Amiga 600 RGBtoHDMI Installation

Рет қаралды 28,142

Күн бұрын

I'm installing a very elegant solution for the RGBtoHDMI mod into my Amiga 600. // Kindly sponsored by PCBWay - Get your first PCBs free! - www.pcbway.com/
The follow up video is here: • Amiga 600 AmigaOS 3.2 ...
Joachim's GitHub with the Gerber files for this mod: github.com/jockel71/RGB_HDMI_...
General RGBtoHDMI project page from hoglet67: github.com/hoglet67/RGBtoHDMI...
Amiga RGBtoHDMI page from c0pperdragon: github.com/c0pperdragon/Amiga...
A1K Forums: www.a1k.org/forum/index.php
My previous videos about Amiga and RGBtoHDMI:
Amiga 500 Installation: • Amiga HDMI with a Rasp...
Amiga 500 Updates: • Amiga RGBtoHDMI (with ...
Amiga 2000 (ECS) Installation: • Amiga 2000 RGBtoHDMI I...
Buy a Raspberry Pi Zero (affiliate links)*:
US: amzn.to/2Lr9bLr
UK: amzn.to/38fSz21
DE: amzn.to/3op3HPO
Mini HDMI plug with Flat Flex connector (DE): www.berrybase.de/audio-video/...
Regular size HDMI socket with Flat Flex connector (DE): www.berrybase.de/audio-video/...
20cm Flat Flex for HDMI connection (DE): www.berrybase.de/audio-video/...
TIME STAMPS:
0:00 Introduction
1:27 A600 with a regular Upscaler
2:56 HDMI port installation
12:09 RGBtoHDMI Hardware Installation
13:14 Sponsor Message
13:56 Installing the Adapter Board
17:17 Software Installation
18:49 Test Run
21:19 Jan Beta was here!
22:33 Does the case still close?
24:11 Thank you & Good night
--------------------------------------------
MUSIC by FOCUS 10 focus10music.bandcamp.com
EQUIPMENT AND TOOLS I USE: kit.co/janbeta *
TWITTER: / thejanbeta
PATREON: / janbeta
WEBSITE: www.janbeta.net
TWITCH: / thejanbeta
YT CHANNEL MEMBERSHIP: / @janbeta
Thanks for watching!
This video was sponsored by PCBWay.
* Stuff marked with "*" contains affiliate links. You don't pay anything extra and I get a little commission from everything you buy through the links (even if you buy something different there).
#JanBeta #Amiga #Commodore #PCBWay

Пікірлер: 240

@RetroRecipes 3 жыл бұрын

You weren’t kidding when you said it was an elegant solution. So satisfying how the HDMI socket fits in the case hole there. Nice work everyone involved! 👍🕹️

@JanBeta 3 жыл бұрын

Thanks! Yes, beautiful work indeed. And really handy to have HDMI in this small footprint Amiga. :)

@Dkentflyer 3 жыл бұрын

A very neat little interface, it's amazing seeing what people come up with. Great video as always Jan, look forward to seeing the follow up.

@stupossibleify 3 жыл бұрын

I've been waiting for a A600 version. Thanks for the video, Jan

@RayBrooks0 3 жыл бұрын

Jan this is AMAZING. Thanks so much to Joachim and you for demoing. This is my next Amiga project.

@JanBeta 3 жыл бұрын

Thanks! Hope it works well for you. :)

@einziger33 3 жыл бұрын

Wonderful solution to get HDMI for the A600, great work!

@parrottm76262 3 жыл бұрын

So very glad someone like Jan allows us to see all the wonderful upgrades done in place. Upgrades my hands no longer let me do on my own. Gives me great pleasure watching these.

@JanBeta 3 жыл бұрын

Thanks! Sorry to hear you are not able to do these mods yourself anymore. Glad you at least get some pleasure from watching the videos! :)

@nerdygeezer78 3 жыл бұрын

Always good watching you mod a Amiga 👍

@jondough76 3 жыл бұрын

No need to feel bad for breaking that flat flex connector. Those things can be a pain in the ass even under ideal conditions. Keep up the great work!

@MichaelOglesby 3 жыл бұрын

Fantastic video! Seriously thinking of doing this!

@PaulinesPastimes 3 жыл бұрын

I little tiny let down at the end, but I'm sure there will be a follow up video 😁. A fun video. Beautiful image quality and fantastic upgrade. 😊👍

@VincentGroenewold 3 жыл бұрын

Jaaaaay, I was getting bored, thanks Jan! :)

@Plan-C 3 жыл бұрын

Looks great. Nice vid. Thanks.

@JARVIS1187 11 ай бұрын

I think this will be my solution for my newly bought A600 which will arrive in a few days. This looks awesome and no one will even know what happened inside :D

@_commodore_ 2 жыл бұрын

Thanks for good videos, I am on your patreon list now 🤜🤛

@chrisrichardson1600 3 жыл бұрын

Great video! Will be doing this to my 600, just need something similar for my 1200 now..

@JanBeta 3 жыл бұрын

Thanks! Unfortunately the Pi is not powerful enough for the AGA screen modes. And as far as I know the signals are processed differently so there would have to be a whole different method in order for this to work. Maybe someday.

@philipkoekemoer4705 3 жыл бұрын

@@JanBeta indivision aga mk3? Did a similar mod with it and the rf port..

@antonioarezzo4549 3 жыл бұрын

Thank you very much for everything you do.

@jobniekel5555 3 жыл бұрын

Jan, thanks for the detailed video you've uploaded. Great to see this solution working for the 600. I've had a look to do this myself, but I can not find the adapter board for the A600 mentioned. (the one with the cable and Denise adapter) Is there any way to aquire it preready made, as shown? Many thanks, Job

@imalebowski 3 жыл бұрын

Thanks for shooting this with all the screw-ups in. Makes me feel better about my own shoddy work ;) How is Interlace modes?

@JanBeta 3 жыл бұрын

Thanks! I always leave my mistakes in the videos so people don’t have to repeat them… :D interlace modes work beautifully and flicker free. Only for the OCS modes though, super hi res and the other ECS stuff looks a bit messy and is missing some pixels.

@JohnSweevo 2 жыл бұрын

To err is human, to really screw up get Jan ^^

@slowlymakingsmoke 3 жыл бұрын

That is what I am keeping my empty RF port for on my A1200. I just need those wonderful engineers to work out how to do this for the AGA machines.

@philipkoekemoer4705 3 жыл бұрын

Indivision AGA mk3 , just did a similar mod with this card and the rf port

@ExGemini 3 жыл бұрын

In failure we learn :) And Turrican 2 ... how I cannot love videos like this! :)

@grzegorzbilski2315 5 ай бұрын

Jan, fantastic work, as usual. :) Could You tell me where did You buy that SD card angle interface and SD card to IDE adapter? Thanks a lot and all the best, Greg

@joelmarcott3282 3 жыл бұрын

Wow, a very nice solution for A600 owners. Don't beat yourself up on the locking tab, many of us have broken one, I know I have. Very delicate little things! I bought an AGA MK3 for my 1200 and I have to get a mounting tray for the HDMI as well.

@stefanocrespi5424 3 жыл бұрын

Bummer you broke the connector. Happens. Keep up the good work jan!

@JanBeta 3 жыл бұрын

Thank you! :)

@donbuche Жыл бұрын

amazing video!!

@JanBeta Жыл бұрын

Thanks! Glad you enjoyed it! :)

@srensrensen5354 3 жыл бұрын

Awesome mod 👏😃

@stevecommodore 3 жыл бұрын

Nice video good job

@johnnydreamwarior 3 жыл бұрын

Bravo Ian. Werden wier auch im nachstes eine neue auch fuhr den A1200 bekommen?

@tenterdentown2452 3 жыл бұрын

Interesting video. Do you think it would be better to make the HDMI upgrade in the style of the A520? That is to say, run a ribbon cable from the Denise chip to a socket at the rear where the modulator has been removed? That way no problem breaking the connector! Thanks for uploading.

@xsm5525 2 жыл бұрын

have 1 last question, the quality of the graphics on this certain game, does this rgb2hdmi thingy work good with the game Bubble & squeak? not sure if you've tested that game on it but the graphics on that game look great and need to run smooth.

@JanBeta 2 жыл бұрын

So far, it did work very well with everything I threw at it. I don't think I've tried that particular game but chances are that it's going to work fine just like everything else (except for the higher screen resolutions introduced with the ECS chipset--which are VERY seldomly used in games).

@12w3hji123456789 4 ай бұрын

Hi Jan, do you have the DFX file for cutting the acryllic plate for the HDMI slot?

@SunnySunGER 2 жыл бұрын

Awesome video! I do have a A600 but I can nowhere find this Adapter. Do you have any idea whre to buy this little beast?

@ClampsStalsworth 3 жыл бұрын

Jan, great video. quick question, if you are playing a very fast reaction time game, is there any noticeable lag? Not that i would ever be able to tell, but rapid fire grandchildren might.

@AmigaFanatic1980 Жыл бұрын

This is a nice and neat solution. I am looking at possibly doing something similar for my Indivision MK3 where I can use a USB plug into the smaller board, then using a flat ribbon can then direct the output to the socket as you have here. I feel this would be look more elegant (at least externally) & would free up the back port of the A1200 for other things (e.g. easier CF card hardrive access). I just wish I had a way of getting hold of the acrylic/perspex mouting plate & screws

@damienfuriet1307 10 ай бұрын

Hi, how to get only the black acrylic part instead of RF modulator ?

@MrLurchsThings 3 жыл бұрын

The limitation of OCS/ECS - is the limitation simply that of the amount of “grunt” available on the Pi0?

@JanBeta 3 жыл бұрын

Basically yes. Unfortunately the Pis with more grunt handle the GPIO pins differently and have a bottleneck there (or at least that’s what I’ve been told), so we are unlikely to see an AGA capable implementation of this project. At least as far as I know. I think the AGA chips also have different signals on the pins so this mod won’t work at all without major changes.

@tsftm4192 3 жыл бұрын

Don't worry Jan, its only a cable. We still love you :P

@JanBeta 3 жыл бұрын

Haha, thanks! :D

@tsftm4192 3 жыл бұрын

@@JanBeta You know, as I watched you struggle with tha ribbon I realised that this device is poorely designed. It could be (pcb)waaaaaaay better in a different design. No ribbon, but desoldering the RGB and have a single PCB with a DVI / HDMI out to completely replace the RGB out in front of Denise. This 2.0 version could make the mod almost factory looking, and then we could get rid of all legacy outputs RF, Comp, RGG plus that giant cap that would be useless. Someone should do this as it makes much more sense ans it only needs the Pi mounted parallel to the PCB, where theres much room from the removed HDD (everyone is using SD/CF cards anyway). Here's a mockup of how it could look. Much simpler and actually cheaper too. i.imgur.com/FfF6GwE.jpeg

@grimlyghost 3 жыл бұрын

i always wonder why every youtube cuts out the booting of the modded amigas. How much does it take to get a picture after booting the amiga? it isn´t instant anymore or am i wrong?

@PARASITSTUDIOEFFECTS 3 жыл бұрын

Love the shirt!

@mattuttley3711 5 ай бұрын

I get interface when it loads audio on my 600 using a rgb scart

@ches74 3 жыл бұрын

My colleagues all use tweezers when working with FFC\FPC connectors. I use my fingers and have never broken one which can be unfortunate because they all now come to me when they need their development kit reconfigured.

@Evert850 3 жыл бұрын

Very interesting video!! I would love to get something like this for my A600 too. I have a bunch of them but my main one that i had since childhood is almost fully kitted which means there is a Furia inside. Can that Denise adapter fit underneath the Furia? I don't really like the indivision and this seems like a perfect alternative.

@JanBeta 3 жыл бұрын

I am not 100% sure about the Furia but I think it should fit. The adapter board sits really flat on the board. I have yet to get my hands on a Furia and try.

@perhansson6718 3 жыл бұрын

There is a smaller variant that clips around the chip designed by kipper2k: eab.abime.net/showthread.php?t=105429&page=4 And then there is the original small adapter variant by c0pperdragon that you solder with wires that you can place anywhere: github.com/c0pperdragon/Amiga-Digital-Video

@Kppot 3 жыл бұрын

12:30 so where I can order that adapter? oh btw your link to pcb is broken so no first pcb for free unfortunately

@keithbeesting 3 жыл бұрын

Great video do you please have a link to where to buy the mounting plate?

@JanBeta 3 жыл бұрын

It is a custom piece that Joachim made. It’s not a very complex design, you should be able to make something similar with little effort.

@billcarson9565 3 жыл бұрын

great vid! quick question, what is the two tone grey box that is directly under your monitor? is it an oscilloscope? if so make and model please

@JanBeta 3 жыл бұрын

It’s my new Keysight scope. I made a whole video about it a while back. I absolutely love it! :)

@bartoszpucilowski4051 6 ай бұрын

Question can you still use the old RGB Output (23 pin Dsub) and connect RTC monitor along the site with or insted HDMI?

@JanBeta 6 ай бұрын

Yes, the regular video out is unaffected by the mod. :)

@andreashuber332 3 жыл бұрын

Great Video again. When I get it right only the black part of the connector is broken. Just get it out of another connector carefully and slide it in the broken one. This should do the trick

@JanBeta 3 жыл бұрын

Yes, that would be a solution. Unfortunately I don’t have any matching connectors I could salvage the part from. I just ordered a replacement, should be easy to fit.

@adriankulpa4787 3 жыл бұрын

Hello Jan. Would You mind to tell me where I can buy full hardware for this solution, please? I was trying to find a shop following your links but I failed :( ... Thank You! Great movie with great solutions! :)

@RetroGameCoders 3 жыл бұрын

This video has made me want to get an A600 ;)

@JanBeta 3 жыл бұрын

I never thought I’d ever want one back in the day. But it’s an extremely versatile and useful machine these days. :)

@RetroGameCoders 3 жыл бұрын

@@JanBeta handy how compact it is :)

@amirpourghoureiyan1637 3 жыл бұрын

@@RetroGameCoders Pi400 might be worth a look if you want convenience/value, not limited to just Amiga software either.

@RetroGameCoders 3 жыл бұрын

@@amirpourghoureiyan1637 I did a video about that :) I get real hardware for my code testing but for sure the PiMiga is fantastic

@amirpourghoureiyan1637 3 жыл бұрын

@@RetroGameCoders Should come in handy for testing :) Casual Amiga fans are better off going the emulation route, but if you're writing code then it's definitely worth having an original around!

@bufordmaddogtannen 3 жыл бұрын

What about putting the rpi in a box connected to the external rbg video connector instead, since this also happens to provide 5v on pin 23? Something like the old A520 adapter, just smaller.

@JanBeta 3 жыл бұрын

That would work but would be limited to the analog signals, similar to a standard RGB upscaler. The mod uses the digital signals provided to the Denise to generate the Full HD picture so the quality is way better.

@bufordmaddogtannen 3 жыл бұрын

@@JanBeta I see, thanks.

@EviesRevue 3 жыл бұрын

Interesting, I didn't know you could put a PLCC socket in reverse

@pawel23467 Жыл бұрын

Hallo I have question you add raspberry pi do you also get the acceleration of the pi or is it only to connect the hdmi

@JanBeta Жыл бұрын

Just the HDMI with this project. You might want to look up the PiStorm project though which is a Pi based accelerator for the Amigas. :)

@mecha7620 3 жыл бұрын

Hallo Jan, Danke erstmal für deine guten Videos. Ich habe schon lange ein Problem mit 2 meiner Amiga 600. Ich Habe immer Vertikale Streifen im Bild, und hab schon so manche Sachen ausprobiert. (Natürlich über RGB, und auch mit OSSC) Daher bin ich nun auf dein Video mit der HDMI Lösung gestoßen. Die erste Frage: Ich habe eine Turbokarte Furia EC02 die den Denise Chip verdeckt. Würde es trozdem dann passen wegen Platz usw.? Und die Zweite Frage: Hast du einen Link wo man alles Sachen kaufen kann dazu in einem Set? Danke schon mal für die Antworten. Gruß Matze

@amirpourghoureiyan1637 3 жыл бұрын

I wonder if it's possible to merge this project with the PiStorm? The Pi 4 should have enough power to do both, but GPIO pins being used on both projects might complicate things...

@kurbeco 3 жыл бұрын

Work is in progress; linuxjedi.co.uk/2021/06/13/this-week-in-pistorm-2021-06-13/

@ANKH123 2 жыл бұрын

Hi. It's possible to mount on A1200 ?

@JanBeta 2 жыл бұрын

No, the AGA Amigas use a completely different video circuit and the Pi would not be able to handle the bit depth of the AGA modes even if you could get the necessary signals from the Amiga (which would be a bit more elaborate than plugging a socket between some chips). You can obviously still convert the RGB output using the general purpose version of the RGBtoHDMI externally. But that’s using the analog signals so it’s not going to be as crisp.

@stephenvalente3296 3 жыл бұрын

Just need one for the A1200 now

@brostenen 3 жыл бұрын

That would take a completely different type of hardware. As a PI is not capeable to handle AGA.

@ITGuyinaction 3 жыл бұрын

🤔🤔🤔🤔 You are very skilful guy!

@MultiArrie 3 жыл бұрын

new video of Jan, repair of the elektra beckum welder pcb has to wait.

@robertbrown7478 3 жыл бұрын

Where did you get the acrylic mounting plate from?

@JanBeta 3 жыл бұрын

It is a custom piece that Joachim made. But it is not too difficult to make something simpler from a piece of plastic yourself I think.

@erik78bg Ай бұрын

Hi, where can I find the support where you glued the HDMI output and then screwed it to the Amiga? Thank you

@JanBeta Ай бұрын

It's a custom piece that one of the project creators routed for me. I don't think it's available anywhere but it should be relatively easy to make something similar yourself.

@erik78bg Ай бұрын

@@JanBeta ah ok, thanks

@kipper2k 3 жыл бұрын

the problem with plcc clip ons is it can interfere with any accels attached to the cpu and the hat (even with the hole) will cause the denise to heat up if the airflow is restricted

@krnlg 3 жыл бұрын

I wonder if a PLCC pass-through board would be possible - same as with a DIP chip pass-throguh but using PLCC sockets. It should not be all that difficult to solder or desolder a PLCC chip like the Denise - though certainly a higher barrier to entry than doing the same with DIP chips. But I don't know if a 'male' companion to a PLCC socket exists?

@kipper2k 3 жыл бұрын

@@krnlg github.com/c0pperdragon/Amiga-Digital-Video/issues/37

@awilliams1701 3 жыл бұрын

I've thought about replacing the C64 RF modulator with a modern replacement (that doesn't do RF at all) but I don't know if my $30 soldering iron and desolering pump kit can pull it off. I had a hard enough time replacing the power switch.

@xxycom8963 3 жыл бұрын

Use “Low-melt” solder, to desolder.

@awilliams1701 3 жыл бұрын

@@xxycom8963 didn't know that was a thing. I just ordered solder. No idea if it's low melt or not. I do know I was using shit flux. I have better flux now. Maybe it will help.

@bitoxic 3 жыл бұрын

Nice T-Shirt @JanBeta! 😁

@JanBeta 3 жыл бұрын

Thank you!

@dimitrycus 3 ай бұрын

Use of 4 core SBC for hdmi video output is a crazy thing!!

@alanhaynes4576 3 жыл бұрын

Might have been a good idea to attach the flat ribbon cable to the HDMI connector before securing it in place. Thanks for the video.

@JanBeta 3 жыл бұрын

Yes, indeed. I‘m definitely going to do that when I get the replacement part. :D

@minombredepila1580 3 жыл бұрын

Wonderful solution, pity Amiga 600 are so expensive. I guess you'll have to reset the "counting days without accidents" plate on the wall, as you broke the HDMI connector :-))))

@JohnnyReb1976 3 жыл бұрын

Now, would that Denise bit fit under a Furia?

@joachimfirnhaber8729 3 жыл бұрын

Yes it fit under the Furia

@stevesether 3 жыл бұрын

Any chance there's somewhere t put an HDMI out on an A500? That monochrome plug was always fairly useless, though I don't know if an HDMI socket would fit.

@JanBeta 3 жыл бұрын

I think you can run a flat flex through the cooling vents and 3D print a little enclosure for an HDMI socket. You would have to cut the case to have a real internal solution for the A500 though I’m afraid.

@nospammichik 3 жыл бұрын

Geht es nur meinem Amiga 600 so, oder wird der Denise bei Deinem 600er auch so warm / fast heiß? Ich frage nur deshalb, weil ich mir auch so ein RGBtoHDMI bauen will, aber Bedenken habe, weil der Denise so warm wird und unter dem PLCC Sockel dann ein Wärmestau entstehen wird.

@JanBeta 3 жыл бұрын

Denise wird im normalen Betrieb bei mir auch recht warm. Die Chips können aber auf jeden Fall einiges vertragen und ich denke, auch mit dem Mod bleibt das alles im Rahmen. Ich konnte nach stundenlangem Betrieb keine zu hohen Temperaturen feststellen. Joachim hat bei der neuesten Version des PCBs auch die Lüftungslöcher nochmal vergrößert, damit es da keine Komplikationen gibt.

@robbune1792 Жыл бұрын

Hi Jan - are you sure that you broke the adapter? I can't get the the video output to work with a flat flex cable and I have read of others a having similar issues. I've replaced the flex cable and adpaters but still no output unless I plug directly into the pi with an hdmi cable.

@JanBeta Жыл бұрын

Mine works without any problems after I replaced the connector. Are you sure the flat flex is fully inserted and locked into the connectors and in the correct orientation etc? It‘s literally just an extension of the original connector on the Pi so that’s the only explanation I can think of why it wouldn’t work. 🤔

@robbune1792 Жыл бұрын

@@JanBeta as in your video I have the silver connectors facing up as I connect. The connection feels snug and tight once locked in place so it really is weird. i guess it is not possible to blow something if the cable orientation is wrong.

@robbune1792 Жыл бұрын

@@JanBeta so it seems that the problem is the female hdmi adapter which the monitor cable plugs into. I switched this out for a different type and now the signal works. The problematic adapater is a slightly different type, it has a hinged clip which close down on the cable as opposed the type used in your video with the two clips either side of the cable. I need this type of adapter as it is slimmer and fits the 3D printed caddy I have. Likely I have been sent a defective part I guess.

@prb366 Жыл бұрын

@@robbune1792 I'm planning to do this mod to my Amiga 600. The only part I can't get hold of is the HDMI mount. You mentioned a 3D printed caddy for the HDMI port. Could you please let me know where I could find the files (STL, OBJ, etc) to get one of these 3D printed myself?

@totoonthemoon3593 Жыл бұрын

Will be nice to have a RTG embedded into the Pi to display both video source on the same output.

@brostenen 3 жыл бұрын

Nice... I love the denise adaptor. Can it perhaps fit under a Furia-020?

@JanBeta 3 жыл бұрын

I think it is designed to leave enough room for the Furia (it sits very flat on the chip). I don’t have one to test though.

@brostenen 3 жыл бұрын

@@JanBeta Hmmmm... I asked about the possibility of doing a socket adaptor like this, just for ScanPlusECS scandoubler, in the past. You know, the one that uses a dip socketed denise on top. (Sandwich solution). Back before individual launched their IndivisionECS-V2 scandoubler. And people said it was impossible, because of space and all that. It is to give the 600 a second scandoubler solution. If the ScanPlusECS takes the Denise on top, and the RGB port are still working, then it must be the signals just being hooked uo to the pins, and therefor it should be no issue if the scandoubler is before or after the denise chip. But I did not design anything, because I can not design PCB's and I have no experience in that. So it is just an idea that I had back then. I am still curious if a Furia will fitt on top. That would make an Amiga600 really awesomme. Just imagine.... Furia-020 RGBtoHDMI 2mb ChipRam (individual computers) Floppy internally Gotek externally IndivisionECS-V2 Angled IDE/CF with 44 pin port Mikrodrive HDD drive CD (ribbon cable through PCMCIA slot)

@CollinBaillie 3 жыл бұрын

Is the blue (window border) in Workbench a little off? Did you tweak it after the initial bring up clip?

@JanBeta 3 жыл бұрын

Oh, I think I just changed the workbench preferences overscan settings. I had this connected to a CRT the last time I used it. The position and size of the wb screen can be changed easily.

@CollinBaillie 3 жыл бұрын

@@JanBeta Apologies, I was meaning the colour. Compare the blue of the window when using your cheap upscaler to the blue when using the Pi. The Pi output looks purple.

@JanBeta 3 жыл бұрын

Oh, okay. The color of the window top bar is set to purple actually. The color looked the same with the upscaler and the RGBtoHDMI. Maybe the white balance of my camera played some tricks, it doesn’t work too well for filming monitors.

@CollinBaillie 3 жыл бұрын

@@JanBeta I checked it out again... they're both purple. 😜 Guess my brain filled out the standard blue when I started watching.

@paulyoung823 2 жыл бұрын

Hi Jan, I have tried to DL the Gerber files for the A600 Denise PCB to have a PCB made. the Store i am using has asked me for a sequence. Could you please help with this ?

@vitoamoroso7624 2 жыл бұрын

I'm also trying to understand how to have this item, trying to contact IanB but nothing...I am very sorry not to be able to participate in this project, there is not all the necessary information for people who do not have high technical skills, and no help in the forums or anything else ... I think I will have to give up

@paulyoung823 2 жыл бұрын

@@vitoamoroso7624 hopefully i can get sorted. If i do i will let you know as i would be able to get an extra one made for you.

@vitoamoroso7624 2 жыл бұрын

@@paulyoung823 thank you very much :-)

@RainerK. 3 жыл бұрын

A600 ❤

@stevenross-watt8640 Жыл бұрын

Do you know anywhere that has this available as a kit for sale? All I see is sold out. Thanks. :)

@JanBeta Жыл бұрын

Unfortunately I don’t know any place that sells these. Maybe you could try contacting the creators in the forum?

@turbolenza35 3 жыл бұрын

Is there input lag?

@JanBeta 3 жыл бұрын

Extremely little! I was not able to measure it with the equipment I have at least. Let alone notice it while playing games etc.

@tarzankom 2 жыл бұрын

Those damned ribbon cable connectors are the bane of my existence. I can never get them right without breaking them at least twice.

@williefleete 3 жыл бұрын

I’m guessing you had the ribbon around the right way, IE the metal fingers contacting the pins in the ZIF socket

@JanBeta 3 жыл бұрын

I put it in there the wrong way around at first, but reversed it later to no avail. I actually edited out a longer segment of me swearing and trying to make it work… :D

@jedrula77 2 жыл бұрын

Nice relly nice ideas for old computers. Little tip, dont use double side tape for secure HDMI port in this acrylic adapter. Because glue on tape can easy melt after use in hot case, and huge fat HDMI cable can easy lift glued HDMI port and made big mad devastation inside case. Or if have luck only destroy signal tape. I see many HDMI ports soldered and lifted from PCB. Better use hot glue or best some acrilic glue or best way any 2 ingrediens nonconductive glue. Glues like 1s Super Glue can made shorts or another disasters. Hot glue is very safe and can easy dismount with hot air. Grettings and cherrs :D

@JanBeta 2 жыл бұрын

Thanks! Good point about the double sided tape. I‘m going to look into adding something more permanent next time I open the A600. :)

@angrydove4067 3 жыл бұрын

Is that blood on the keyboard connector?

@JanBeta 3 жыл бұрын

No, I used a red marker to mark the direction it goes in when I desoldered it during recapping. :)

@ArcadeFan77 3 жыл бұрын

1:27 What I really dislike about this upscaler is the image clipping on the right side. In overscan games, the frame is cut off. It cannot be corrected in any way.

@JanBeta 3 жыл бұрын

That’s definitely a caveat. These don’t handle overscan screen modes well. Other than that I’m really pleased with the RGBtoHDMI.

@atatu4551 3 жыл бұрын

i have waiting for hdmi4a600, thanks

@msthalamus2172 3 жыл бұрын

Have to admit I wasn't expecting to see someone halfway across the world wearing a Bikini Kill shirt! :) I thought they'd only ever really gotten big in my region.

@JanBeta 3 жыл бұрын

I heard about them in the context of Nirvana and I’ve been a fan ever since I first listened to their music. :)

@mattuttley3711 5 ай бұрын

Guess if you've got a cf card on the ide adapter inside and a ram card in their too then not much chance fitting this inside as well

@JanBeta 5 ай бұрын

I have a memory expansion, a cf adapter and an accelerator in this A600, the RGBtoHDMI fits just fine.

@michaelmadsen4923 8 ай бұрын

In hindsight, you probably should have inserted the flat flex cable to the HDMI out board, before you stuck it down on the acrylic part 🙂

3 жыл бұрын

Hm... Ist das eine gelbe Sunnyline-Maus, die mir in meiner "Farbsammlung" noch fehlt, oder ist das einfach nur der übliche Gilb-Farbton der im Video etwas mehr shiny aussieht, als er eigentlich ist?

@JanBeta 3 жыл бұрын

Ist tatsächlich eine gelbe Sunnyline. Die gebe ich allerdings nicht her, war die letzte Maus die ich „back in the day“ an meinem A2000 benutzt habe. ;)

3 жыл бұрын

Ach, kein Problem. Ich wusste nur bisher gar nicht, dass es die Maus auch in Gelb (nicht "Gilb") gab, aber da kann ich mich ja nun auf die Suche machen ^^

@DeathMetalDerf 3 жыл бұрын

I LOVE the shirt, Jan! Bikini Kill is fantastic!!!!!

@JanBeta 3 жыл бұрын

They are!

@helgew9008 3 жыл бұрын

Why can the RGBtoHDMI unit not simply be connected to the factory video port?

@DavePoo2 3 жыл бұрын

By the time the video signal gets to the port it has already been converted to analog RGB. The Denise outputs the digital RGB, so the signal gets converted to HDMI without ever being turned into analog. If you took the output from the video connection, it would be no better than the signal you get from the SCART to HDMI converter.

@gertsy2000 3 жыл бұрын

Whoopsies. I can't remember if I was thinking you should connect the flat flex cable to the HDMI socket before you stuck it to the mount. Perhaps you needed instructions Jan?

@ventrue6516 3 жыл бұрын

Next video should be about HDMI module for C64 :)

@JanBeta 3 жыл бұрын

There is a VIC-II replacement in the works actually. I’m very likely going to make a video about it when the project is finished and I get my hands on one. :D

@ventrue6516 3 жыл бұрын

@@JanBeta I'm looking forward. ;)

@josephlunderville3195 3 жыл бұрын

Double sided tape doesn't work well for long term mounting in my experience because it tends to be very temperature sensitive -- tape adhesive gets brittle and loses its stick when it's cold, and it melts when it's hot, and even at the best of times it tends to creep and gradually let go if subjected to any significant force. A really good quality tape can work for lightweight things that are at room temperature all the time, but especially if you're sticking down electronics like a Pi which will get warm and melt the tape adhesive, I can't recommend it -- hot glue, silicone, and zipties are my go-tos now for electronic parts inside a case if I'm not doing it properly with screws. There are tape adhesives that can work over larger temperature ranges for longer times but in my experience they're really hard to remove and then I might as well be dealing with glue...

@TeeborGames 3 жыл бұрын

Time to update the sign on the wall there?

@JanBeta 3 жыл бұрын

Always! :D

@xsm5525 2 жыл бұрын

will it work with a furia 020 card?

@JanBeta 2 жыл бұрын

Yes, I have a Furia in my A600 now myself. Works flawlessly and fits physically without any issues.

@xsm5525 2 жыл бұрын

@@JanBeta ah thanks for letting me know :)

@IntenseGrid 5 ай бұрын

Do these do ECS resolutions yet?

@JanBeta 5 ай бұрын

They somewhat do, but not 100% perfect. Resolution is a tiny bit reduced for the very high res modes because the bit depth is marginal.

@overdrive39 3 жыл бұрын

Do you repair Amigas I have a Amiga 2000 that needs help.

@JanBeta 3 жыл бұрын

I can’t do contract work unfortunately. Lack of time and proper education in the field. I also don’t have proper insurance for it so I only work on my own devices or do repairs for close friends and family. Sorry!

@j.t.4255 2 жыл бұрын

Hi Jan wo bekommen ich denn die Acryl Basis Plate her?

@JanBeta 2 жыл бұрын

Die gibt es glaube ich nicht öffentlich zu kaufen. Ist eine selbst gefräste Spezialanfertigung von Joachim.

@j.t.4255 2 жыл бұрын

@@JanBeta Danke ich schau mal ;)

@Zhixalom 3 жыл бұрын

I may be wrong but as I understand it, the RF-Modulator also generates the composite video signal. So you might as well remove the yellow RCA plug next to it... and I guess the remaining hole could very conveniently be used for the RGB-to-HDMI's menu button, extending the microSD/TF reader for the Pi-Zero or both, maybe? - Jan, I have already successfully build an RGB-to-HDMI into my friends A500... and would now like to try it with my Commodore 128's 80 column display. But the more I look at hoglet67's RGB-to-HDMI github page, the more confused I just seem to get... on what version and/or adaptor board (and so on) to get. - I can't seem to find any YT-videos or step-by-step guides on it. So, I would really love if you would consider making a similar video for the C128.

@DavePoo 3 жыл бұрын

The composite video is generated by the chip at U12 (CXA1145 Encoder), it's output is fed to both the modulator and the yellow RCA composite jack. The composite should still work fine without the modulator.

@davidegalliussi1979 3 жыл бұрын

I desire a vicII cheap rgb out and this for the hdmi out ..and all the Commodore smiling crisp

@DavePoo2 3 жыл бұрын

Unfortunately the VIC-II doesn't actually produce RGB, but check out this VIC-II replacement that can do pure digital output kzfaq.info/get/bejne/jch4iZRe2dbPk5s.html

@neophytealpha 3 жыл бұрын

A UV blocking coating after retrobriting could help it last longer.

@stephenbruce8320 3 жыл бұрын

Your not alone in the mistake department we all have been there and anyone who says they don't make mistakes has absolutely no credibility. The flat flex idea is pretty nice but if your always working on your Amiga its maybe not the best solution and a short cable would be better. You could have PCBWAY make up a PCB where you can solder a couple HDMI Connectors on the board and then using those same two holes mount it. Kipper2K has a VGA Board for the A600 that had a VGA Connector and a JTAG connector for connecting to the Indivision Board. I have one in one of my A600's and I would love to have a couple more but gave up looking for them. Only problem with PCBWAY and I do use them is the cost of shipping other than that they are great.