6g Test 6010/7018

Рет қаралды 1,487,715

Күн бұрын

read the full article on my website www.weldingtipsandtricks.com/6...
This is a 6g pipe test with 6010 root and 7018 fill and cap.
fitup was 30-35 degree bevel with 3/32" gap and land.
Root was welded with 1/8" 6010 electrode
Fill and cap were done with 7018
amperage settings and other details are in the video
Visit my store at weldmongerstore.com for TIG Fingers, DVDs, and other quality welding tools.
For even more options, check out my Amazon recommended products page at www.amazon.com/shop/weldingti...
Follow Welding Tips & Tricks on social media to see what I’m up to:
Instagram: / weldmonger
Facebook: / weldingtipsandtricks
Join the discussion with thousands of welders at the Welding Tips & Tricks forum
forum.weldingtipsandtricks.com

Пікірлер: 291

@ahmedeensaeed991 2 жыл бұрын

This guy makes all other welding Yutubers look like fakes. He comes across as genuine and caring.

@buzzwoodshop 6 ай бұрын

Absolutely 💯

@ryanjones9305 4 жыл бұрын

Thank you for showing the finished weld. There are those on here that like to talk about how to do it but never show a close up on the work when it’s done. Nice job welding and nice job on the video.

@saidfahmi9805 Жыл бұрын

Two years ago until now, and whenever I come across this video and I enjoy watching it, you are always brilliant. Thank you for this wonderful effort

@dariusacevedo6369 Жыл бұрын

just in time! that pro tip when doing the fill & cap with 7018 is exactly what we are facing, our instructor told us that we should always point our rod at the center of the pipe, but as we do that the bottom weld with the 7018 always sags, no matter how fast we do our travel, thanks for that!

@metalmeltingcanuck2467 2 жыл бұрын

Just passed my f3-f4 pipe today! i used the root technique from the previous root video. Thanks Jody

@kadehebert4054 4 жыл бұрын

Yal helped me pass my first 6010 rt 7018 2” 6g.... first attempt ever .... thanks for doin these

@odanestewart2169 4 жыл бұрын

Well done mate

@brym3452 4 жыл бұрын

I definitely enjoy you're videos more then those other channels tbh. Great stuff.

@getsmart3701 2 жыл бұрын

ISO 9606-1 weld tests allow the use of a grinder on the root string only. I don't know how it works job to job but the International test allows the grinder regardless of what the tester says. Know your rights guys, it can make a difference. Some great tips as usual Jody, they make the videos very rewatchable (depending on where a fella is on the learning curve)...and Andrew is a Jedi level pipe welder. Thank you.

@SteadArcFab_Ministries 4 жыл бұрын

Nicely done Andrew and Jody! Thanks for a all narrated specifics! Can’t believe there are any dislikes on these videos! Be blessed guys!!!

@Exit213 2 жыл бұрын

I am a welder. I studied for 3 years. But through your channel I learned a lot more than I studied in that period.

@metubewot 4 жыл бұрын

In my dreams I would be able to weld like that. Great Job filming too Jodie.

@FlexoBeatz Ай бұрын

I have weld test coming up for a job if I pass it I could be life changing for me and my family thank you for all the tips 🙏🏽

@adv.jeandersongusmao.7 4 жыл бұрын

good morning teacher! you are very good at coated electrode. I'm from Brasil-MT, the welding technology is exceptional. Very good my congratulations ...

@ianjoseph145 4 жыл бұрын

Excellent weld never easy using 1/8 7018. Keep up the great video's.

@brettbreza8815 4 ай бұрын

Love your weldmonger store awesome tips too

@Delossantos008 3 жыл бұрын

The bevel so clean very informative. Keep it up

@Rodelangbak23 2 жыл бұрын

Very nice. I've learned something on how to weld the 6g. I'll watch on ur next videos again sir💪💪💪

@ksingh1332 4 жыл бұрын

Respected sir these tips r very help for those who want to learn some extra tips for welding....bcos I'm a welder and building electrician

@deeessex4041 4 жыл бұрын

The one test I struggled with cause it was my very first time but now I feel determined ‼️

@weldingtipsandtricks 4 жыл бұрын

Good luck

@Laynethestain 4 жыл бұрын

Oh how I've been waiting for this

@juanimuscariello 2 жыл бұрын

Great master!! his ability is very remarkable !! greetings from Argentina.

@GeneralBoboDK 4 жыл бұрын

I am not a welder, and never will be... :) Tried it once, and it didn't go all that well... But man I love your videos! :) Never skipped once!

@razor2571 3 жыл бұрын

If you want to be a welder, keep trying. I'm sure you'll get better!

@HondaRacingHolland 4 жыл бұрын

I wish my weld puddle was that smooth this week! Currently welding tube’s and square’s in Swiss outside on a parkinglot with conarc elektrodes and basic machine, sticks barely start or get stuck, cuts out everttime 😭😂

@thelacker4766 Жыл бұрын

This is the greatest video I’ve ever seen

@paulmorrey733 4 жыл бұрын

Thanks to both of you

@albertbell7120 2 жыл бұрын

Hi Jody, from the age of 15 starting my apprenticeship only allowed to use hammer and chisel to cut back for root … as I progressed worked with a journey man who also taught me not to use the grinder very much as he always said we get paid for putting metal in not taking it out … we were on piece work then … the good old days 🇬🇧👍 Sorry forgot to say the weld looked very good smooth operator that’s what we get paid for.

@alvinlondonio8247 2 жыл бұрын

Thankyou for this kind of video ive learned a lot.

@dx63 4 жыл бұрын

Hello from Greece. That video are consignment for the new welder.

@learningtheoldschoolinthen258 4 жыл бұрын

Does the arc one thing come with the part that goes around your face to? Thinking about possibly building one myself.

@dwihardita7727 2 жыл бұрын

Great video...I watched this video many times👍

@robindrabishaw2170 2 жыл бұрын

Excellent video you guys sure know your stuff.thank-you.

@daveymatthews2251 4 жыл бұрын

Very informative Video nice work!

@Delossantos008 2 жыл бұрын

Can i ask what camera do you use for capturing root pass thank you sir and more power on you channel

@crazyryan2689 4 жыл бұрын

I'll be starting school in Daytona, FL in the fall for welding. Someone told me about your channel. I'd like to find some videos on beginners and what to expect.

@weldingtipsandtricks 4 жыл бұрын

Well I dont have any videos like that yet..but I would say expect to be by yourself for hours at a time welding. expect to be frustrated sometimes but just know that its normal not to make progress every single day. sometimes its 2 steps forward one step back...but overall you are still making progress. pay attention, learn the fundamentals, make sound welds first, then make them pretty. good luck

@CarlosRuiz99 3 жыл бұрын

Excelente muchísimas gracias por los típs 👍🏽👍🏽

@willmcpherson7953 Жыл бұрын

Ain't nobody beeping wit Jody on this welding tip💪💪💪

@dannywilsher4165 4 жыл бұрын

I welded miles and miles of pipeline back when I was a youngster. One job I was on in New Mexico I burned probably several tons of rod . We were welding a pipe that was 90 feet across and 3 inches thick. It was a mine shaft that went 600 feet into the ground. Quite an interesting job that was. Most of the welders were burning 1/8 rod and would take 12 hours or more to do an 8 foot section. I would burn 1/4 inch rod and do 4 - 8 foot sections in my 12 hour shift. All the welders hated me but the boss paid me 4 times what he paid the other welders. So I didn't care what they thought. We were getting paid by the hour but I knew the man that had the contract and he took good care of me. Fun, fun, fun.....

@purple935 4 жыл бұрын

You must of been a RAT welder..

@dannywilsher4165 4 жыл бұрын

@@purple935 Don't know what that means...

@htxsn9543 4 жыл бұрын

I always weld like that to. I can’t help it. I can’t milk a job , I only have one speed n it’s GO!

@MrFonsex 4 жыл бұрын

Lies

@madaxe79 4 жыл бұрын

Ahh you’re of those dogs that can’t work in with the rest of the crew. Word of mouth travels fast, guys like you rarely get consistent work.

@jomarseguyo3191 3 жыл бұрын

gifted hands...awesome welds!👏👏👏

@edrake1989 2 жыл бұрын

He has a very steady hand!

@mongomoko2322 4 жыл бұрын

Good and helpful video. Thank you.

@timothymckern8956 3 жыл бұрын

Did you do an episode on aluminum spool gun some techniques

@gulayaomj Жыл бұрын

Thank you for sharing this video...I have more learned about this welding this channel

@brittanyviafranco7909 2 жыл бұрын

Nice job both Jodie and welder

@hmmedina8299 4 жыл бұрын

Me gustan tus videos no podrías hacer una prueba 6GR? SMAW no hay videos de ese proceso estaría bien que lo hicieras saludos 🤟

@markhester5145 4 жыл бұрын

Great video! Good info

@StreamSideAdventure 2 жыл бұрын

Thanks for the video I feel more than confident

@hmmboy 4 жыл бұрын

Thanks for the education

@equinta8265 3 жыл бұрын

you are a great welder you don't need to talk much like others welding speaks for you

@JoseRodriguez-kz1yl 4 жыл бұрын

What size of 6010 rod hi is using for the root pass 1/8 or 3/32 some procedures require downhill root pass, thanks

@dirceujuliao7232 4 жыл бұрын

Fez o teste certinho . parabéns. Posição 6g tem o meu respeito.

@darleyvargas466 4 жыл бұрын

Exelente vídeo quisiera que hicieras uno en españo

@TheScottishCorsaBGuy Жыл бұрын

hey can you try rooting with a 8016-G rod 2.5mm and then 3.2mm 8016-G fill and cap?

@rodneybynum8104 3 жыл бұрын

I noticed your test video was welded up i see so many videos about downs and wonder why every time

@naga9575 3 жыл бұрын

halo weldingtipsandtricks. what brand of welding wire is used. for 7018 is ok 48.04 esab. right..

@marioserra4383 4 жыл бұрын

good tutorial, thanks

@raselbro4207 2 жыл бұрын

Nice wolding Bro

@abrahamanham 2 жыл бұрын

105 with the 1/8 7018? Seems kinda cold I’d be worried about leaving slag or a hollow head especially if after you grind your root it’s narrow. Any thoughts?

@piotrilczuk5663 4 жыл бұрын

Dziękuję pomocny materiał

@war16 4 жыл бұрын

Excelente vídeo un saludo desde Colombia 👍

@srkgamingiyi3645 Жыл бұрын

Nice video 👍

@kristineabelardo9671 Жыл бұрын

Good job sir andrew

@surjeet6453 4 жыл бұрын

Great job 👌👌 Thnks.. It will help me a lot

@krazziee2000 4 жыл бұрын

nice ,great lesson, thanks

@simonsiron887 Жыл бұрын

Hey man loved the video. I have a question for you. I'm 14 years old living in UK and I do blacksmithing and welding jobs. I want to start practicing open root in 3g and eventually pipe. But my little inverter can't run 6010. 6010 rated machines here cost at least 4 grand. My question is can I use a 6011 for open root joints like pipe and all that? Thanks for the help

@jeffsmith3941 9 ай бұрын

Hey brother I hope I’m not too late to help you. The short answer is yes you can run a root pass with 6011, the slag will be more difficult to get off and the arc won’t be as stable, it will however work.

@jcporosity4764 4 жыл бұрын

Great video i beem practice pipe in my garage cus school to expansive. I have gotten better even on my tig. Im not a pipe welder. I just want to learn the process

@mddelowar1873 3 жыл бұрын

Nice job

@josenildoandrade8431 4 жыл бұрын

Parabéns migão ficou top

@aldrinnavasquez737 Жыл бұрын

good job sir thank you for sharing

@DagoBoilermaker 3 жыл бұрын

Great work

@anisurrahaman5716 2 жыл бұрын

Thank you So much boss

@buzzwoodshop 6 ай бұрын

Love this vid!

@gianharrylazaro6442 3 жыл бұрын

Buen video Master 👏👏👏💪💪💪

@matthiasrodriguez2589 4 жыл бұрын

Hey ! Where can i find this pancake ?

@theyemeniwelder6310 4 жыл бұрын

Nice work

@soldadurascls1920 4 жыл бұрын

Nice weld 🤟😉

@dantebayron5509 3 жыл бұрын

Nice bos, GodBless!

@rudycesneros5122 3 жыл бұрын

hi, thank you and i salute to your job ,god Bless

@First-sj5mq 2 жыл бұрын

When I'm doing 6g with 6010, I always have undercut on the top of the bevel in a few areas. Rod angle is my issue but everytime I try to adjust my angle I still have the same issue if not something else like a crater or something like that. I run my amps at around 65-70 1/8th land and gap. Anyone have advice to help? Thank you

@niranbhujel2868 2 жыл бұрын

I'm pipeline welder watching from🇳🇵 nepal.. I like you

@travelwithme6434 Жыл бұрын

Your good teacher

@olddawgdreaming5715 4 жыл бұрын

Great job and enjoyed watching this.

@JORGE-SOLDADURAS 3 жыл бұрын

Quiero ver la pasada de raiz porque es la mas dificil. O le hiciste la padada de raiz con tig.

@richien4829 Жыл бұрын

The last line@ capping is not in your video..i can't see it..

@edisonmontero1861 3 жыл бұрын

Excelente! Felicitaciones

@MrHevyshevy 4 жыл бұрын

Thank you.

@akwild83 Жыл бұрын

6g was always my favorite test it's all positions in one, my welding instructor would always hound me to get comfortable before you start or it'll turn out like sh#!

@nizzurtmontalgizzert3337 2 жыл бұрын

One handed! Great skill

@razaligazi1146 Жыл бұрын

Fill and cap use 3.2 rod?

@Ab-bi7zx 2 жыл бұрын

Sick man 🔥🔥🔥

@ChiNguyen-wf1qt 3 жыл бұрын

Bought 6010 rod flux color is red. I only need 40 amp to weld 1/8 inches steel. And 50 amp to weld 1/4 inches steel. Any higher amp than that will burn through. Not sure if it's the rod or me. I was told I need 75 amp for 1/8 inches and 90 amp for 1/4?

@felipeteixeira1042 4 жыл бұрын

Fez esse teste com a máquina invertida ?

@stevedawelda9036 4 жыл бұрын

I miss the stick work been on the tig 4 years now!

@antoniotonio8776 4 жыл бұрын

Thank you is verry good this video

@saminyusubzade1439 3 жыл бұрын

What is the national distance to the root?

@sylvestresanchez4848 4 жыл бұрын

Thank you

@jeromeb5929 2 жыл бұрын

By no means am I trying to sound rude or saying anything negative but would that root have passed x-ray? Just asking

@marknorris5881 4 жыл бұрын

Jody, I've got one for you. 1/8" 6013 vs 7014, AC, for us wantabes. How they compare for the most bead length pound for pound-dollar per dollar. For our simple projects. "Thanks"!