ACPWorkbench Audio Effect Tool Step by Step Tutorial
Рет қаралды 14,483
Күн бұрынACPWorkbench Audio Effect Tool is a software that can help you customize different audio effect and system configuration to your Arylic units. Like L/R balance, Separate EQ control for each channels, pins configuration and more.
Current compatible devices are:
Up2stream Series(except Up2stream Amp Sub), S10, SA100
*ACPWorkbench is a Windows Software
*Each activation license key can only be used once in a single computer
*Remember to use a Micro USB cable that can transfer data from PC to Arylic units
ACPWorkbench Audio Effect Tool ▶bit.ly/3pTI9LS
--------------------
0:57 ACPWorkbench Installation
3:13 Connect to PC by Micro USB
4:31 ACPWorkbench Demonstration
5:28 Main EQ Adjustment
7:35 Different Audio Effect Demo
9:32 Left ,Right and Mono Channel separate EQ adjustment
11:30 Change Pin Configuration
12:58 Save your Configuration to the Device
13:30 Firmware Upgrader
13:56 Export your Audio Settings
14:58 Reset the Settings
--------------------
💡Learn more about Arylic: www.arylic.com/blogs/news
💡Know more about our system: www.arylic.com/pages/how-it-w...
💡Find our products here: www.arylic.com/
Subscribe us ▶bit.ly/3jE3GFV
📢Follow us
▶Website: www.arylic.com/
▶Instagram: / arylic_audio
▶Arylic Facebook Page: / arylicme
#Arylic#Up2stream#ACPWorkbench#DIYaudio#wirelessamplifer#Tutorial#homestereo#wireless#EQ
@donaukanal942 Жыл бұрын
Hello! Is there a way to connect the upstream board wireless to the pc
@zarster 3 ай бұрын
Very good video! Will for sure get the software. Need to figure put how to use the GPIO to CTRL put when input is detected
@KolfMAKER Жыл бұрын
Great video! I want to use the ACPworkbench with the Up2Stream Mini. For my case I need to limit the output volume (for instance to 60%). Should I make these settings on: (a) ‘Audio Module’ tab, under ‘Volume control’ (which slider in this section)? (b) ‘Audio effect’ tab, under ‘Main EQ’ and then ‘Pre-Gain’?
@Arylic Жыл бұрын
Option b😁😁
@cBoTy6e 3 жыл бұрын
Arylic S10. Treble and Bass are incorrectly adjusted after the last update (4.2.9326.24)!!! How to return to the previous firmware ??? Everything worked correctly on it.
@trei2unu 2 жыл бұрын
In the custom EQ section, is it possible to also set the Q, Gain and Fc by clicking on the values? Also, any plans on making a 4 channel amp so it can be used as an active crossover between the tweeter and woofer as well?
@zach4384 9 ай бұрын
You can use two Up2stream mini boards and connect them together in the app.
@deltastories6859 Жыл бұрын
Great product, chaps. However. delay / time alignment for each channel is a vital feature currently missing. I hope it is coming soon . . . Also, in the video, the only panel you do not click is the most important one: showing extended options for PEQ on each channel - I have seen that in this section there is the possibility to set cut-off frequency, and I was hoping for individual channel delays, too. As others have said, a four- and six-channel version would be great.
@Arylic Жыл бұрын
Thanks for the detailed feedback. Will manage and report to our team😁 As for the delay adjusting you can try the tools here: forum.arylic.com/t/add-airplay-to-your-android-phone/180 BTW Black Friday SALE may coming soon! You can refer to this link for more info: www.arylic.com/pages/activity
@vladi_ed 11 ай бұрын
@@Arylic the author was talking about delay for each channel (left, right, subwoofer).
@pmsrodrigues 14 күн бұрын
I actually think this is a great tool, but it is missing a trick: using a microphone to create an EQ curve to help correct for speaker and room inaccuracies. Even if imperfect, it would go a long way to improve things.
@Arylic 13 күн бұрын
Hi Sir, thanks for your very great idea! Currenty our devices is not well to support mic, but we already in progress to plan some products with mic features:)
@pmsrodrigues 13 күн бұрын
@@Arylic I meant to use the microphone of the computer running ACPWorkbench, or preferably cheaper external mic, and placing it in the listening position. Shoot some test tones which you capture and analyze. Generate EQ curve. Profit.
@dannyaustin84 Жыл бұрын
Hi. My version (just purchased) of APC Workbench doesn't have the options to allow me to adjust EQ for L + R separately. I need this function to act as a crossover. Do I need to update the firmware on my board? Any idea of how I can get hold of the bin files?
@Arylic 3 ай бұрын
Hi Sir, you can send your firmware version and the screenshot of ACPworkbench to our customer service mail: info@arylic.com. Or if you can send the video that would be great. BTW, what is your product model, some models can download GO CONTROL APP for L/R balance.
@janschmitz2583 2 жыл бұрын
Is there a way for time alignment between left, right Channel and sub? ( Using the 2.1 AMP)
@Arylic 2 жыл бұрын
Hi Jan, thanks for your nice feedback. We don't have this currently, but we plan to do this in future update. Thanks
@RatsM7 4 ай бұрын
@Arylic Did you?
@yurianhuizing2352 2 жыл бұрын
Hi, the Up2stream pro v3, How can i get a output pin to give 3 volt when playing audio? And turn off when there is no audio
@Arylic 2 жыл бұрын
Hi Yurian, your questions are related to tech issues. Could you send a mail to info@arylic.com? We will transfer to our tech team to help you.
@cmdesteves 2 жыл бұрын
I bought the software, I have a S10 preamp and UP2STREAM V1.0 and I can't get the software to work, I've tried several data cables, but to no avail. It always gives USB disconnected
@Arylic 2 жыл бұрын
Hi Carlos, I advice you send a mail to our customer service. They will help you figure out the issue. Some products that release on 2018 or 2019 is not supported this feature.
@hyrule2486 2 жыл бұрын
Hey how can i use de digital out?I connected to my onkyo but there s no sound??Thanks.
@Arylic 2 жыл бұрын
Hi Filme, please contact our support team: info@arylic.com
@andreimelinte1136 3 ай бұрын
Hello, how do you proceed if the program will not save the settings? After restart of the device the settings are gone. I've tried to use index 0 to 6, also i did some logs and i saw that cominication is done but there is no writing on the chip itself for using downloader and then save configuration to flash
@SamuraiGuy 8 күн бұрын
I'm having the same problem. Did you find a solution?
@stanislavtodorov8705 Жыл бұрын
According to the provided manuals for up2stream Mini/Pro v.3 , the boards are running in MASTER mode. If I want to output the I2C signal from the Mini/Pro boards to another device (in my case ADAU1701 dsp), the connected device should be in slave mode. Is it possible to set the Mini/Pro to work in SLAVE mode with this software? May be frin the MODE dropdown menu in the I2S0 tab. And then from SETTINGS -> MCKL SOURCE (GLOBAL) to select MCLK IN0 instead of PLL Clock1? If this works, I will be probably able to set the ADAU1701 as a master and output it's MCLK signal (12.288MHz) to the Mini/Pro, which would be much more convenient for me. This is the only thing which stops me from ordering an up2stream Mini 3 module. Best regards!
@Arylic Жыл бұрын
Hi Stanislav, this is not available.
@ford1546 7 ай бұрын
It doesn't have the usual 10. 15. 30. band eq mode??? does it cost anything to use the software.
@ashyouknow7420 2 ай бұрын
Yeah it costs 20 bucks
@ivosimba496 3 ай бұрын
How use they firmware update. How to. Create el. File.mva please help me
@boppos 3 жыл бұрын
Did I understand correctly: when I buy a new computer or reinstall windows I need to rebuy acp workbench?
@Arylic 3 жыл бұрын
The key is memorized by the harddrive, so if hardrive clear the data the registration history will disapeared
@hyrule2486 3 жыл бұрын
@@Arylic And if i clone the drive?
@Arylic 3 жыл бұрын
@@hyrule2486 The license is locked in the driver, so if the driver memory or record will be erased, then you need a new license key.
@09ThunderOne Жыл бұрын
If I save a custom EQ, will that custom EQ be in the phone app afterwards? Thanks
@Arylic Жыл бұрын
It won't sync to the app. But the number is correspond to the numbers of remote preset content.
@danielpeterson5404 5 ай бұрын
how to delay channels 1 2 and subwoofer
@Andreas123211 2 жыл бұрын
When I try to save the configurations to flash, NOT all the configurations are saved. However, I only try to save two audio effects, and it can only save the "Harmonic Exciter" configurations but NOT the "Virtual Bass" configurations. The "Save Configurations to Flash..." pop-up is also pretty confusing, but I use the default settings when I save. I have the "Up2Stream mini V3". Please help. =) Otherwise, I love the module.
@Arylic 2 жыл бұрын
Hi Andreas, this is a known issue for saving the virtual bass. Will fix in future update
@Andreas123211 2 жыл бұрын
Okay, thanks. Do you know the time frame for when the update is available via the 4stream app? :)
@Arylic 2 жыл бұрын
Estimated on March
@Andreas123211 2 жыл бұрын
@@Arylic Hey, the firmware update you said was estimated March has still not been released as it seems? I have the Arylic mini V3, but does that even supprt the new update 4.6.415145?
@lancebyphone3136 8 ай бұрын
Please How to adjust name of MV silicon
@IainMacUK 3 ай бұрын
Please update your info. I believe this Windows software is compatible with your BP50. Can it do base management on the sub output??? Thank you.
@Arylic 3 ай бұрын
Yes, BP50 is supported, you can adjust the sub channel frequency.
@IainMacUK 3 ай бұрын
@@Arylic That's good news. Thank you. Can you band pass the fronts? So low bass to the sub and everything else to the fronts? Full bass management...
@soyusunk 3 ай бұрын
How to setting bluetooth delay for Up2stream mini board
@Arylic 3 ай бұрын
You can achieve the goad by 3rd party app, check this: forum.arylic.com/t/add-airplay-to-your-android-phone/180/9
@soyusunk 3 ай бұрын
@@Arylic Can not setting in ACPWorkbench ?
@Brecher87 2 жыл бұрын
What must I do, to activate the volume encoder board? I plugged it to my Up2stream Mini V3 but it doesn't react. 😕
@Arylic 2 жыл бұрын
Hi Falko, I advice you can send your wiring and the screenshot of your ACPWorkbench too to our forum, we will check and let your know.
@Brecher87 2 жыл бұрын
@@Arylic I already asked in the support forum. Everything is connected properly and the ACP settings were corrected (reset to standard). Now I can only turn up the volume. Turning volume down activates the bluetooth source (wtf?!). Pushing the volume knob does nothing. I hope some one will help me. :-(
@Arylic 2 жыл бұрын
@@Brecher87 I recommend you can feedback your problems in forum post continuously. Our pro engineer will give you the best suggestion there to help you.
@SamuraiGuy 8 күн бұрын
Is there a way to make my B50 remember my EQ settings after it turns off or goes into standby? I don't want to apply the settings every time I want to listen to music. I don't even want to have my computer connected to it at all. Surely there's a way to save to the device, right? I can hear it changing when I mess with the app, so I know it's affecting it. It just resets every time it goes to sleep or turns off.
@Arylic Күн бұрын
Hi, you can save that following EQ>Custom EQ>select the drop down list> Add custom>Save.
@SamuraiGuy Күн бұрын
@@Arylic that's how I did it from the app, but that's only a graphic EQ. Is there a way to save the PEQ settings from the ACP Workbench app to the device?
@Arylic 7 сағат бұрын
@@SamuraiGuy Yes, please see 12:58
@SamuraiGuy 3 сағат бұрын
@@ArylicI completely missed that part. Thank you so much!
@Brecher87 2 жыл бұрын
Can you please make a video on how to activate the "SPDIF IN" module?
@Arylic 2 жыл бұрын
Actually you can find the answer in 11:30, change the spdif part to spdif in.
@Brecher87 2 жыл бұрын
@@Arylic I already knew that. The problem was, that the Toslink-input not worked properly (sound distortions). Solution is: DO NOT USE THE CABLE THAT IS SHIPPED WITH THE SPDIF IN MODULE. You can only connect 3 pins from the SPDIF module to the Up2stream mini -> "SPDIF", "GND" and "VCC_3V3". The other 4 pins are useless for the SPDIF IN and will cause electro magnetic interference (distortet SPDIF signal) if connected to the Up2stream. ;-)
@nordioale 2 жыл бұрын
hello, but with the arylic mini v3 i can use also this software for set the filter? best regards
@Arylic 2 жыл бұрын
Yes Up2stream Mini V3 is available.
@alexdj1742 Жыл бұрын
can I convert the input line signal to “phono” line? (turntable) greetings 😅
@Arylic Жыл бұрын
Sorry this is hardware related which is not available😂
@martifabregabueno9986 3 жыл бұрын
Can be installed on an external drive?
@Arylic 3 жыл бұрын
Sure, just make sure to run on Windows system.
@martifabregabueno9986 3 жыл бұрын
@@Arylic So it could work on 2 different computers? Or will only work on the first one where it was used? I currently have one AMP but I am planning to get a second one in a completely different location and I want to be sure if I can use the program for both of them without needing a laptop or moving the AMPs from one location to another. Thanks
@nthy_0684 2 жыл бұрын
hi friend have delay for each chanel /???
@Arylic 2 жыл бұрын
about 20ms, it is hard to hear that if you are listening music
@HalRockwell Жыл бұрын
So, if I buy a new PC, I must buy the software again?
@Arylic Жыл бұрын
You can send a mail to our customer service: info@arylic.com. Once we confirm your order we will send you a new key.
@haha12678 3 жыл бұрын
nice video! but can you also explain the audio module page
@Arylic 3 жыл бұрын
We recommend do not change the settings on that page.
@arielfernando3916 3 жыл бұрын
I realize I am kinda randomly asking but do anybody know a good site to watch new series online?
@shilohjuelz2478 3 жыл бұрын
@Ariel Fernando i use FlixZone. You can find it by googling :)
@soyusunk 3 ай бұрын
How to change soundsystem to other name for device ?
@Arylic 3 ай бұрын
It is pretty simple! open 4stream APP>click device settings>rename and you are done!
@soyusunk 3 ай бұрын
@@Arylic I user bluetooth with a car only
@Arylic 3 ай бұрын
@@soyusunk Which model do you have? For WiFi model you need to use WiFi to change the name. You can try use a phone as a hotspot.
@phantuanphong7465 3 ай бұрын
decryption key please! how to have!?
@ashyouknow7420 2 ай бұрын
Buy from their website
@lancebyphone3136 8 ай бұрын
Please how to adjust name of bluetooth
@Arylic 8 ай бұрын
It is easy. For WiFi line products, open 4stream APP>device settings>Rename For Bluetooth line products, open GO CONTROL APP>settings>Device Name.
@thesheldonroth 2 жыл бұрын
4stream seems much worse. Can no longer control all of synchronized speakers volume at once... Only one speaker at a time
@Arylic 2 жыл бұрын
Hi Sheldon, you need to update all units to the newest firmware then the issue will solved.
@dannyaustin84 Жыл бұрын
@@Arylic Where can I get updated firmware bin files from?
@caioferrari 2 жыл бұрын
You sell a software for someone that bought your product? This is dumb
@Arylic 2 жыл бұрын
Hi Caio, sorry for your bad experience. But we for this software we have lifetime maintenance and update, so we need to spend time and cost on it. Hope you can understand.
@caioferrari 2 жыл бұрын
@@Arylic it’s hard to understand. I bought an A50+ and it doesn’t sound good. Compared to my old AB amp it sounds sharp, too much highs. terrible. Would be essencial to equalize it and try to improve its sound but…. I have to pay extra for it
@Arylic 2 жыл бұрын
@@caioferrari Our amplifier is class D amplifier. For the sound issue you can write a mail to info@arylic.com. We will help you check if there is an issue or not. If yes, we could send a replacement and refund to you. Thanks
@ftt-prod 15 күн бұрын
@@caioferrari You can find it for free ;) Some links when it was free are still alive :) And no key needed
WONDOM Audio
Рет қаралды 4,2 М.
Immersed
Рет қаралды 89 МЛН
TheDIYGuy999
Рет қаралды 5 М.
Chris Selim - Mixdown Online
Рет қаралды 19 М.
Buy Smart┃Магазин ноутбуков
Рет қаралды 1,6 МЛН