Hey Gavman, yeah, I seen your vid ages ago when you measured your sx82. Yes both sx82 & sx92 are the same 50mm cylinder, just different stickers. Hows yours going. Thanks for watching.

@@anthonysgarage5283 at the moment the sx82 is selling for $50 less than the 92 on eBay, is there really no difference?

@@janramonmartin they have different stickers, other than that, appear to have same specs but you should read both closely . Maybe contact Edisons, see what they say? Thanks

@@anthonysgarage5283 SX92 has greater volume for oil and fuel capacity.

Hey Brandon, I'm no expert at tuning or running chainsaws, their ok fo the money, but your not missing much. From what I've seen holtzforma G372 XP is equivalent with better bucking dogs, I made custom dogs for mine. G372 XP is available in US. Thanks for watching.

Hi Alessandro, I searched ebay for this particular cylinder & piston from different sellers. Saw doesn't get a lot of use but is running even better now since running in. I Ran 28" bar fully in hardwood no problem, muffler mod also helps. After purchasing these, I found you can get, 48mm for 65cc, 50mm stock, 52mm big bore & 52mm big bore with pop up piston for even higher compression from hywayparts.com I have since purchased 52mm pop up from hywayparts.com Looks good but not used yet. SX82 is Husqvarna 372xp clone. Hope this helps.

If I was to choose out of sx82 or sx92, it would be sx82, all Chinese saws will have some issues, these ones, be gentle with chain tensioner & always use decompression valve & yes they all leak bar oil. Have never used Alaskan saw mill, I think they can be tough on saws because of long cut time & cutting end grain, take it easy, try cut a bit of an angle, less end grain cutting.

Hi Brogan, second hand 372xp here in Australia is similar, maybe more, if you can find one. my saws are 3 & 2 years old. They leak bar oil, log spikes/dogs are crap, I made my own. chain tentioner will fail from poor quality material, be gentle, mine are still working. mine came with .063 gauge chain which jammed when tightening side cover, I fixed this or you could run .058 gauge chain but it will be looser in bar. otherwise pretty decent saws. cost was $207 & $159 delivered through ebay. currently priced at $289 for Baumr-ag sx92 or $259 for sx82 which is basicly the same saw but I don't think the seller (Edisons) does international shipping. you can find a G372xp, which is similar saw with better log spikes/dogs at www.farmertec.com you can also see correct specs. big bore cylinder with flat top or pop up piston also available at www.hywayparts.com Thanks for watching.

Hi BigBird, yes my sx92's leak oil, sometimes quite badly. as far as I Know, all chinese chainsaws leak bar oil. I empty mine after use, preferably while still hot so oil drains easily, almost like water. Don't expect any help or service from Edisons, They will brush complaints under the carpet as they TRIED to do with their 92cc claim. food for thought, a while back I picked up an old 1st gen sx62 at the markets for $15, almost unused. took it home, found fuel leak, fixed it. then found massive oil leak, leaking out almost as fast as filling up. found the hole in oil tank for hose to pump was too large. used epoxy putty to fix. no more leaks😊 BUT!! Now oiler doesn't work😒 as there is now a vacuum lock. added breather now all working😊. I haven't seen a breather on sx92 either. Thanks for watching👍

@@anthonysgarage5283 Yeah I have done the same thing only after it left a large stain on the garage floor :)

Hi Kevin, thanks for the invite, great idea about friendly competition. I'll try get involved but can't promise. Weekends are full right now. I just watched your video's, the sx62 sounds good. Keep up the good work. Cheers. Anthony.

Filipe Coelho. I would prefer to own genuine 372xp rather than crappy Chinese clones but even old 2nd hand 372xp in Australia will cost $700 if you can find one. New husqvarna eguivalent costs $1500 -$2000. Both of these cost me less than $370 total. Thanks for watching.

@@anthonysgarage5283 I am Portuguese In Portugal, a new 372xp x torq genuine, at the moment, at the brand representative, costs 600 euros, equivalent to 976 Australian dollars, that's why I commented that way, I had no idea that this type of machines was so expensive there. I'm really sorry.

@@dmc2537 Hi Filipe, no problem, apology accepted, At that price I would save the extra money for genuine Husqvarna. Sounds like not only do you live in a beautiful country, you also have cheep chainsaws😆. I did a search, found 372xp x torq here $1889.90 free delivery. Cost of living in Australia is quite high. Thanks again for watching👍