6.9 7.3 idi diesel injection pump repair in a bottle

Рет қаралды 11,003

Жыл бұрын

In this video I show you a trick the old timers used to lube up the injection pump on a ford with the 6.9 or 7.3 idi diesel engine. this trick is a good idea after a truck sat for a long time. or if it is stalling and dying on deceleration or between shifts when you let off the throttle. classic symptoms of a stuck metering rod. Hit that 👍 thumbs up before you take off. Really appreciated by this small youtuber trying to beat the evil algorithms and get information out to more people that can use it. Check out the following links for more #idi #diesel videos.
What to look out for when buying a used 6.9 or 7.3 idi diesel part 2
• Buying a 6.9 or 7.3 id...
What to look out for when buying a used 6.9 or 7.3 idi diesel part 1 • BUYING a Ford 6.9 or 7...
7.3 idi race truck build part 1 tearing down the crash test dummy
• 7.3 idi diesel race tr...
How to bleed air and prime a 6.9 or 7.3 idi diesel fuel system
• Bleeding air out of th...
Replacing power steering lines in my 6.9 idi
• 6.9 idi ford truck pow...
Ford shower head fuel pick up to fuel sump
• Fuel sump install bull...
Ford fuel selector valve replaced with brass 3 way valves
• ford fuel tank selecto...
3g alternator swap to upgrade your old externally regulated alternator • Ford 7.3 idi diesel 1g...
Facet electronic lift pump installation
• 7.3 idi facet Duralift...
Where to plumb in and hook up aftermarket gauges to an idi engine (oil pressure, water temperature sender locations) • 7.3 idi diesel gauges ...
How to change 7.3 idi glow plugs • 7.3 idi diesel Ford e3...
7.3 idi manual glow plug button how to • 7.3 idi diesel glow pl...
7.3 idi fuel heater delete mod • 7.3 idi diesel ford fu...
Changing a starter in a 6.9 or 7.3 idi diesel • Ford 6.9 idi diesel du...
Reviving a 6.9 idi diesel by hotwiring the fuel shut off solenoid and doing a manual glow plug button • 6.9 idi diesel crank n...
Basic wiring to hotwire and start a 6.9 idi from under the hood
• NO KEYS NO PROBLEM! Ho...
Basic wiring to hotwire and start a 7.3 idi from under the hood
• Start a 7.3 idi diesel...
Diagnose and test a heater defrost system that is not coming on
• Troubleshooting and re...
Heat only blows on high DO THIS!
• Heat only blows on hig...
Check out these videos for more information on my #wmo #blackdiesel centrifuge set up.
5 ways to save $ setting up a waste oil centrifuge
• Waste oil to black die...
5 hidden costs to setting up a centrifuge
• Waste oil to black die...
First batch of black diesel ran through my wvodesigns centrifuge
• waste oil to black die...

Пікірлер: 146

@blackpowderandbibles Ай бұрын

You have brought me a new appreciation for these old idi's. Thank you.

@martinw9425 Жыл бұрын

That did the trick to my 1986 6.9 f350, i was wondering about my injection pump, my solenoid shut off , my my my??????? then i watch this video, i took ATF and filled my fuel filter.And it worked like magic...Thank you so much , now aint scared to drive around.

@worthshop Жыл бұрын

That is awesome! Love hearing from my viewers, knowing they are benefitting from the information I share. Keeping their trucks on the road.

@chrissybetts9434 22 күн бұрын

Thanks for the video... new to the world of 7.3 ....

@ingodwetrust1136 Жыл бұрын

I would love to hear a straight piped idi pass by my grave site everyday too lol 🍻🇺🇲 Awesome idi content and great advice, I use the ATF method aswell on my 6.9, works like a charm

@worthshop Жыл бұрын

Thanks for watching! Appreciate the comment, and God bless.

@dieselwrench3621 Жыл бұрын

Love the info and tips on this channel. Not many guy’s posting about the old IDI diesels. Keep those videos coming 👍🇺🇸

@worthshop Жыл бұрын

Thanks for watching, I will keep producing videos and trying to share what I have learned about these old diesels I love so much. Appreciate the comment, and God bless.

@DirectCurrent4u Жыл бұрын

I'm old school! I use one quart two stroke motor oil with every fill up on my 05 5.9 Cummins. Great video! Keep up the great work as always! Hope you have a great week. 👍

@worthshop Жыл бұрын

Alot of people swear by 2 stroke oil. If it works for you, it works for you! Thanks for watching, and God bless.

@DjeehBear Жыл бұрын

She's running great now! Blue Nose happy. ATF/DieselKleen are good combo. To that point, I had never tried 50/50 tho. I guess from lack of knowledge on how well ATF burns so I'd put 25% of fuel in the filter but seeing you going 50/50 makes me wanna try and I will do just this week because my filter is due for change. Thank you again for sharing your knowledge and experience. Keep buildin' shit!

@worthshop Жыл бұрын

No problem! I enjoy producing content to encourage others. Been judged and put down told I "can't" all my life. Once I overcame that mindset, and believed God made me for a purpose. It changed my life! Thanks for watching, appreciate the kind words.

@jamesdavis6275 3 ай бұрын

Ive filled my fuel filter up with seafoam before and didn't have any issues. Had alge in my tank . I have put atf in the fuel tank before because it lubes up everything and helps keep injectors clean

@strokedmule3838 Жыл бұрын

I’ve used diesel clean for years in both of 7.3 trucks, I’ve recently started using XPD. It’s not cheap but my trucks run smoother on it and get a little better fuel mileage. I run the diesel clean around for my normal driving but use the XPD for all my longer trips.

@worthshop Жыл бұрын

I have never tried XPD will have to get some and give it a try. Thanks for watching, and God bless!

@strokedmule3838 Жыл бұрын

It’s made by optilube, I typically get it through amazon.

@TheDeafMechanic Жыл бұрын

I’ve ran ATF and Diesel Kleen in my 6.9 86 F-250 the whole time I’ve owned it and it keeps it running great at 336k miles. Usually when I go to the junkyard I keep an eye out for random quarts of atf and new engine oil in old crappy cars and trucks. Makes for a great extra free fuel additive 🤣

@worthshop Жыл бұрын

Thanks for sharing! God bless.

@rickpaudert7012 7 ай бұрын

I like your videos bro: real life instructions!!

@worthshop 7 ай бұрын

Glad to help out! Thanks for watching.

@shannonc.4257 3 ай бұрын

I worked for a food processing company and have burnt veggy oil, cooking oil, sun flower oil, fish oil, used oil, etc. Diesel fuel was not a thing until Rudolf Diesel invented the diesel engine, he used peanut oil. Won't run on ATF is defiantly said by someone who does not understand how a diesel works. In the 1970's Mercedes 220 Diesel manual they suggest adding a half gallon of gasoline to the tank in the winter, for easier starting. I don't suggest you try this with any other vehicle, and the new diesels in general are not as friendly to changes as the old school diesels.

@jneidlinger Жыл бұрын

Hey bro! I love all the Ford IDI and WMO content. Been going back in your video history and watching a lot of them. Just wanted to shoot you a message and tell you thanks for all the educational videos. I plan on getting an IDI soon and getting into running WMO. I got a '02 Volkswagen Golf with the TDI engine that I plan on running a diesel/WMO mix and then plan on having the IDI setup with straight WMO in the one tank and diesel in the other. You should set yourself up with a way for your followers to shoot a few dollars your way to help you and your channel out! Thanks again.

@worthshop Жыл бұрын

Appreciate the comment. I never really thought about getting donations to help the chanel. Do it to spread info and encourage people to believe in themselves. I do have a paypal.me/worthshop is my profile. Had it several years. Maybe I should add it to my channel info again. Thanks for watching, and God bless

@jneidlinger Жыл бұрын

@@worthshop I don't know if this case is true for you or not, but I know some people get hung up on taking donations when you feel like maybe you (and your family) don't need them. And that's perfectly fine! But perhaps let people donate to help fund you with getting some better camera equipment which would help with putting out better content. Not bashing the equipment you got by no means either! You've done great with what you've got. But maybe think about it this way: better equipment to help you do the job more efficiently (maybe a tripod to hold the camera?), and at a higher equality (better camera so your viewers can see more details of what you're working on)

@worthshop Жыл бұрын

@@jneidlinger I just posted my contact info to my community section with a bit of back story. I did take some donations a few years ago to help establish a tool library, never did after that just for the chanel.. But I will keep my info up there and if people feel compelled to help out they can.

@tbobmann229 6 ай бұрын

New to idi..thanks for all this knowledge! Greatly appreciated!

@worthshop 6 ай бұрын

My pleasure 😊

@ProducersGroupProd 3 ай бұрын

Thanks For the Awesome info ! 👍

@MaxMiniTV Жыл бұрын

Great info, thanks!

@worthshop Жыл бұрын

No problem, good luck with your bus. Safe travels and God bless.

@ProducersGroupProd 5 ай бұрын

Sweeeeeeeeeet! Great Video! Keep em Coming 😊😊😊

@worthshop 5 ай бұрын

Thanks! Glad you enjoyed it.

@wutntarnation Жыл бұрын

What a great channel for aspiring diesel mechanics!

@worthshop Жыл бұрын

Thank you very much!

@JorgeHernandez-kc4gz Жыл бұрын

Thx bro! I’m gonna get this done, for sure..

@worthshop Жыл бұрын

No problem, thank you for watching, God bless.

@mikegurge4487 5 ай бұрын

Thanks Bud!

@worthshop 5 ай бұрын

No problem, glad to help out!

@josemartinez4680 Жыл бұрын

Good video, 6.9 are awesome

@worthshop Жыл бұрын

Pretty sure it was you that commented a while back that I should do a idi chanel. I didnt want to start a whole new chanel. But have been focusing on idi content and it is helping grow my chanel alot! Thanks for watching, God bless.

@Celzot 5 ай бұрын

You the man!

@worthshop 5 ай бұрын

Thanks!

@sanson57 6 ай бұрын

Me and my 1985 F250 4x4 6.9 idi International we are happy with your recommendations on usign ATF oil but I pour directly in my diesel tanks everytime I refill them to avoid removing my diesel filter so ading like 16 fl oz or so of ATF oil per 10 or 15 gallons of diesel works just fine, thanks again and keep posting videos👏👏👏👍👍

@worthshop 6 ай бұрын

Heck ya! Glad it's working out and your enjoying keeping an old idi rolling.

@unholy7324 9 ай бұрын

my man. i just bought a 93 f350 centurion last week and shes got a craptastic idle. it stalled a couple times on the drive home so im going to do an oil change, and fuel fliter change tomorrow and ill try this because youre the 2nd person ive seen suggest it. im loving your channel dude and i thank you for teaching me the 7.3 because this is my first ford and first personal diesel. i drove big trucks but i didnt learn anything pulling into a shop for someone else to fix it.

@worthshop 9 ай бұрын

If it is idling crappy and erratic, most likely getting air intrusion. Look around all the return line caps fuel filter fittings etc for moisture when it is running.

@unholy7324 9 ай бұрын

@@worthshop i did find one broken fuel line. it was on the fuel filter assembly. i trimmed it and stuck it back on the nipple. the oil is black as tar so ioll do the fluid change and while im under and in ill go over everything from the tank to the injectors. ill let you know!

@brendonmasters Жыл бұрын

Best channel on yt

@worthshop Жыл бұрын

I can think of a couple of my favorites, I don't feel like I even compare to... But I do appreciate your kind words! Thank you for watching, God bless.

@brendonmasters Жыл бұрын

@@worthshop have you ever done a video on fuel additives? I’m a dummie and I’ve done a lot of reading all over the forums. I’ve read about a litttle gas in the fuel and maybe a table spoon of bacon grease. Could you make a video dispelling any of these false ideas? Seeing as how you run your own fuel it’d be cool to see what else is laying around that could benefit these old hogs

@worthshop Жыл бұрын

@@brendonmasters I add about 20% regular gasoline to my cleaned waste oil mixture. Supposed to thin the oil and make it more flammable. I am not an expert by any means. Just follow the basic outline I have read about. Mixing waste oil with diesel is also pretty common.

@mattleonard5268 Жыл бұрын

Idi diesels like the 6.9 and 7.3 have hydraulic lifters instead of solid lifters like most diesels which means idi engines run less than great if they have dirty lifters or go too far on oil changes or use the wrong oil. Hope this helps! Thanks

@worthshop Жыл бұрын

Thanks for sharing, hopefully the info helps others as they cone along and read comments. Always appreciate people sharing their knowledge and suggestions. God bless.

@linctexpilot8337 17 күн бұрын

If it’s 15°F out, don’t rev your engine unless it has had the chance to warm the oil up a little bit

@mattleonard5268 Жыл бұрын

Marvel mystery oil works wonders on old diesels in the fuel and the oil!

@worthshop Жыл бұрын

I have used it a few times! Great product. Thanks for sharing.

@mattleonard5268 Жыл бұрын

2 stroke oil is the best I’ve found for lubricity additive in fuel for old diesel trucks

@worthshop Жыл бұрын

More than one way to skin a cat! I have heard alot of folks swear by 2 stroke oil. Just have not used it myself. Thanks fir watching!

@cucvfarmer 10 ай бұрын

Hotshot Secret EDT and or Hotshot Secret LX4 or Opti-lube Summer and Opti-lube XL.

@kman-mi7su Жыл бұрын

I've been running ATF in my 1988 7.3 for a while and I even put some in both tanks with the diesel. I wish I had a place to setup a system to process used ATF that I could run in my truck and save some cash.

@worthshop Жыл бұрын

It was not cheap or easy getting my centrifuge all set up, but definitely worth the effort. Hope one day you will be able to as well.

@beno.9958 3 ай бұрын

I'm interested in your collection and filtration system. Is it homemade?

@costasgeorgiou5015 2 ай бұрын

Yep! Black diesel! You filter it down to 30000 microns too?! 7:30

@kelkeep1467 3 ай бұрын

My 7.3 idi was doing a similar bucking occasionally. I replaced all the wet looking return lines and the wet looking hose from the hard line to the lift pump. Now the fuel filter isn't getting any fuel to it. I top off the fuel filter, it runs for a couple of minutes, and then bucks and stalls out, fuel filter down to about a quarter. Think it's a bad lift pump?

@robertkwiatkoski1292 8 ай бұрын

friend who has a 96 cummings said his uncle ( heavy equipment owner) said to fill the fuel filter with kerosene when changing it. Cleans the injectors.

@worthshop 7 ай бұрын

I've never tried it.

@mesothelioma5024 3 ай бұрын

Would this help a failing injector pump

@nickhodge2114 Жыл бұрын

When using WMO. Do you preheat before in jetting? Or do you mix with gas or diesel? I have 85 f250 6.9 idi. It's my one-day Truck. One-day it will be back on the road 😂☹️ no big cash flow. But I like the idea on WMO and what do you recommend for WMO filtering if no centrifuge is not available 😁

@worthshop Жыл бұрын

I heat my waste oil before I put it into the centrifuge so it cleans better, and helps evaporate off any moisture. I do not have a heater on my truck, but run 2 tanks one for regular diesel, and one for waste oil. I start uo and shut down on regular diesel. Only switch to waste oil for longer trips, once truck is warmed up. Usually mix about 20% regular unleaded gas into my used oil. Supposed to make it burn better and thin it. I do not add diesel, my used oil mix usually has diesel in it though. I have not experimented with other filtering methods. Basically jumped into waste oil diesel head first and set up a centrifuge. If I was going to do a cheap set up, I would do a series of filters and gravity feed through them. Start with a higher 50 micron rating then to a medium 30 micron then down to a smaller micron like 10 and finally through a 3 micron. Thanks for watching.

@dallasroberts6146 Жыл бұрын

Do these trucks always have that gray/white smoke coming out? Mine runs and starts awesome no problems. Doesn't loose any coolant or oil but it smokes lol. Did have the head gaskets done recently, right before I bought it. I'm the second owner

@worthshop Жыл бұрын

All diesels will have a little smoke especially at start up in cold weather. Alot of factors can go into how much it smokes. I would make sure your return lines are not leaking allowing air into the system. The previous owner may have turned up the fuel pump, could be slightly out of time.. Good luck with your project and God bless.

@jimschaffroth5652 Жыл бұрын

I put two gallons of atf and a gallon of Marvel to about a quarter tank once a year.

@worthshop Жыл бұрын

Great idea, thanks for sharing.

@thomaslockley945 Жыл бұрын

Is that a side tool box I like that any video of that

@worthshop Жыл бұрын

Truck is a dump bed and has a side mounted tool box on each side. I didn't do a video about them, they were on the truck when I bought it.

@nickhodge2114 Жыл бұрын

I have a 85 f250 6.9 IDI. If I do mix oil and gas. Like you are suggesting in a two tank system what do I need to do or adjust with IDI? Do I need to adjust the timing do I need to adjust anything with the injection pump??

@worthshop Жыл бұрын

You do not have to adjust anything, leave the timing where it is at. Make sure you filter the oil really good, or run it through a centrifuge to clean it before you put it in your truck. You start the truck on the tank with normal diesel. Let it warm up and drive the first few miles to get truck up to opperating temperature. Switch tanks to the oil mix. Drive a few miles from your destination, switch back to diesel tank. If you are only stopping at a store or whatnot you can leave it on the oil tank cause engine will still be warm when you restart the truck. You basically only want to run the oil once engine is warmed up.

@roadhousedelorean2630 5 ай бұрын

I just got my first diesel, 1992 f250HD 7.3 5 speed. Will this help a random 2 second surge while driving? It acts like I’m giving throttle while driving but only for about 1-2 seconds every once in a while.

@worthshop 5 ай бұрын

You are getting air in the fuel system "air intrusion"

@edp9811 4 ай бұрын

I added this to my tank and i think it destroyed my governor ring in my injection pump 😢

@christopherstidams3369 Жыл бұрын

Hey bub my 6.9 the fuel is gelled up it like -20 here in ky I went bought howes anti gel the grey bottle you have an white it anti gel to what do you do when your fuel gels ups

@worthshop Жыл бұрын

I never lived anyplace it got cold enough to gel my fuel until recently. I moved about 6 months ago to Eastern washington. It has been between 2 and 20 for almost a month now. Luckily For me the place I get diesel pretreats it. So it is treated with anti gel stuff before I even pump it into my truck. I put my black diesel adventures on hold until it warms up again so it is less risky as I learn.

@christopherstidams3369 Жыл бұрын

@@worthshop thank you for answering back am learning from ya awesome content bub

@nickhodge2114 Жыл бұрын

Oh and dose full synthetic oil work as WMO? I know a shop but they use nothing but full synthetic alf and engine oil.

@worthshop Жыл бұрын

I think the reviews on running synthetic oil are split. Some people say yes, some people say no. None of the oil I get is synthetic, all conventional. I work on a big farm and get all the old oil, atf, hydraulic fluid, etc from work. So I can't really give you a solid answer. I would try a small amount and see how it burns.

@ingodwetrust1136 Жыл бұрын

Do you have any tips on how to get a fuel return cap to stop leaking? I've tried different o rings and caps and she still wants to leak

@worthshop Жыл бұрын

I usually use Delphi brand return line caps, had good luck with them. Make sure you lubricate your o rings so they slide on easier and you do not tear them when installing. Alot of people swear by the return line kits sold by russrepair.com, but I am not the type guy to spend more on parts than I have to, so never used one of his kits myself. If you really want to spend some $ you can buy billet return rails from r and d idi performance. I have also seen a video from diesel tech Ron, he uses a copper drain plug washer on top of the return cap to tighten it up better here is a link to that video he mentions the washer about 12 minutes in to the video. kzfaq.info/get/bejne/adyhhsR1vMmnenk.html Hope this helps and good luck with your project.

@ingodwetrust1136 Жыл бұрын

@@worthshop Sweet thanx for the useful info, I have tried the kit from russ repair and it still leaked, I think I need to try the washer on top of the return cap method because I've noticed when the cap seats down it rises back up a bit and seeps fuel out the bottom, keep the awesome idi content coming brother 🍻

@scoieb Жыл бұрын

We have an 86 IDI non turbo. 123k miles. I towed a 1700 lb trailer and noticed a pinging noise only at freeway speeds. I do put low ash 2 stroke oil in the fuel. 1 once per gallon. What would make it ping at freeway speeds under a load?

@worthshop Жыл бұрын

Timing might be advanced a little too far.

@scoieb Жыл бұрын

@@worthshop thanks man!

@RIPFPSDOUG 8 ай бұрын

I lirterally just dump whatever in there all week long. gas and oil mix, waste motor oil, some atf, some diesel clean. Occasionally Ill dump in someoctane boost nitro too. The thing smells of sulfer and smokes to high heaven but she runs like a champ

@worthshop 7 ай бұрын

I got into running waste oil about a year ago. Saves me $ at the pump for sure

@KRev-nb7gc 7 ай бұрын

Is there a way to revive the injection pump if it's dead? My injection pump quit, and it won't start. Thanks in advance

@worthshop 7 ай бұрын

Time for a rebuild then.

@edp9811 9 ай бұрын

Do you know if deisel clean with brake down my olive seals? Chasing down a problem with my 6.9 idi after adding diesel kleen to my tank, found some debris in my injection pump after this

@worthshop 9 ай бұрын

I do not think diesel kleen is the one responsible for eating up olives all of a sudden. I think you probably already had old dry rotted or leaking olives orings etc.

@edp9811 9 ай бұрын

@worthshop thank you, been a crazy deal with this truck. Was perfect until I added deisel kleen

@alanchan1772 10 ай бұрын

I pour a tf each time I fill up my fuel tank,change filter I pour ATF

@worthshop 10 ай бұрын

Good choice! Keep that injection pump lubed up and lasting years to come

@edp9811 10 ай бұрын

Man I'm having so much trouble after adding deisel kleen, I'm sure it's a good product but just something with my truck... could you point me in any direction to figure out wtf is going on? Runs like crap, smokes real bad greyish white ish smoke, shuts off, no power, no throttle response, Runs like its missing, stalls when you take off, and I've replace the fuel filter twice. Pulled fuel from filter and 1 tank but it looks good Starts right up though but immediately runs horribly and doesn't want to idle at first You've been my go to KZfaq channel for all things idi, my truck is a 1984 f350 6.9 with only 51,xxx miles

@worthshop 10 ай бұрын

With the truck running when you push the shrader flvalve on fuel filter housing are you getting a good stream of fuel? Or is it weak? Alot of air and bubbles? Or clean fuel? Depending on those answers, I would try running the truck off a fuel jug. Hook a short hose to the lift pump on the lower passenger front side of engine. Run that hose into a gas can full of diesel. If it runs better, then your issue is between the tank and lift pump. If it runs the same, your problem is after the lift pump. That will start to narrow down the diagnostics. If issue is before, I'd suspect a bad pickup, a clogged line or sticking or plugged tank switch valve. After, probably air intrusion somewhere.

@hitnrun1805 11 ай бұрын

Have any videos of the fuel injector of an 7.3 idi taken apart and can they be put back together and reused or better going new?

@worthshop 11 ай бұрын

I do not have any videos of it. They are rebuildable. Not so sure it is recommended fir the home mechanic though because it requires special tools to pop test them and do it right.

@hitnrun1805 11 ай бұрын

@@worthshop I appreciate your response, I ordered a new one and hopefully am able to get it back up soon. Plan on making the trip west in this thing and seeing the sights! Maybe find your town too!

@worthshop 11 ай бұрын

@hitnrun1805 Supposed to replace as a set so they can be matched within a certain range of eachother. But I understand that is not always practical for some of us working on a budget.

@hitnrun1805 11 ай бұрын

@@worthshop yep, bought this set put them in about a year ago and 1 failed. Hoping it will get by for a bit.

@hitnrun1805 11 ай бұрын

I enjoy your videos and info very much!

@tZydeco Жыл бұрын

If you run usually WMO why did it need the injection pump repair from a jug?

@worthshop Жыл бұрын

I just set up my wmo system a couple months ago. Ran some through another truck. Then got the dual tanks working in this truck with brass 3 way valves to run wmo in rear tank and normal diesel in front tank. I am just starting to get to the point of running waste oil in this truck. Check out my videos the last couple of months for more information. It has been a whole process getting things set up and ready. Thanks for watching.

@tZydeco Жыл бұрын

@@worthshop - thank you. I've watched some of the previous videos but did not catch this idi was not on the new fuel.

@RickJamez05 8 ай бұрын

Question. Maybe you could help me out. I’m getting my injection pump replaced, as they are priming it they stopped because the mechanic said the pump picked up algae from the tank (truck has been sitting for 4 years) we are just going to replace the tank with a new tank. But my question is, is my injector pump ruined or is there a saving grace? Is there anything I can do?

@RickJamez05 8 ай бұрын

1994 7.3 turbo idi

@worthshop 8 ай бұрын

Shouldn't cause you any issues. I have ran plenty of old trucks with algae in the diesel. Your filter should have caught any chunks before it even got to the injection pump.

@kellycowett6254 Жыл бұрын

Staniydian is best for it

@worthshop Жыл бұрын

I will give it a test and see. I have always used the diesel kleen cause it is what my dad taught me, also because it is at Walmart and a decent price. I am open to trying other products though! Thanks for watching, God bless.

@thebear6751 Жыл бұрын

I’ve had great luck with standyne and diesel kleen

@kellycowett6254 Жыл бұрын

Staniydian is made by the people that built the pumps for the idi's it good stuff for cleaning injectors

@worthshop Жыл бұрын

@@kellycowett6254 Thanks for the suggestion. I will have to try it sometime.

@mudholemutilators9065 Жыл бұрын

I just run it on oil and atf

@worthshop Жыл бұрын

I just started getting into wmo recently. Should keep things lubed up even better once I run it regularly. Thanks for watching.

@kellycowett6254 Жыл бұрын

Do you have a way to get in contact with you other than your KZfaq channel

@worthshop Жыл бұрын

Robert Meader is my name on facebook, you will recognize me from my profile pic.

@Tycheese8 Жыл бұрын

I used too much diesel kleen in my 7.3 idi now no crank or start any suggestions?

@worthshop Жыл бұрын

No possible way too much diesel kleen leads to a no crank situation, unless you pulled injectors or glow plugs and filled the cylinders full then reinstalled. No crank is electrical, a starter, the starter solonoid, ignition switch, batteries, battery cables etc.

@Tycheese8 Жыл бұрын

@@worthshop appreciate you

@worthshop Жыл бұрын

@@Tycheese8 No problem, thanks for watching. Let me know what you figure out. Any more questions, just ask.

@Tycheese8 Жыл бұрын

@@worthshop possibly fuel injector pump?

@worthshop Жыл бұрын

@Tycheese8 No, if it's not even cranking it has nothing to do with fuel system. It is electrical issue

@jasontelly2218 Жыл бұрын

Someone told me to fill the filter with seafoam and let it clean ? What do you think would be better? My trucks definitely buckin 😂

@worthshop Жыл бұрын

I have never used sea foam. I can only advocate for what I know, use diesel kleen or atf. Hope it helps you our. Also bucking is usually more of a sign of air intrusion.

@jasontelly2218 Жыл бұрын

Thanks for the reply! And air intrusion to the fuel system? Like a leak or?

@worthshop Жыл бұрын

@@jasontelly2218 Yes

@dubious_donut 6 ай бұрын

Do not do this I did the exact same thing under advice and bent a connecting rid due to hydrolock.. new motor is now installed and will never listen to dum asses again

@dubious_donut 6 ай бұрын

To recap...Seafoam to n fuel filter destroyed my 7.3 idi

@davidshane272 Жыл бұрын

If someone says it won't burn oil or atf probably best to just skip over comment they don't have a clue about diesels I put old engine oil back in my tank and old trans fluid never had a problem

@worthshop Жыл бұрын

Truth. Thanks for watching, appreciate the comment. God bless.

@MaxMiniTV Жыл бұрын

Hey I wanted to send you Paypal but I think you have the paypal address wrong on your about page? I didn't want to guess and pay the wrong person for the great info you give. I have a question for you, too: In my '91 7.3 bus the fuel filter light comes on a LOT. I was changing the filter every time until I realized the fuel in it always looked clean. No gunk in the tanks. I've been just ignoring it since then, figuring the sensor itself was the problem, but is there anything else that could be wrong that would make that light go on? Thanks in advance if you get a chance to respond.

@worthshop Жыл бұрын

Dang thank you for pointing that out to me. Think spell check changed up my PayPal link. I got it fixed now. Paypal.me/worthshop is the correct link. Your fuel lift pump could be getting weak causing the filter light to come on. But if you are not having a loss of power when it comes on, I would agree with your thoughts that the sensor itself is going bad. Really appreciate the kind words. God bless.

@JeremySchneider-sq3so Жыл бұрын

When my truck is good and hot and i turn it off for 30ish minutes it won’t crank unless I pour cold water on the ip, would this help this issue????

@worthshop Жыл бұрын

@@JeremySchneider-sq3so No, you need a new injection pump. It is worn out.

@ericmuhlbeier8023 11 ай бұрын

Looks like wa state

@worthshop 11 ай бұрын

Yep!

@jonathanshaw5563 Жыл бұрын

You are doing a great job on your channel!! Employ a company like *promo sm*!!!

@worthshop Жыл бұрын

I have grown organically this far. If I succeed or fail on youtube doesn't matter to me. What matters to me is sharing information and encouraging people.