How to make a DIY Bottle Opener with Magnetic Cap Catcher that sticks to your fridge!
I made a version of this for my Brother in-law and used the same concept to make one for my Dad for a Christmas gift. The stepes are quite simple and you don't need too many supplies or tools.
HOW TO:
1) Cut some wood to length/width. I used some pine 140mm x 300mm (5.512 inches x 11.81 inches)
2) Draw your design with pencil/pen on the wood
3) Route out the design
4) Seal wood with a small amount of epoxy resin
5) Go around the design with a hot glue gun to create a damn for the resin
6) Mix mica powder or resign dye with your clear epoxy resin
7) Pour into the design
8) Once dry remove the hot glue and sand
9) Start with 40'grit and then work up to 320'grit (40,80,120,240,320)
10) Turn over the design and drill with a Forstner bit the same thickness as the magnet to stick to the fridge and then a deeper hole for the cap catcher magnet (You may want to use 2 magnets to catch the cap). Ensure you don't drill too deep and break the surface of the wood or epoxy.
11) Attach the cork by cutting it to size and sticking it down
12) Seal the wood with a Oil/wax of your choosing
13) Attach the bottle opener
14) Get a cold beer from the fridge and test it out and drink your reward for a job well done 🍺😃
FREE GUIDE: If you are considering taking up resin art as a hobby, or even a side hustle then grab my FREE guide on Resin Basics for Beginners on my website
upbeat-artist-9488.ck.page/be...
-------------------------------------------------------------------------------------------------------------------------
🖌🎨 ART SUPPLIES 🖌🎨
Resin: amzn.to/46ApieL
Resin Molds: amzn.to/3OhoT8z
Resin Dye: amzn.to/3DGvjcC
Measuring Cups amzn.to/43RbLgb
Alcohol inks amzn.to/3DGvjcC
Mica Powder amzn.to/3YpNVHd
Glitter amzn.to/3YpNVHd
Foil amzn.to/3Qnmxrn
Natural materials amzn.to/43Rghew
Pressed flowers etc amzn.to/43Rghew
Acrylic Supplies: amzn.to/3XyHUYi
Silicon for Molds: amzn.to/3PFNKFn
Vacuum Pot only: amzn.to/44eTTgo
Vacuum Pot and Pump: amzn.to/3pqr5SX
Pressure Pot: amzn.to/3JGgU3f
SAFETY EQUIPMENT:
3M Half Mask amzn.to/44X7n0w
3M Organic Vapour Filter amzn.to/45kEBH1
3M Eye Protection Goggles amzn.to/3OnMbJR
Nitrile Gloves amzn.to/3s4QkLy
-------------------------------------------------------------------------------------------------------------------------
✨🎇 FOLLOW ME ✨🎇
Tik Tok: / andysartlab
Twitter: / andysartlab
Instagram: / andysartlab
Web and Blog: andysartlab.com
Newsletter: zaap.bio/andysartlab
-------------------------------------------------------------------------------------------------------------------------
🔧🔨SOFTWARE I USE 🔧🔨
Link in Bio: 10% Off code 'zaap10' zaap.ai/?ref=andysartlab
Boarderless Banking: Wise wise.com/invite/ath/andys99
Social Media Content Re-purposing: neon.ly/repurpose
Email Marketing: neon.ly/aweber
VPN: SurfShark: neon.ly/surfsharkoffer
KZfaq Optimization: www.tubebuddy.com/nftiethings
--------------------------------------------------------------------------------------------------------------------------
DISCLAIMER
These videos are for entertainment purposes only. Follow manufacturer instructions and always wear PPE when dealing with chemicals like resin. Some of the above links contain affiliate products where we make a small commission, but at no additional cost to you.