🙂. Did the video help you repair your vw vehicle? What year & model are you working on?

🙂. Did the video help you repair your vw vehicle? What year & model are you working on?

These cars with all the computers and sensors can be aggregating.

Because the pulley is literally cutting the sensor. if you hear something hitting, is that. so, or you have to replace the pulley or try to figure out where the pulley is touching the sensor.

I replaced mine and it still doesn’t turn on. It does the same click noise it did before e

@@franka6680 I notice that noise when I reassembled the pulley (I been doing timing belt). And the noise come off when the sensor broke up.

@@DKGARAGE_FL I was told it could actually be the starter. Since the car won’t start and the sensors can’t compute any cam rotation when you scan it it’ll give you a cam position sensor code. But ima try to see if this is true

@Dana-ro5gj .. After getting the ODB II code P0340 .. which P0340 is an OBD-II diagnostic trouble code (DTC) that indicates that the powertrain control module (PCM) has detected a problem within your Jetta’s CPS circuit .. caused by an issue with the wiring harness going to the camshaft position sensor (CPS) or the camshaft position sensor itself.

The gear is the only mark that is important. The belt can be moved around so don’t use marks on the belt for reference. The mark on the cam gear must line up with the alignment mark on the metal back plate. The engine must be at TDC (Top Dead Center) on #1.

Greg, are you getting any OBD2 codes? Those sensors are more likely when you’re having a misfire. Does it run fine at idle? Just coming off idle it stalls? A 2012, so probably lots of miles. Have you checked fuel injectors, try fuel injection cleaner with only 2-3 gallons of gas in the tank (makes it more concentrated). If it gets better? Do this several times. Maybe replace injectors (WARNING $$$$). You replaced the coil pack… did you replace plugs and wires? I’d also look at cleaning the intake and sensors… the computer is making fine adjustments all the time, so even the O2 sensors on exhaust adjust the fuel at the injectors…. And will make the engine run roughly and lose mpg…the catalytic converter will get red hot and exhaust is stinking… So just a few of my initial ideas… greg let me know how it goes..take care.

When I first bought my used 2013 Jetta it was having the same problem. It will stall out when slowed down to lower speed. Ran fine at higher speed and idle good. I replaced the crankshaft sensor and never got the problem again.

@@thoeuthsrey4494I had a bad Key Fob that set off the immobilizer which caused the same issue

Yeah that can be a problem…. This car is manual transmission so we removed the right front wheel … screwed a few lugs back on and put transmission in gear….and using a pry bar turned the axle…which then turned the engine..

That just seems like so much to do is there and easier way?

Ima try it though

Engine was skipping and my son replaced the plugs, wires, coil pack and it was still missing. We replaced the easy (and less expensive) parts first.

The misfire and running poorly even after replacing the plugs, wires and coil pack.

Sound’s more like the crankshaft sensor for no start…. Camshaft might also be bad too, but it would probably still start and just run poorly.. Good luck 👍

It will misfire and have less power… so yes.

Not sure on your first question what you are asking… yes lefty loosely…

@@Teds_Garage I figured it out. So I did the sensor. Finished the job codes never came back but the car still didn’t start. After a few days my friend got a second opinion and was told her engine was seized which to me makes no sense cz it was running before it went bad

@@franka6680 engine is seized = will not turn over. So if you are getting the starter to turn the engine it is not seized. If the crankshaft is turning then it is not seized…. Now it could still have a more serious problem but not seized.

You don’t like the selection of music? Or you don’t like any music?

Did you check your timing belt? A broken belt or if tensioner goes out it can jump and get timing out.

Slowly turning the ignition to start…ie on and off to get the engine close until you can see the mark. Remove the spark plugs and the engine will turn easier…. Turn the engine at the crankshaft to get the markings aligned. It requires a special tool… that fits your crankshaft. VW has different types over the years and different engines so get the right tools. You need to check your auto parts store for if they have the tool and some places will rent/borrow the tool for the day. I didn’t have the tool….so.. Otherwise…Carefully pulling on your alternator belt and don’t pinch your fingers… with spark plugs out it will turn… You should be removing the camshaft bolt to get to the camshaft position sensor. To hold the camshaft/engine from turning while removing the camshaft bolt: I put the car in gear (manual transmission) and it locks the engine. If you don’t have an impact tool, use a tight fitting wrench and tap the end lightly with a hammer…. Don’t get too aggressive…. they used a “lock-tight” and just a slight tapping will get it to release. If you have an automatic transmission - first try the tapping method above. If still stuck you hold the crankshaft to remove the camshaft gear bolt. This requires a special tool… that fits your crankshaft. VW has different types over the years and different engines so get the right tools. You need to check your auto parts store for if they have the tool and some places will rent/borrow the tool for the day. If not (not recommended) you can use a wrench/wood wedged into the alternator belt to hold the engine…. But be careful not to damage the alternator pulley or belt.

It could… cam sensor tells computer when to send signals to the coil pack. So older engines had points and a distributor cam lobe to signal the spark. This modern engine uses cam sensor and crankshaft sensor to signal timing (and adjust timing when running). You may have other problems though… see if cam belt broke (look behind the plastic cover if it’s turning), if you are getting spark at the plugs (also consider coil pack), with plugs out are you getting compression (if it’s a mechanical failure)?, etc.. I had one car with security issues … when the key was inserted it was supposed to disable security… the same key that had worked for years… the engine still turned over but wouldn’t start.. You would think security would disable the starter, but no…😣 So it could be a lot of things and can be hard to isolate… start with pulling the plugs and check for spark.. Good luck..👍

Sounds more like a crankshaft sensor for no start condition. But it could be the camshaft sensor.

Also thanks for the info. Dealing with this right now. Great info

Maybe with ohmmeter/multimeter, and a VW garage with their expensive computer… Not sure on the pin out though but if you have a oscilloscope you could see the signal….

@@Teds_Garage thanks for your input. I got someone to crank it for me while I inspected and the crank was turning but the cam was not. Pulled timing belt and the teeth on the belt had broke off. New belt and water pump and am good to go!

Glad to hear you got it fixed and going again..👍

Sorry but I don’t understand what you’re asking…?.

The screw * of the crankshaft because mine turn when I try😅

The camshaft? or the crankshaft? You should be removing the camshaft bolt to get to the camshaft position sensor. Either way I put the car in gear (manual transmission) and it locks the engine. If you don’t have an impact tool, use a tight fitting wrench and tap the end lightly with a hammer…. Don’t get too aggressive. I think they used a “lock-tight” and just a slight tapping will get it to release. If you have an automatic transmission - first try the tapping method above. If still stuck you hold the crankshaft to remove the camshaft gear bolt. This requires a special tool… that fits your crankshaft. VW has different types over the years and different engines so get the right tools. You need to check your auto parts store for if they have the tool and some places will rent/borrow the tool for the day. If not (not recommended) you can use a wrench/wood wedged into the alternator belt to hold the engine…. But be careful not to damage the alternator pulley or belt.

If you’re sure the timing belt is good and you have compression. Do you have spark at all your plugs? Coil pack could have died.. and is much more common and easy to replace. If all the above is good then maybe look at camshaft sensor.

Were you able to fix P0016 code I have same issue but mine one starts with a little extra cranking and checks engine light pops up on every start, clear the codes while engine running no issue, restart engine again same code. How did you fix it?

I even replaced the camshaft position sensor still same issue