224 Valkyrie Rem 700 Build: KRG Bravo Stock, TriggerTech Special Trigger (Part 6)

Рет қаралды 39,838

Күн бұрын

Full Story: bit.ly/2OdOiyY
Playlist here on KZfaq: bit.ly/2ESk7hp
My Precision Matthews Lathe: bit.ly/2SFJgNU
My Precision Matthews Mill: bit.ly/2VyeCYB
Time to install the TriggerTech trigger and KRG Bravo stock, which will bring together this custom 224 Valkyrie Remington 700 bolt-action rifle! Make sure you check out the full write-up (see link above). In the next story, I'll address the magazine issue.
-------------------------------------------
Ultimate Reloader LLC / gavintoobe Disclaimer:
You alone are responsible for the safety of yourself and your property.
Check local and state laws before undertaking any activity involving possessing, transporting, and shooting firearms. Check local and state laws before attempting to load ammunition or perform any modifications to a firearm. Always abide by the law. Always practice gun safety.
The content on this channel (including videos, ammunition reloading data, technical data, comments, and any other information contained within) is for demonstration purposes only.
Do not attempt any of the processes or procedures shown or described in this video or on this KZfaq channel (gavintoobe).
Any reloading data supplied on this KZfaq channel (gavintoobe) or in this video, including any comments from viewers and readers must be assumed to be in error.
Always consult at least three sources of manufacturer's ammunition reloading data before reloading your own ammunition.
Do not attempt to repair or modify any firearms based on information found on this KZfaq channel or in this video.
Gunsmithing procedures should only be performed only by a licensed gunsmith.
Ultimate Reloader, LLC can not be held liable for any harm caused to any individual or any personal property related to activities, procedures, techniques, or practices described in whole or part on this KZfaq channel (gavintoobe) or in this video.
By watching this video in whole or in part, you agree that you alone are solely responsible for your own safety and property as it pertains to activities, procedures, techniques, or practices described in whole or part on this KZfaq channel (gavintoobe) or in this video.
-------------------------------------------
Ultimate Reloader LLC / gavintoobe Material Connection Notice:
The following Ultimate Reloader partners are featured in this video:
- KRG
- TriggerTech
- Benchmark Barrels
- Precision Matthews
Ultimate Reloader partnerships involve one or more of the following:
Product supplied for evaluation + testing + features in videos/articles, paid advertising and promotions, engineering and product development services, scientific testing and evaluation, external media production and related marketing services.
Ultimate Reloader LLC is committed to publishing subjective and data-driven information+insights related to products whether it be favorable or unfavorable or both.
For more information about Ultimate Reloader partnerships, please visit: ultimatereloader.com/about

Пікірлер: 62

@chrisb9478 7 ай бұрын

I’m a retired LE Firearms instructor & armorer. I learned something valuable from this video. I really liked how you “seated” the action in the stock and gradually torqued the action screws. Nice. Makes sense. Thanks! 👍🏻

@Millennial_marksman 5 жыл бұрын

Keep this series alive! Ultimate Reloader could have a spin-off shirt that says "Build. Load. Repeat."

@Ultimatereloader 5 жыл бұрын

Yes, lots more of these stories coming :)

@tjarmand 5 жыл бұрын

gavin I love your videos.. plz never stop making them...

@Ultimatereloader 5 жыл бұрын

Thanks!!!!!! No plans to stop in the next 10 years :) :) Thanks for subscribing!

@kab5275 Жыл бұрын

Man, you are living the life.

@coyotiess 2 жыл бұрын

Nice video!

@holden3083 5 жыл бұрын

Hope the build works great. Stock costs au$750 so not cheap in Australia

@posjoey 5 жыл бұрын

Almost identical look to my rifle! Same stock and trigger! Mine is just in 6 Creed! Awesome video series, can't wait to see how it shoots!

@Ultimatereloader 5 жыл бұрын

Awesome- how's the 6mm Creedmoor treating you? I'm planning something- already have the Starline brass. Perhaps a RPR barrel conversion???

@posjoey 5 жыл бұрын

gavintoobe I'm a big fan of the 6 creedmoor. Got 107 smks going 3150. If I do my part it will shoot .4 - .5 moa. I get repeatable and consistent impacts out to 1200 yards. Just got some ADG brass and Barnes 112 match burners in. Gonna see how those two components get along. I find it a little more difficult to hand load for, 6.5 seems easier. But I'm not the most experienced reloader. Hope you do get a 6mm, I love to see your results!

@WestDesertShooter 5 жыл бұрын

Man it’s impressive all these videos turn out so great with perfect intros and outros. I know it can get confusing making multiple videos at one time remembering what you have and haven’t said for each video. Like my 1200 Yard Milk Jug Challenge I totally forgot to do an intro haha oh well. Great work as always! Curious to see how it shoots!

@northman77 3 жыл бұрын

Nice build! I have a remington 700 in 308, bought a triggertech trigger and a KRG bravo chassis. I had the same trouble for the front screw and came up with the same solution. I didnt had any spacer on the buttstock, I build it last winter and its cold here so I had multiple layer on me anyway but now I just get used to it even in the summer. I will had a strike eagle next month... I will take a look at your videos! keep up the good work.

@texpatriot8462 2 жыл бұрын

Could you do an affordable "custom" hunting build with appropriate stock, barrel nut barrels, affordable action for those of us without access to machine shop tools?

@Ultimatereloader 2 жыл бұрын

Sounds like a great project- we will put that on our idea list!

@dan34246 4 жыл бұрын

I'm completely new to long range shooting, would I need to get bottom metal for a barreled upper if I get this stock? Say I buy a factory tikka t3x lite that runs their proprietary mags, would I be able to remove it from the stock and be able to just plop it down into the KRG and run AI mags? And thanks for running through your build process! Makes everything look a lot less intimidating.

@knutpohl339 5 жыл бұрын

Awesome video series! I learned a ton. And it was entertaining. Thanks a lot for it. One question: why didn't you glass-bed the barreled action into the stock? Isn't that always preferable?

@Ultimatereloader 5 жыл бұрын

Thanks! This chassis is machined so that you don't need to glass bed- so far so good on that!

@johncook3265 5 жыл бұрын

@@Ultimatereloader I was wondering the same thing re: bedding. I'm quite uninformed in re: bolt guns though. Thx for answer.

@Cristopher1976 5 жыл бұрын

Does your bravo have an aluminum or polymer bolt release? If its polymer which extension did you purchase? I'm considering the bravo and read on their website for an August 2018 update they switched to a polymer mag release

@MCSPT117 4 жыл бұрын

Does the KRG Bravo have a metal DBM floorplate/trigger guard?

@biggerbehindthetrigger2814 5 жыл бұрын

That's going to be a very nice rifle when your done. I can't wait to see your groups at the range. What distance are you building it for?

@Ultimatereloader 5 жыл бұрын

I'm planning to go to 1000 yards and beyond! Thanks!

@biggerbehindthetrigger2814 5 жыл бұрын

@@Ultimatereloader good luck with your new tool.

@TommyboyGTP 5 жыл бұрын

Take it to a mile!!! @@Ultimatereloader

@paulvenn4447 5 жыл бұрын

Bench blocks are your friend :D Also, did you blueprint the action at all? Are you going to lap bolt lugs as well?

@kineticU 5 жыл бұрын

What magazines are you using for the 224 on the bravo?

@precariousbyte 3 жыл бұрын

Try actually watching the video. Then maybe check out part 7

@charleshetrick3152 5 жыл бұрын

Have you compared Trigger Tech triggers against Huber Concepts’ triggers?

@Ultimatereloader 5 жыл бұрын

Nope! I do plan to do TriggerScan comparisons in the future however!

@charleshetrick3152 5 жыл бұрын

I’m not familiar with “TriggerScan”, I have three rifles running Hubers and they’re ridiculously perfect. I brought it up cause I was looking at Trigger Tech for my ARs but after talking with a trigger tech employee I got the impression that set to their lowest resistance I’d be in jeopardy of a negligent discharge. Huber specifies they’ll pass the FBI’s rough handling test. Any how keep up the good work.

@jesseguzman378 5 жыл бұрын

Great build how much money are we talking about

@Ultimatereloader 5 жыл бұрын

$550 - barrel blank, $100 bolt mods, $400 stock, $100 extra parts, $40 scope rail, $200 trigger - so say about $1500 + labor + optics at the end of the day??? I gave myself a great deal on the gunsmithing labor :) :)

@stevenl7878 5 жыл бұрын

@@Ultimatereloader Wow, that's an expensive barrel for a blank. I figured the barrel blank would be cheaper than an already reamed/threaded barrel. My 223 REM Match Criterion was only $300 and it was ready to bolt on.

@beachboardfan9544 5 жыл бұрын

Cant imagine putting anything but a jewel trigger in a bolt gun, why'd you go with the triggertech?

@Ultimatereloader 5 жыл бұрын

Discussion with Jesse Redell from RBros - the Jewell is great, but I wanted to try something different, and this trigger is awesome!

@robertturnbull2903 5 жыл бұрын

I really like my trigger tech special.

@imbored742 5 жыл бұрын

I've got a TriggerTech on my AR and it's fantastic. When they say zero creep they're not kidding.

@jimhans1 5 жыл бұрын

Beach&BoardFan I own a lot of Jewell triggers, for both my bolt guns and my AR15s, they are phenomenal triggers for sure, but I also own a lot of Triggertech triggers for my bolts and ARs also. But I went with the Triggertech Diamond Model triggers for my bolts instead. They are all great quality triggers whether you choose Jewell or Triggertech, you can’t go wrong with either!

@mapled3135 5 жыл бұрын

What’s are you talking about? Trigger tech red blows jewel away.