Stick Welding Techniques 6010 Downhill

Рет қаралды 264,267

2 жыл бұрын

Subscribe to my channel for more weekly videos.
kzfaq.info...
Visit my store at weldmongerstore.com for TIG cup Kits, TIG Fingers, Gloves, DVDs, and other quality welding tools. New products being added weekly.
Welding open root practice plates is a good way to prepare for a 5g pipe test.
As long as thickness, bevel angle, root opening, and land are the same, the same settings and techniques that work on plate will work on pipe.
With pipe, you will still need to practice body positioning and transitions to different rod angles but other than that, the techniques used on practice plates will work on pipe.
hope this helps...
Follow me on social media to see what I’m up to:
Instagram: / weldmonger
Facebook: / weldingtipsandtricks
Join the discussion with thousands of welders at the Welding Tips & Tricks forum
forum.weldingtipsandtricks.com

Пікірлер: 130

@MikeP350 2 жыл бұрын

The best welding channel on the internet. Thank you for everything Jody. Goggins inspired me to go back to college, got my degree in welding with a 4.0 GPA, and this channel has helped me tremendously along the way.

@philthyphil3324 2 жыл бұрын

One of the most difficult things I've ever done was my 6g pipe welding test. I was brand new to welding, I spent hours and hours staying after work to practice. It felt so good when I passed. I put my heart and soul into the pipe fitter apprenticeship. Then one year in, the company shut down the apprenticeship.

@warrenjones744 2 жыл бұрын

Pipe welding is hard! especially when your 57 year old eyes don't focus as well as they used to and your not anywhere near as flexible as you were when you were 25 : ) I sure enjoy your videos Jody, especially the Tig welding. I suck at Tig welding, but thanks to your tutelage over the years I am much better at it. Cheers

@smiththers2 2 жыл бұрын

as someone whos been watching your videos for at least 6 years, and have learned a lot from them, im super happy to say that im starting a job in robotic mig welding next week! they will certify me in sheet metal by hand though as i go, so excited!

@jamesa7506 2 жыл бұрын

I can and do appreciate the time and effort in both the welding and production of the videos. A fine job and great accompanied tool for those learning this valuable skill. Thank you sir.

@tolhsge1795 2 жыл бұрын

Οολ

@ADJones-bn5mm Жыл бұрын

Great video, thank you.

@bogger_welder 2 жыл бұрын

Appreciate the time and effort on the videos 👍🏻

@MechanicTools1 2 жыл бұрын

Soldering technique is too good. thanks for sharing.

@PANTYEATR1 2 жыл бұрын

it's been a while since i got a notification from you Mr. Jody. glad to see you're still here kicking, screaming and teaching💪

@tntltl 2 жыл бұрын

Great to see Andrew again a phenomenal welder!!!

@garypostell5268 2 жыл бұрын

Excellent vid

@markashlock9017 2 жыл бұрын

Wow! Andrew has some serious skills! Also, GREAT Arc Shots!!! Thanks!

@amcj10 2 жыл бұрын

I used to think I could weld ok, but watching these guys I realize I don't know jack.....

@joedragaux8695 2 жыл бұрын

thanks for the video guys. good stuff.

@RC-Heli835 2 жыл бұрын

The greatest blessing in all my life was to buy my first box of 6010 rods for welding bore casing. I started out with 7014's because that's what my dad liked and they do make a nice pretty flat weld but very difficult if not impossible on any kind of vertical welding or overhead situation.

@jimkillen1065 2 жыл бұрын

I always enjoy watching these videos thanks

@bobroberson9286 Жыл бұрын

THIS VIDEO is a very good teaching tool and pipe is where the money is at for a welder !!!!

@klue507 2 жыл бұрын

Thanks for adding the video, I’m currently in a class for this and it is very well explained.

@ypaulbrown 2 жыл бұрын

some really great information and very clear picture and description .....thank you Jody and Andrew.....cheers from Orlando, Paul

@6pekXX 2 жыл бұрын

The guy from the video, this Andrew, he knows how to weld! Nice video! Thanks!

@patdexter9188 2 жыл бұрын

That 6010 might work on frames to for a root. This is crack repairs on heavy equipment, loaders, shovels. Then fill with 7018. Most of the time I fit a backer plate/ 1/8" strap then do the root with 3/32 7018 all uphill welds. This has worked well for me. The 6010 would save time for sure. I don't like using wire to much because its easy to over heat the work piece if your not watching the temp. Before temp guns I always did the spit test.

@Skhillz_FN 11 ай бұрын

It's been 8 years since I welded anything thanks y'all I know most of it I forgot my rod angle it's about 45 to 90 out front thx

@orbitalair2103 2 жыл бұрын

True professionals.....they make it look easy. Its a lot harder than that, lots of work and talent there in you 2 guys. Thanks for making these vids.

@MikeP350 2 жыл бұрын

Agree 100%. It looks easy until you do it yourself, takes a lot of work to be as consistent as these 2

@jac37 Жыл бұрын

Exactly. Positioning is everything in pipe. You don’t got that right rod angle you’re gon blow tf thru.

@Johnlu464 2 жыл бұрын

Love downhill on 6010 red rod. You can step in and out of the puddle and just stack dimes. 5p+ works great also just have love for some red rod. Being a union steamfitter I wish they would train more apprentices to master both up and downhill.

@jvazquez53 2 жыл бұрын

Beautiful welds!

@rolsonray 2 жыл бұрын

Hey Jodi, missed ya bubba...Im going to watch this just because I respect your experience , point of view, and just because your videos are always too shelf. Thanks Budd🇺🇸

@paulmorrey733 2 жыл бұрын

Thanks Jody and Andrew

@user-pe4sx7ey3m 2 жыл бұрын

First claas , very easy to follow, well done .

@ianjoseph145 2 жыл бұрын

Great video Jody thanks 👍👍👍

@adelramadan4622 2 жыл бұрын

Awesome work!

@garthbutton699 2 жыл бұрын

Another great video thanks for your efforts🤗😎🤗😎

@edfrancis7584 2 жыл бұрын

Just started college with pipe welding and this has really given me helpful information with how I should be running 6010 electrodes. Was having issues with the root and think the plate gap and how I was running the rod was the issue but watching this has given me a better understanding

@MikeP350 2 жыл бұрын

6010 roots take some practice before you really get the feel for it. Shove that rod in the gap and drag. Alot of people teach the whip and pause on roots. Alot of times it's not necessary IMO and it's easy to lose control of your heat and blow up the keyhole. My pipe instructor had 30 years pipe welding experience and taught me to do roots the same way Andrew is here. Was a game changer for me. Warm up the rod for a sec, shove it in that gap and drag the root in. Uphill or down.

@edfrancis7584 2 жыл бұрын

I was told and taught to pause and whip on the root and found exactley as your describing. Keyhole getting too big and loosing control. Going to just jam it in there and I'll let you know after my next evening course 😂

@MikeP350 2 жыл бұрын

@@edfrancis7584 It works great for me. I didnt know you could drag a 6010 like that until my instructor showed me. This is the first 6010 youtube vid I've seen showing this technique as well. The key is keeping pressure on the rod and the proper travel speed. Having the arc jammed in there chokes the voltage and keeps the heat down. I don't understand why more people don't teach this method. Good luck to ya, let me know how it works out for you.

@rainsrapidly 2 жыл бұрын

Lmao I just shove it in ... crackle crackle push push push... moveeee 😅😅😅

@rainsrapidly 2 жыл бұрын

Another tip... a closer closed gap will help u with keyhole control... some guys i work with barely like any gap

@rezboy327 Жыл бұрын

Thank you👊🏽

@rainsrapidly 2 жыл бұрын

Beautiful welding

@kojomensah7474 2 жыл бұрын

Thanks

@adamstripp39 2 жыл бұрын

Great video

@user-et4tl7gx2j 2 жыл бұрын

Блин у нас в России такого нет, все засекречено, да и видео уроков таких тоже мало, как хорошо смотреть такое интересное видео..

@saidfahmi9805 Жыл бұрын

Good job 👍👍👍👍

@giannirocco7492 2 жыл бұрын

Desire,dedication,determination!I call this The Three "Ds"of Success!If anyone has and keeps The Three "Ds" they will absolutely succeed!This was my personal method,this is how I got to the top of my game as a union welder!(Plumbers and Pipefitters,local 725)

@RPMechanics 2 жыл бұрын

Very good info and video.

@JuanTorres-uo3ol 2 жыл бұрын

Muchas muchas pero muchas gracias por compartir su conocimiento, estoy iniciándo en la cañería y sus vídeos me han proporcionado lo necesario para encontrar la técnica!! Aunque no entiendo mucho de inglés, con verlo más lo poco q me han enseñado e mejorado!!!! Muchas muchas Gracias!!! Abrazos a la distancia!!!!

@jadegouge8239 2 жыл бұрын

Good stuff

@KASTIANYCH_ 2 жыл бұрын

Очень Хорошо! Спасибо)

@Elkmonger Жыл бұрын

I work a lot in refined petroleum product pipeline in the northeast. I haven't seen HYP on a weld procedure in 15 years. Also, most of the welding procedures detail same diameter rod for root AND hot pass. I mainly work on 16" and under. The only time I see 3/16 is maybe in a fill pass or cap. Guys also try and manage your fill so you end up flush or maybe just a hair low on the last pass before the cap. Keep this fill the same all around. No short striping. The inspectors are gonna be watching for that. Take care.

@arturocruz1993 2 жыл бұрын

Hey Joey, thank you for the amazing content. Besides pipe, when is 6010 good for? Can you make a video of when to use a certain rod. 7018,8018, 6010, etc etc

@mr.hridoyahmed4131 2 жыл бұрын

Nice🥰🥰

@beardedgaming3741 2 жыл бұрын

I'm just learning how to weld, have 110 volt wire feed. It amazes me how fast he can go on this and still get penetration into that thick pipe

@vjjhbbhhbbb8433 2 жыл бұрын

good

@charleschilders3216 2 жыл бұрын

5p bead, 70+ out. We use 8010 pipeliners. Fewer companies allow hyp anymore.

@mikemmcmeans 2 жыл бұрын

3:06 you can see the flux action covering up 'the light'

@HauntedBranch 8 ай бұрын

Hey Jody what would you suggest for welding 4 in od pipe it's close to 1/4 in thick wall. I have 6011 3/32 and 1/8 - and 7018 1/8 rods . I can order 6010 rods if it would work better . Would this be a one pass weld ? what would recommend.

@antemarov3836 2 жыл бұрын

Celuloza elektroda for pipe

@mohamadyasertamr4658 2 жыл бұрын

رائع جدا أتمنى أن يكون ترجمة باللغة العربية وشكرا لكم

@br6768 2 жыл бұрын

Man that's a really hot soldering iron

@TheSRBgamer63 2 жыл бұрын

Hello everyone.I need to weld chassis of mine wheel loader ,it's cracked at one side and i was wondering what would be best way to do it ,which types of electrodes should i use ?.I don't really know what type of steel is on loader chassis,i've seen on internet many types of electrodes used for this type of fix. 6010 as root pass then fill with 7018 ,or even some stainless steel electrodes such as e 307-17 or e312-17.

@chorgzent.3978 2 жыл бұрын

Cah-den gotta add the sticker to the pancake hood! We all answer to one risen Lord no cap 🙏

@matthewantolino5658 2 жыл бұрын

In the video you talk about 7010 hyp rod, which is designed for vertical downhill(according to the Lincoln information), but the video description says 6010. Can you clarify which is correct for the video? Based on what I have seen of the video, it welds like 6010... but I have never seen 7010 run... either way I never realized that 7010 electrodes existed until I saw this video. Just wondering if I discovered a rod that would work for Field repairs outside of pipe.. Might be a new tool for the mental toolbox... or on the work truck Thinking about plans that call for 70XX Electrode... not needing a rod oven by using cellulose coated electrodes instead, could be beneficial in some scenarios.

@weldingtipsandtricks 2 жыл бұрын

First 2 Plates were done with 1/8 6010 Pipe and third plate 7010. Techniques are pretty much the same

@matthewantolino5658 2 жыл бұрын

@@weldingtipsandtricks awesome. Thank you... going to have to grab some to run it... can't get better if I keep doing the same thing.

@chappieworkz3288 8 ай бұрын

Awesome 👌👌👌 Welder here

@kennetht66 2 жыл бұрын

Do you change polarity on root ? Thanks

@victoryfirst2878 Жыл бұрын

What is the reason for using 60s and 70s rod changes ???

@ozdig2163 2 жыл бұрын

Очень поучительно, ждем следующих видео. Вот бы увидеть обзор маски вашего напарника.

@demethrey 2 жыл бұрын

The hood is a basic pancake hood made for pipe welding definitely my favorite hood for all welding processes

@olddawgdreaming5715 2 жыл бұрын

Thanks for sharing with us Jody, good information. Fred .🙏🏻🙏🏻👍🏻👍🏻👏🏻👏🏻✋🏻✋🏻

@christopelsihombing7875 2 жыл бұрын

Mana diberlakukan welding turun buat tes.. Heang... 😁 Sai naeng dibahen do ..

@JesseWright68 2 жыл бұрын

Thanks for another great video, Jody! For everyday, non-coded work, is there a difference between 6010 and 6011 rods other than 6010's must be run on DC?

@weldingtipsandtricks 2 жыл бұрын

Not much IMO

@chancesanborn7932 2 жыл бұрын

The slag is a little heavier. Other than that they run pretty similar.

@logangray3464 2 жыл бұрын

@jesse Wright: I have seen 6010 ran on AC current and it ran the same as DC current. Some DC welders won't even run a 6010 electrode.

@weldingtipsandtricks 2 жыл бұрын

@@logangray3464 inverters have changed the game. Even 7018 open roots can be run on AC with certain settings

@waynegroves6922 2 жыл бұрын

@@weldingtipsandtricks I've been hobby welding for over forty years, building street rods and motorcycles, mainly; however, a lot of my welding jobs involved heavy plate, for which I used a lot of 6010/11 - on an old 200a AC buzzbox. I've also ran 7018-ac rods on that same box, with beautiful, shiny, and flat beads. Up until one particular job, I didn't realize there were 7018 AC rods on the market.

@MistaE 2 жыл бұрын

Can 6010 and 6011 be ran straight or do those rods have to be manipulated?

@weldingtipsandtricks 2 жыл бұрын

I have seen roots welded with no manipulation but all else seems to like a little motion

@RrrRrr-yc5lk Жыл бұрын

Hi iam a welder Sui nothern Gas company

@Jamestreeman 2 жыл бұрын

How can I get ahold of you?

@manimeraj2634 2 жыл бұрын

Aap Kahan say hi aap log kahan kam Karte Hain aap log ke pass Ham Kaise Aaye please bataiye na mera name rembo Salman

@giottolaudo7672 2 жыл бұрын

The techniques etc are all the same with 6011 right? (My machine doesn't like 6010) I know they're supposed to be essentially identical but I wanted to make sure.

@giottolaudo7672 2 жыл бұрын

@@luckyPiston I meant the techniques for downhill and uphill pipe, passes, etc, sorry I wasn't clear. Yeah, my inverter welder is DC only, but it doesn't like 6010... at all.

@NickFrom1228 2 жыл бұрын

@@giottolaudo7672 Yea, most DC inverters don't have the voltage to keep 6010 lit. Bummer. If I recall some are now coming out that will do 6010 but I haven't tried any. With 6011 I like AC because the bacon frying sound is so distinct you can almost use it as an indicator of how well things are going.

@6pekXX 2 жыл бұрын

@@giottolaudo7672 The machine must have a good and massive drosel/choke coil and a good reserve of voltage!

@safaatchannel4538 2 жыл бұрын

👍👍👍

@ickabod545 2 жыл бұрын

Where can I get a welding hood like that?

@JesseWright68 2 жыл бұрын

Do a search for pancake hood or helmet.

@treverwhoever6733 2 жыл бұрын

Running 309 downhill.. little different than 60.

@Den-uw3rs 2 жыл бұрын

Так и не могу въехать, чем эта чудо-юдо маска удобнее обычной

@edwardclark3980 2 жыл бұрын

With 5p+

@robmurphy806 2 жыл бұрын

Is this a reupload..? Could of sworn I've seen this all before...

@edwardclark3980 2 жыл бұрын

5p or 5p+ ?

@6pekXX 2 жыл бұрын

Isn't 5p actually +++++ / like 5 pluses?

@Then.72 9 ай бұрын

Not allowed in certain nations as vertical up is only allowed

@kevinreardon2558 2 жыл бұрын

Still, thanks for not dumbing it down.

@erush611 2 жыл бұрын

Welding downhill doesn't result in porosity?

@MikeP350 2 жыл бұрын

No, it is very common to run 6010 downhill for roots and hot pass, 7018 is always uphill though.

@erush611 2 жыл бұрын

@@MikeP350 I was on a welding project in merced and the guy welding downhill was caught by the inspector welding downhill. The inspector made him grind it all out and as he was grinding you could see the pinholes all throughout

@MikeP350 2 жыл бұрын

@@erush611 with 6010?

@user-ju3cg3lh9n 2 жыл бұрын

🛠🛠🛠👍

@Killnet.111 2 жыл бұрын

Приветствую колега. Покажи пожалуйста, как ты веришь в неудобном положение, ведь в практике случается, так что в большинстве случаев приходится варить в неудобном положение, покажи, как надо правильно варить. Взарание спасибо.

@mdjamantalukdar7774 2 жыл бұрын

Me welder

@WildWestGarage 2 жыл бұрын

I always thought welding down hill would cause slag inclusion, what’s the trick here?

@rich3633 2 жыл бұрын

They're cellulose rods mate, so the slag freezes very quickly, they are designed for this sort of application. You wouldn't necessarily be able to do this with basic or rutile rods, although some are designed to be used for downhill. The manufacturer's literature will advise on what rod is suitable for the application you require 👍

@WildWestGarage 2 жыл бұрын

@@rich3633 Thanks, I figured it had something to do with the chemistry of the rod, I know down hand with 7018 is a no no.

@rich3633 2 жыл бұрын

@@WildWestGarage no probs dude, they do actually make a hydrogen controlled rod for downhill welding, I've never used it mind. I don't want to sound like a d**ckhead but downhand is actually the flat position ( for some reason?!). Downhill or vertical down is the way it's normally phrased, anyway, all the best pal. Cheers for the reply👍

@WildWestGarage 2 жыл бұрын

@@rich3633 Schooled, thanks.

@rich3633 2 жыл бұрын

@@WildWestGarage I only know because someone told me once upon a time mate. Same as everyone else 👍

@mdjamantalukdar7774 2 жыл бұрын

My helip