Thanks for the video. Other similar videos have poor lighting and skip around. Showing it all In a single clip makes it so much easier. I also went back and fixed the 90 degree on the piston as I was unaware of this before and grateful you mentioned that
@AaronD7112 жыл бұрын
I have to say this is one of the best videos for this job that I have come across. The only thing I'd add to it would be to clean the hub where the rotor mounts and the piston of the caliper and the opposite side where the pad sits. Nice job!
@faustogonzalez83972 жыл бұрын
Great video, exactly what I was looking for. Keep up the great videos.
@kimhoeunchhay4295 Жыл бұрын
Glad to hear it!
@aquaman01672 жыл бұрын
You made this look very simple. Thank you for taking the time to make this video.
@anthonycoffey94123 жыл бұрын
Helped alot 🤙
@robertmiller16383 жыл бұрын
Very helpful. Thank you!
@kimhoeunchhay42953 жыл бұрын
Glad it was helpful!
@michaelosullivan382310 ай бұрын
Great video just what i needed Thank you🎉
@kimhoeunchhay42959 ай бұрын
Glad it was helpful!
@Escobar80s Жыл бұрын
Great simple video. Thank you very much
@kimhoeunchhay4295 Жыл бұрын
Glad it was helpful!
@rayal63242 жыл бұрын
good job!
@rose1875911 ай бұрын
I changed my brake pads 2021. How often to change this pads?.
@ReloadFactory3 жыл бұрын
Thank you!
@vk6xcj2 жыл бұрын
Hi can you use a g clamp to push brake cylinder back in??? Do you need the special tool to screw it back in?
@kimhoeunchhay42952 жыл бұрын
we need special tool
@ramiramitto96792 жыл бұрын
thank you sir
@davidgardner65762 жыл бұрын
Can just Turning caliper make it go in or is that tool needed for force
@kimhoeunchhay42952 жыл бұрын
My tool use to turn and force the same time
@cyhassinger8654 Жыл бұрын
Leaving caliper hang by the hose is a big no no & no blue medium strength thread locker on the caliper bracket bolts?
@kimhoeunchhay4295 Жыл бұрын
Thank you for let me know my mistake u are the best. Thank you for watching
@404SRT3 жыл бұрын
What’s the part number for the pads/anti squeal shims?
@kimhoeunchhay42953 жыл бұрын
Part number is 04946-02050
@SDMF50003 жыл бұрын
Do both rear pistons wind in in the same (clockwise) direction? Or is the other side anti-clockwise?
@kimhoeunchhay42953 жыл бұрын
Hi SDMF_1 How are you ? Rear both caliper pistons have to be the same direction. Thank you so much for watching my video. Thank you kim
@SDMF50003 жыл бұрын
@@kimhoeunchhay4295 Thank you.
@lllmaurlll2 жыл бұрын
what tool is that, that squeezes in the caliber?
@Nonamenofame2602 жыл бұрын
You can find a similar one at Harbor Freight called: Disc Brake Pad And Caliper Service Tool Kit. Cost is $49.99 at the moment.
@S4LeagueCSKing15 ай бұрын
What's the name of the tool?
@machacek06212 жыл бұрын
Thank you Sir.
@kimhoeunchhay42952 жыл бұрын
You are most welcome
@erickrzyzanowski92322 жыл бұрын
My boot came off the piston and is broken. No store has the replacement boot. Do you know where I cab find one? I'm in Rochester ny
@kimhoeunchhay4295 Жыл бұрын
Replace new caliper is the best way and fast. i think online is available for repair kit Thank you for watching
@denislopez48372 жыл бұрын
When I change the break pads is necessary change the discs?
@Boss-3132 ай бұрын
No, you only change discs if they are worn, warped or severely scored. But you do need to change the pads every time you change discs.
@marklance033 Жыл бұрын
9:06 The boot ripped on mine. Can I replace it or?? Not leaking fluid
@kimhoeunchhay4295 Жыл бұрын
You should replace caliper that boot ripped sir to prevent dirt and water get in caliper piston. After you replaced new caliper please bleeding all air out from caliper.
@nguyenxuandongphuong2 жыл бұрын
Hi . I am doing m brake pads replacement for m 2014 corolla now, and I need the special tool to turn and push caliber in . Can tell me what is that tool name and where can I get it, please Thank you