Finally started welding the driver side quarter panel.
Пікірлер: 48
@larryz249 жыл бұрын
You are a professional Sam you will make it shine no matter what....great update.
@ClassicCarOverhaul9 жыл бұрын
larryz24 Thanks Larry
@LILGIBBYPRR-ESR2 жыл бұрын
What is the metal Guages on oem panel? And what is Guage on aftermarket
@ClassicCarOverhaul2 жыл бұрын
Not sure, it's been so long ago. From what I can remember the guage on the aftermarket was close to the oem.
@RustyGlovebox9 жыл бұрын
The panel really came out looking good Sam. At first I was a little concerned but you got it working fine now.
@ClassicCarOverhaul9 жыл бұрын
Rusty Glovebox Thanks Lloyd, I'm still concerned but at some point I got to get these quarter panels welded and deal with what ever pops up next lol.
@69novaguy916 жыл бұрын
WoW ....I wonder why that stuff sets so fast .... well looks like you got it in there good .... I could imagine you had to fly when getting that where it needed to be .... I think we all get a little scared when it comes to actually welding in the panels .... Every thing you have done looks great .... That car is going to be better then when it rolled off the assembly line
@MrMach19 жыл бұрын
Yeah lol that stuff sets up fast! Looking good Sam!
@ClassicCarOverhaul9 жыл бұрын
MrMach12004 Thank you sir.
@Tanoble699 жыл бұрын
The panel came out really nice - looks good.
@ClassicCarOverhaul9 жыл бұрын
Tom Noble Thanks Tom
@265chevy9 жыл бұрын
nice work you are on your way now great work
@ClassicCarOverhaul9 жыл бұрын
265chevy Thanks Hanson
@Thisoldcar9 жыл бұрын
Thumbs up, great job your doing on the quarter panel Sam. Quit often you can put some Acetone into a tray or can and you can dip those caulking nozzles into the acetone and clean them up to reuse over and over. The nozzles are not terribly expensive but the cost does add up if you keep doing small bits of caulking from time to time over a project. Cheers OLDDUDE
@ClassicCarOverhaul9 жыл бұрын
Thisoldcar Thanks, I will try that acetone for those nozzles,
@damianlachapelle62929 жыл бұрын
That 64 looking real nice. I love them cars !!!👍
@ClassicCarOverhaul9 жыл бұрын
damian lachapelle Thanks
@Swilling9 жыл бұрын
I agree, committing to my quarters final placement was tough, you ain't kidding about the join between the deck filler and quarter, it's a bear to weld. I've also heard about some foams expanding too much and bulging the panel. Lookin good!
@ClassicCarOverhaul9 жыл бұрын
Swilling Yes that is a tough area to weld, thanks for watching.
@DoubleRRestorations9 жыл бұрын
I get trigger shy when it comes to finally welding it in place until I put down a few plug welds. Your right, it's going to be where it is and you will just have to work around any issues that may arise. That's the way I had to deal with that trunk pan. Panel looks great Sam.
@ClassicCarOverhaul9 жыл бұрын
Double R Restorations Thanks Russ, my wife say's I'm making progress now lol.
@TheRickfix9 жыл бұрын
looking good sam,thats some fast setting stuff,sparks will be flying now,welding that first piece in is nerve wracking but u r on your way now,hopefully the other side goes well too,take care and have a good one
@ClassicCarOverhaul9 жыл бұрын
TheRickfix Thanks Rick, I'm going to give that welder a workout now lol. Thanks for watching and take care.
@ziggassedup9 жыл бұрын
Weld 'er up mate..Poofteeths of an inch is nothing to be concerned about unless you're going for a show car..Ya done good mate.
@ClassicCarOverhaul9 жыл бұрын
ZIGgassedUP Thanks mate.
@Buckswoodshop9 жыл бұрын
Nice work.
@MrFireman1649 жыл бұрын
Lookin good sam , that foam is crazy fast , blew my mind cause I wasn't expecting it
@ClassicCarOverhaul9 жыл бұрын
MrFireman164 Yeah it's fast, after I watched your vid I was expecting it but still I thought I would have at least a minute or 2 lol.
@carylamari65469 жыл бұрын
Sam you did a great job, you are right at some point you just have to do it and deal with whatever pops up. It looks like you breezed right through any issues with this quarter. I hope you have just as easy of a time on the other side, I am sure you will do great and think about it, its down hill from here lol ;)
@ClassicCarOverhaul9 жыл бұрын
***** Thanks Cary, your right I've been messing with these darn things to long,. Time to get er done lol :)
@asicerik9 жыл бұрын
That is looking really nice Sam. I think that it lines up just about perfectly. What's left is probably just the aftermarket mismatch. Looks like a little clean-up around the door, but real nice everywhere else.
@ClassicCarOverhaul9 жыл бұрын
asicerik Thanks Erik
@huck019559 жыл бұрын
Looking good
@ClassicCarOverhaul9 жыл бұрын
huck01955 Thanks
@strokedfirebirdable9 жыл бұрын
Good job Sam. Call it being cautious :) The quarter from hell will be a piece of cake now.
@ClassicCarOverhaul9 жыл бұрын
strokedfirebirdable Yes Dave that's what to call it cautious, I'll be ready to tackle that 1/4 from hell now lol.
@ceedell9 жыл бұрын
Looking good Sam! I don't use the foam sealers, never liked how they work and always felt that was what caused the rust in the first place....just my thought. lol
@ClassicCarOverhaul9 жыл бұрын
ceedell You maybe right about causing it to rust, do you have any suggestions on what else I could use on those areas or would you just put nothing at all? Thanks.
@ceedell9 жыл бұрын
Classic Car Overhaul I don't put anything between the panels. On vehicles that will be driven I usually apply a little undercoating with a brush along the seam line in the fender well after all paint is done then use a spray bottle with a trans fluid/kerosene mix to squirt just enough for corrosion protection on any internal welds. Just how I do it.
@Fixinthatupvideos9 жыл бұрын
Yeah Man i Call it being Careful - T=up Sam
@ClassicCarOverhaul9 жыл бұрын
FixinThatUp Thank you sir
@slickpanther064 жыл бұрын
How can you tell if a 64 impala has had quarters replaced? If you don’t see spot welds under the quarter is that a red flag? What should I look for?
@ClassicCarOverhaul4 жыл бұрын
Where the wheelhouse welds to the quarter panel there should be spot weld there unless they are covered with filler. Another way would be if you removed your moldings and take close look at the holes where the clips mount you would be able to tell if they are original, the oval ones are stamped and perfect, the aftermarket quarter panels you have to drill and file them yourself and are difficult to get them perfect. If you don't have molding then another way would be the lower body line where it meets the door, the aftermarket panels are wider and the original ones are the same size as the back of the door then it starts to get wider as you go back towards the rear. Hope that helps.
@slickpanther064 жыл бұрын
@@ClassicCarOverhaul Thanks. This helps a lot!
@everettsamuel67798 жыл бұрын
What did you use to cut the quarter panels off clean
@ClassicCarOverhaul8 жыл бұрын
+Everett Samuel Not sure what your question is, are you asking how I removed the old quarter panel?
@everettsamuel67798 жыл бұрын
yes I need to remove mine but I don't want to cut into anything I'm not suppose to
@ClassicCarOverhaul8 жыл бұрын
+Everett Samuel I used a spot weld cutter to cut all the spot welds and air chisel to separate the panels. Have to be careful with the air chisel and work slow with it or you'll tear up metal that you want to keep. where the quarter meets the deck filler panel that seam has about 3 or 4 spot welds I had to cut out the top section of the quarter to get to those welds could not get to them from inside the trunk cause the trunk hinge boxes are in the way. Hope that helps if you want I can make a video showing what I did just let me know.