuto 2 жыл бұрын
I reused them. The dealer might tell you to replace it.
@2011WRX4ME 2 жыл бұрын
@@RustBeltAuto so do you just rehammer that part is bent down to lock it in place?
@RustBeltAuto 2 жыл бұрын
@@2011WRX4ME yes
@fame0609 3 жыл бұрын
Same thing happened with my wastegate from tial
@skylineplaya44 4 жыл бұрын
Good video
@RustBeltAuto 4 жыл бұрын
Thanks!
@iamchrisdammit 2 жыл бұрын
Tool. 🤘 yes!
@tacoselhuequito7019 4 жыл бұрын
What size of a stud puller did you use ?
@RustBeltAuto 4 жыл бұрын
I cannot remember, and have a set that goes from 6mm to 12mm.
@leovelazquez4349 2 жыл бұрын
Do you have to do an alignment after replacing the trans?
@RustBeltAuto 2 жыл бұрын
No.
@davegwilliam7352 Жыл бұрын
Did you reuse the studs or replace them? Was there a particular method you used to torque them back down?
@RustBeltAuto Жыл бұрын
I reused them. You can torque them to whatever Subaru recommends, they have no sequence on the bell housing as far as I know.
@davegwilliam7352 Жыл бұрын
@@RustBeltAuto thanks. This was a beast and a half to get back in but we got it thanks to this video.
@jasonlopez6441 Жыл бұрын
I have the upmost respect for this man🫶
@vrbonzani 4 жыл бұрын
I have to remove my trans on my 13 because my throwout bearing is screaming. Saw a tsb for the clutch fork causing the issue. Do I have to take the turbo out to remove the transmission? The nice thing is I just did a turbo about 20k miles ago and every bolt got a nice coat of anti sieze so I should be golden. Any advice you can give me would be well appreciated!!
@RustBeltAuto 4 жыл бұрын
You can leave the turbo in.
@vrbonzani 4 жыл бұрын
@@RustBeltAuto will I need to pull a vacuum on the clutch after I put the trans back in?
@RustBeltAuto 4 жыл бұрын
@@vrbonzani you should not nees to do anything with the master or slave fluid.
@vrbonzani 4 жыл бұрын
Got a question for you. Have guys had problems with bell housing bolts breaking off when removing them? I'm in the middle of pulling my trans on my 13 wrx and 2 bolts have already snapped off inside the block.
@RustBeltAuto 4 жыл бұрын
@@vrbonzani they were probably overtorqued. Maybe too long. I have yet to snap one on a subi.
@JR_Diesel 2 жыл бұрын
Where do you live and how much do you charge for this? I have a ‘13 wrx!!
@RustBeltAuto 2 жыл бұрын
Outer space. Everything is free.
@chaviechav656 2 жыл бұрын
Did you have to remove the shifter itself? From the inside of the car?
@RustBeltAuto 2 жыл бұрын
Did you watch the video? I forgot.
@crazyDIYguy 6 ай бұрын
Aren't those 6 speed Subaru transmissions strong AF? I wonder how he did that?
@RustBeltAuto 6 ай бұрын
Race car ya ya.
@adamgooch930 4 жыл бұрын
i’m not able to shake my transmission back into place:/ still got .25” of gap and it won’t moveeeee
@RustBeltAuto 4 жыл бұрын
Is it an even 1/4" all the way around?
@jasonruiz6738 4 жыл бұрын
You did a great job but I think the engine is on backwards that’s why it backfires
@RustBeltAuto 4 жыл бұрын
Lol... I would have never guessed. I better turn it around for him.
@JDMreck 2 жыл бұрын
My friend I have a 08 sti hatch 6 speed any ideas if is a pull pressure plate or like the one you have push pressure plate
@RustBeltAuto 2 жыл бұрын
I do believe those are pull plates. If you want to know for sure, call the dealer, or parts store, and use your VIN#.
@JDMreck 2 жыл бұрын
Ok is because my 08 sti hatch is at the shop and they told me is a push plate not a pull plate 😑 I'm a little upset because I feel like that they haven't touched my car I remember having a bugeye and it was pull plate any ideas why? Is the 08 same as the 02
@RustBeltAuto 2 жыл бұрын
@@JDMreck i don't know.
@JDMreck 2 жыл бұрын
@@RustBeltAuto thank you for replying I'm gonna go to their shop tomorrow if they haven't touched the car I'm gonna send a tow truck and just do it my self I did the bug eye is just that I dont have time now the I own a business I have to b there most of the day
@RustBeltAuto 2 жыл бұрын
@@JDMreck i do know that this car I worked on had a different clutch and transmission hor an STI the same year.. good luck.
@tommygomez5343 3 жыл бұрын
Hello, what stud remover did you use to remove the 2 bottom transmission bolt studs? Do you have a link to the stud remover?
@RustBeltAuto 3 жыл бұрын
MAC TOOLS SR4MA Metric Stud Puller Set. That's the set I have. There are many more like it.
@BarnStangz 4 жыл бұрын
It's nice to see you keep moving up in the sub count man! This was a good video! I figure the way this kid hammers this Subie, you'll have plenty of content from it! How are you liking Filmora? OKAY BYE!
@RustBeltAuto 4 жыл бұрын
I'm trying to like it.
@BarnStangz 4 жыл бұрын
@@RustBeltAuto There are a few wonkey things, but for the most part, it's pretty solid. Is your PC pretty beefy?
@RustBeltAuto 4 жыл бұрын
@@BarnStangz My PC is not made with any beef, or free ranged chickens.
@BarnStangz 4 жыл бұрын
@@RustBeltAuto OH yeah, caged chickens! Makes me hungry for some Chick-Fil-A! DUDE, make sure you have at least 16GB of RAM, Filmora likes it!
@SB-me6qw 4 жыл бұрын
Scale of 1-10 how much does it suck to do this with out a lift?
@RustBeltAuto 4 жыл бұрын
You will be working on those 6 pack abs.
@SB-me6qw 4 жыл бұрын
I guess that couldn’t hurt. Cheers
@srichampootv 3 жыл бұрын
What suspension are you running for your lift? You should make a video about your lift kit!
@RustBeltAuto 3 жыл бұрын
Max jax twin post.
@srichampootv 3 жыл бұрын
Rust Belt Auto oh sorry I meant on the subie. Is the Subaru lifted? Or was that lift that was making it looked lifted?
@RustBeltAuto 3 жыл бұрын
@@srichampootv yes the lift lifted it. Gotcha!!!
@nixl3830 4 жыл бұрын
Do u have to disconnect the shift fork?
@RustBeltAuto 4 жыл бұрын
Unbolt slave cylinder?
@nixl3830 4 жыл бұрын
Rust Belt Auto that's all I have to do?
@RustBeltAuto 4 жыл бұрын
@@nixl3830 Why do you think you need to remove the shift fork? To change the throw out bearing or something?
@edwardrerekura3264 3 жыл бұрын
love the humor also
@armandocelaya4752 2 жыл бұрын
ur amazing.
@RustBeltAuto 2 жыл бұрын
Oh really!?!?!?
@erwinmorales2862 2 жыл бұрын
Where are you located
@RustBeltAuto 2 жыл бұрын
Outer space.
@JoeyG4L Жыл бұрын
Where do you get a putty knife
@RustBeltAuto Жыл бұрын
The putty knife store.
@JoeyG4L Жыл бұрын
@@RustBeltAuto literally
@rockyking2595 3 жыл бұрын
Ur a God dude 😂😂
@RustBeltAuto 3 жыл бұрын
Ooh really!?!?!?!?!?!?!?
@jonathanfonseca2906 3 жыл бұрын
Man did this In sandals
@RustBeltAuto 3 жыл бұрын
did this in sandals too. kzfaq.info/get/bejne/fcqVardo1NzcpI0.html
@ethand5672 3 жыл бұрын
FYI that drain plug is a t70, had to go buy specifically that one socket because nobody has it in a set lmao
@RustBeltAuto 3 жыл бұрын
I think I would use an air hammer and a chisel, before buying a t70. But that's just me, because I'm kind of a cheap hack. Fortunately, I haven't been forced to buy one to use it once or twice on a Subaru.
@ethand5672 3 жыл бұрын
@@RustBeltAuto haha cheaper form e to buy the socket since I don't have a chisel/air hammer xD
@tylerasbrock4782 3 жыл бұрын
This seems like one of the simplest transmissions swaps ever
@RustBeltAuto 3 жыл бұрын
Done old GM 350 turbo's in an hour. Did a manual in a Porsche once in about 1 1/2 hours.
@giovannirevilla2638 3 жыл бұрын
This guy hates aftermarket LMFAO!! So do I🤣 pointless
@RustBeltAuto 3 жыл бұрын
Hate is such a strong word. I prefer to use disdain.
briansmobile1
Рет қаралды 109 М.
Grays Garage
Рет қаралды 12 М.
The One Place
Рет қаралды 7 МЛН