ARB Twin Air Compressor Install in 3rd Gen Tacoma

Рет қаралды 4,371

Күн бұрын

In todays video we will have a look at how I installed my ARB Twin Air Compressor and ARB Manifold Kit in my 2017 Tacoma using a mount from Rogue Off Road.
Products discussed in this video:
Air compressor: amzn.to/3ASMEh7
Mainfold kit: amzn.to/3AABOw4
Tire Inflation Kit: amzn.to/448E6Qo
Digital Tire Pressure Gauge: amzn.to/3VaegHN
Rogue Off Road GTFO Expedition Bracket: rogue-offroad.com/GTFO-Expedi...
More on ORYX:
Website: offroadyota.com/
Instagram: / offroadyota. .
Facebook: / offroadyotax. .
00:00 Intro
01:06 Overview
04:53 Wiring
07:19 Installing Compressor and Manifold onto mount
12:07 Installing braided hose and air fitting
16:23 Install in truck
18:02 Wiring in truck
18:25 Install review
21:15 Outro

Пікірлер: 17

@AntonioClaudioMichael 10 ай бұрын

Great install video just got this setup for my 2007 v8 4runner my bracket is a M.O.R.E. Bracket That also months the 1 gallon arb Tank as well I'm installing the Inflation kit and the lockers also though

@offroadyotaxploration 10 ай бұрын

Thanks. That is also a great setup that I considered. In the end I decided against the 1G air tank and wanted a bit more clearance above the compressor. Thanks for the comment.

@AntonioClaudioMichael 10 ай бұрын

@@offroadyotaxploration yvw good video

@taylorjackson8948 10 ай бұрын

Nice install!

@offroadyotaxploration 10 ай бұрын

Thank you!

@MrXjarodx 9 ай бұрын

Can you show how you wired your switch up? Did you run the purple cable to a relay?

@offroadyotaxploration 9 ай бұрын

The purple cable runs straight from the compressor to the switch. then I ran power and ground to the switch. I believe the compressor has a built in relay. It gets wired directly to the battery, so no need to run a relay on the switch cable.

@MrXjarodx 9 ай бұрын

thank you! @@offroadyotaxploration

@chas8008 Жыл бұрын

what was with the diode?

@offroadyotaxploration Жыл бұрын

I used it on the wire that runs from the power source to the switch. It only allows the current to flow in one direction. As it was included in the harness I assumed it may be necessary, so I made sure to include it in my configuration.

@chas8008 Жыл бұрын

Ok good deal

@sergey4000 8 ай бұрын

👍

@offroadyotaxploration 8 ай бұрын

Thank you

@alexalanis4830 6 ай бұрын

Is the manifold required?

@offroadyotaxploration 6 ай бұрын

No, you can run the hose straight to the compressor. If the compressor runs for a long time though, the hose will get quite hot.

@alexalanis4830 5 ай бұрын

So are you using the manifold simply for convenience? @@offroadyotaxploration

@offroadyotaxploration 5 ай бұрын

I am using the manifold to preserve my air hose. At times i use the compressor to fill up multiple vehicles in a row, which could cause enough heat to break a plastic hose.