www.williamsmobileclutch.co.uk 🇬🇧 Contact us for your clutch replacements. Thanks K-A. Williams.

As an avid mechanic I can say, This is one of the best mechanical channels on KZfaq. Simple, on the point and great video quality. Thanks for the great content.

pleasure to watch you work. Smooth movements, every single ste well thought through. Deep respect for the hard, work. back when i was young i did many jobs w/o lift or pit, but definitively have to bow to you.

Great work Kev, appreciate all the time and effort you put into all your uploads 🙌🏻 long may it last fella👍🏻

A good view when fixing the friction plate Good job as always. Thank you

Kevin, I thanked you before but having just tackled this on the drive, I must thank you again. Knowing ahead of time details like how high to raise the car, gradually compressing the o/s driveshaft cup back in [it felt like it wouldn't go], the gearbox angle when dropping it down and your technique for solo manhandling it back up/in [bloody heavy!] was invaluable. Trying to work that last one out with that lump of steel & aluminium resting on my chest would have been a nightmare. Not to mention the risk of damaging the new clutch if you get it wrong. Thanks again.

Sou da área de manutenção automotiva, só de você jogar o câmbio no peito igual faz, já vale o LIKE!!!! Parabéns!!!

Congratulations for your work 👏🏼

Great video again Kev. I have used your videos as a guide when I changed my MINI clutch. I also replaced the gearbox bearings. I chickened out of lowering the box on my chest though 😂.

Clutch Ninja! I've watched a few of your A3 vids now, ahead of tackling the job on the drive. Your great camera work has given me a heads up on potential issues. The time and effort you've put into showing us how it's done is very much appreciated, thank you.

I havent fitted a clutch for years since my apprentice Citroen days back in the 90s. Newer cars just phase me but after watching this video, im keen to give it a go. Cheers

Super boulot

Good to watch, good job

Mighty job there.

Excellent video, superb instruction, clear concise !😉

hello, I went through Google to send you this message because I don't speak English 🙂, I wanted to thank you for your work it's excellent because you make us see everything. I have a client who would like me to change the clutch for her on an Audi Q3 2l 140, and seeing all your videos I feel capable of doing it but I'm hesitant. I have already changed clutches but on French brands.

Good job! nice and beautiful . 👍👍

Great job 👍👍...All VAG's are the same,just intake plastic's are diferent 😉...

Hi Kevin - I've followed many of your drive way clutch changes and was inspied to undertake one on our Peugeot 2009 207 1.9 GT thinking it would be similar to the other 207's - now I know why we haven't seen a 207 GT being done :) lots of dismantling of top and bottome end bits to get to the clutch but we got there in the end...;)

what a machine William friends

a small tip for ppl i see struggle with those clips on sensors and such. Push inwards the plug and push to lift the lock Thus the plastic lock clip lifts up by itself easier.

Good job keep up

Hi Kevin just wanted to say a big thank you for doing my Audi you have done a FAB job you no your stuff mate trust me if anybody asker's your the man PS you are a very nice person got time to talk by the way video is great Al the best mate and thank you

Hi Kevin great informative video as allways. Love the close up shots. What make tool are you useing to centre the clutch plate please? All the best Matt. 👍👍

Hi long time but good see you still up to it have not been seeing much as i lost my son about 6 months ago so keep up the good work and see some more thanks nigel 🏴󠁧󠁢󠁥󠁮󠁧󠁿👍

Dual mass flywheel very cool 👍

Good job..thank you

What tightening torque do you use for the planetary screw? I saw that you do not use a torque wrench. Are the screws tight enough?

S-line very nice, and that gets a thumbs up from me buddy👍

Muito bom!

Hi, great video helped me do same to my car except I encountered an issue. Bought whole set in which dmf was exactly same as the old one but clutch plate and pressure plate are different looking. Now clutch feels light under foot, pedal don't bounce back fully and i can't put catlr in gear. Could it be those different type of clutch making issue? Tha K you for any response

Great video, everything covered and without stupid music and pointless chit chat 👍🏻

What clutch do you recommend for a Hyundai i30 1.4 petrol, model 2010? I don't know who is the original producer for it.

Encore un super taf que tu fait sinon j'aurez 2 questions pourrez tu me donnez la référence et la marque de ton cardan que tu utilise ??? Et aussi quel genre d'outils utilisé tu pour enlever les cosses car j'ai pas très vue ont aurai dit comme un tournevis encore bravo à toi car c'est vraiment du travail d'art que tu fait encore bravo👏👏👏👏👏👏👏👍👍👍👍👍👍👌👌👌👌👌

Why did you remove the driveshaft cups? Wondering... Thanks

In un'audi c'è un sacco di lavoro .per cambiare volano frizione e spingidisco .💪 buona domenica

good job/

Amazing work, i can tell that a lot of work went into this video. You took the time and effort to film every little detail. Thank you a lot! Little question: aren't the DMF bolts supposed to be torqued down to 60Nm +90°? Or it doesn't make big difference?

Do you use 1/2" drive all the time?

Hi, is this the same for a 2015 2.0 tdi convertable? Haynes say you have to remove the sub-frame!!

Great video as always, may I ask why you put grease on the bell housing bolt holes?

😎👍

Roughly how much does it cost to replace and fit new DMF + Clutch Kit on a 2009 Audi A5 2.0 TDI (6 Speed Manual) ? Clutch judders when moving off from first gear or if stationary in traffic and if clutch is held for too long the car starts to move by itself and clutch gets into this half stuck position. You seem to know exactly what your dealing with. I'd like to know if you can also come to Cambridge?

Awesome Video man, i have 2 Questions, did you use new bolts for the pressure plate? And i see alot of people saying you need to use Special equipment for the SAC Clutch to preload it before putting it on, my Set arrived few days ago and im gonna swap it tomorrow, and my pressure plate isnt Preloaded, but never have i seen a mechanic preload it with special equipment, what do you think?

Hi Kevin, I have a B7 Passat similar gearbox! How do you jack up the car so high! I have 15 VW Passat TDI tips or showing how to jack for clutch replacement would be great preferably on Audi/vw product

Buenas tardes, excelente su video. No obstante hacerle una critica a la marca alemana Audi: El diseno tan adsurdo y por demas complicado tedioso para cambiar el embrague.

👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻👏🏻

is there any cars you refuse to do gearboxes on simply because of how long they take or how much messing about it is to get the box of?

Hi kevin be interesting if you created content like this showing the fault with the Engine clutch first then showing it working after repairs

🤝👍✊👏

What fluid is that that you are adding back into the gearbox near the end of the video? Is it just the gearbox oil? Amazing video helped me with my own A3 massively! Keep it up

🇵🇹 👌

👍👍👍💪💪💪

🤗🤗🤗...!!!

11:58 is it necessary remove this part ? Why you remove it from grarbox ? At the week i will do the same ;) i need small support :)

🙂💪👍

What was that yellow dust in the engine compartment?

Hi Kevin. It's been a while... Correct me if I am wrong, but I think that u could let the right axle in the ball bearing - no need to undo the big screw. Only unmount it on the gear box side (the 6 screws) + the flange in order to take the gear box out. Of course you need to undo the bottom 3 screws that hold the lower arm attached to the wheel nuckle, in order to be able to push the inside part of the axle away from the flange. Or maybe u could get away even without undoing the 3 screws from the lower arm at all? What say U? Could be a bit of a time saver...

Greetings from Bosnia, can you tell me if a special tool is absolutely necessary for installing the pressure plate or can it be done like you do, just tighten the screws

Just had the full kit changed on my audi a3 quattro 2011, prior to before getting changed I noticed the car is still vibrating noise on 1500 rpm? I thought it was the dual mass vibration noise but it’s clearly not that. Any idea what it could be. 🙇🏽‍♂️

Just a quick one, how would a lightened dual flywheel on a Volkswagen Golf 2.8L V6 4MOTION Mk4 2002? 02M gearbox. I use it as a daily driver. It has 185k km original clutch. I would like to mate it with a Luk clutch. Thanks in advance.

Could really do with this doing on my 2013 Audi A3 2.0 diesel , Manchester ?

what model this makita tools?

I've done everything Kevin did in this video but separately so I know how long/difficult it is if you're not skilled as he is

What size are the clutch plate bolts?

👍👍👍👍👍💪💪💪💪💪👌👌👌👌

5:50-6:15 There is a problem with the sound.

🥇👨🏻‍🔧🇬🇧🍺