Рет қаралды 35,119
We'll go over setting up a new Raspberry Pi 4 and getting Home Assistant up and running in this one. See below for relevant links:
*DOWNLOADS*
balenaetcher: www.balena.io/etcher/
Home Assistant Image: www.home-assistant.io/hassio/...
*JOIN OUR HOME ASSISTANT GROWING FORUM*
ledgardener.com/forum
- All Amazon links below are affiliate links, which means LEDgardener receives a commission from Amazon if you make a purchase after following the link, at no extra cost to you. Thank you for supporting the channel!
*PARTS IN VIDEO*
Raspberry Pi 4 Kit I'm Using: amzn.to/2XdSM0h
**MY GARDEN AUTOMATION SYSTEM**
**CONTROL BOX**
BUD Industries NBF-32026 Plastic ABS NEMA Economy Box with Solid Door, 15-47/64" Length x 11-51/64" Width x 6-9/32" Height, Light Gray Finish:
amzn.to/2XnDMgD
Plastic Internal Panel to Mount Gear:
amzn.to/2VbwtG4
Panel-Mount AC Connector for Box:
amzn.to/3c75OB9
Nylon Standoffs:
amzn.to/3b3fDA4
Cable Glands for Passing Cable In and Out of Control box:
amzn.to/2VotryG
** CONTROL BOX MISC ELECTRONICS **
Amazon Fire Touch Panel Tablet:
amzn.to/2JWE2eN
Right-angle Micro USB Cable for Tablet:
amzn.to/3efeTdk
Mean Well 12VDC Power Supply:
amzn.to/2JUHd6B
Drok Voltage Stepdown Converter with Readout:
amzn.to/2RqgP91
Dupont Cables:
amzn.to/2yQio9M
Breadboards:
amzn.to/3e4jM8K
Screw Terminal Blocks:
amzn.to/2x9F2tl
8 Channel Relay Board:
amzn.to/2JR01DX
** DEVELOPMENT BOARDS (CONTROLLERS) **
You can also use other hardware, check out this page for a good writeup:
smarthome.university/home-ass...
Arduino Mega:
amzn.to/3eaeNDr
ESP32S WiFi Development Board (Handles WiFi communication between control box and Home Assistant server as well as from inside tent to Home Assistant server):
amzn.to/2JSNdgb
Whitebox Labs Tentacle Shield to Add Atlas Scientific Gear to an Arduino and provide electrical isolation of probes (pH probe needs to be isolated from EC probe):
amzn.to/3aYVzPl
** SENSORS **
BME280 Temperature/Humidity/Pressure Sensors for Tent and Control Box:
amzn.to/3ed8hMb
Waterproof Temperature Sensor for Nute Reservoir:
amzn.to/2yQ8cy2
Atlas Scientific Conductivity Kit K 1.0 5-200,000 μS/cm:
amzn.to/39RFSIo
Atlas Scientific pH Kit 0-14 pH:
amzn.to/2JQVKQV
Moisture Sensors:
amzn.to/34BumA1
Catch Basin Float Sensor:
amzn.to/2XotuNj
** PUMPS AND SOLENOIDS **
Peristaltic Pumps:
amzn.to/3a1UWDg
Motor Drivers to Control Peristaltic Pump Speed:
amzn.to/2yR2MCX
Tubing for Peristaltic Pumps:
amzn.to/2UYHDzc
Nutrient Res Stirring Pump:
amzn.to/2UYGQhI
Nutrient Fertigation Pump:
amzn.to/34qHrM7
Normally-Open 12V Solenoid (Allows water to flow into system until solenoid is activated, which closes it - used for flood protection. Requires 12VDC power supply and 1/4" spade connectors):
amzn.to/3el7qJI
1/4" Spade Connectors:
amzn.to/3efd3Js
Normally-Closed 12V Solenoid (Restricts water between RO res and Nute Res, requires pump in RO res to push water through it):
amzn.to/3aUnyzA
Pump to push water through solenoid:
amzn.to/2UYGQhI
** NUTRIENT JAR STIRRING SYSTEM **
Nutrient Jar Stirring Fans:
amzn.to/2JT0PYR
Nutrient Jar Magnetic Stir Bars:
amzn.to/3aUleZo
Nutrient Jar Magnets:
amzn.to/3aZl4jp
Nutrient Jar Superglue (I used LePage but I don't think it's available in the States so this should work):
amzn.to/3ebdHYb
** RESERVOIRS **
Reservoir Totes:
www.homedepot.com/p/HDX-27-Ga...
1/2" Double-Threaded Bulkhead for Connections to Reservoirs:
amzn.to/2yHAcnh
1/2" Tubing to go between reservoirs and out to plants:
amzn.to/3a0epEp
Sharkbite swivel to attach tubing between 12V solenoid on RO res and 1/2" float valve on nute mix res (requires wormdrive clamp to secure hose to fitting):
amzn.to/2JVwR6s
Wormdrive Clamp:
amzn.to/2Xq5bif
Nut Res Fill Float Valve:
amzn.to/2yIs7yG
1/4" Float valve for DIY Humidifier and RO Res:
amzn.to/2xmtBOX
DIY Weigh Scale Kit for Reservoir:
amzn.to/2RI1BfN
** MISC **
WiFi-Controlled AC Plugs:
amzn.to/3csgVVs
DIY Humidifier Ultrasonic Discs:
amzn.to/39TySKV
Reverse Osmosis System:
amzn.to/2x9MRze
Wire Rack:
www.homedepot.com/p/HDX-72-in...