Bevel Gears Milling.

Рет қаралды 39,541

3 жыл бұрын

See the milling of spur-toothed bevel gears on a amateur milling machine. The presented procedure is time-consuming but works fine in the home workshop.
#lscad

Пікірлер: 65

@somalia5019 Ай бұрын

New subscribed from Somalia thanks

@prof-rieg 26 күн бұрын

Thank you very much! And greetings to Somalia!

@a-k-jun-1 6 ай бұрын

This was an amazingly informative video about bevel gear machining on manual machines. Thank You for showing this operation. From Alaska, USA

@prof-rieg 6 ай бұрын

Thank you very much. Greeting to Alaska from Germany!

@steveallarton98 2 ай бұрын

Brilliant demonstration of the method described in Ivan Law’s book. I’m just about to try it on my Myford Super 7 lathe, with the Myford dividing attachment . . . . Kind regards, Steve A.

@prof-rieg 2 ай бұрын

Thanks a lot and good luck!

@fredtoledo2607 3 ай бұрын

The best video and detailed and easy to understand. Thanks LSCAD for sharing. Very much appreciated. Your subscriber from the Philippines. More power.

@prof-rieg 3 ай бұрын

Thank you very much!

@gshizas 3 жыл бұрын

perfect work,regards from Greece!

@prof-rieg 3 жыл бұрын

Thank you and greetings to Greece!

@johnbird8605 11 ай бұрын

Great video, very well explained. Thank you!

@prof-rieg 11 ай бұрын

Thank you, very kind of you!

@223mike 8 ай бұрын

And a lovely little Myford!!! Great video! I have to make a pair for my 1/3 scale mill engine!

@prof-rieg 8 ай бұрын

Thanks a lot!

@theworldisflat. 3 жыл бұрын

Great video,thanks a lot.

@prof-rieg 3 жыл бұрын

You are welcome!

@jimsvideos7201 9 ай бұрын

Thank you for the lesson!

@prof-rieg 9 ай бұрын

Thank you for your comment!

@compassprecision 3 жыл бұрын

Great video. Loved all the closeup shots. Just subscribed :)

@prof-rieg 3 жыл бұрын

Thank you very much - you are welcome!

@TrPrecisionMachining 3 жыл бұрын

very good video..thanks for your time

@prof-rieg 3 жыл бұрын

Thank you very much!

@441rider 2 жыл бұрын

I have a Stuart Sirius kit that has a bevel gear. Never got time to build it so it's collecting dust. Nice work on the Number 1 Stuart!

@prof-rieg 2 жыл бұрын

Thank you!

@moazzeid5421 10 ай бұрын

Great video, well explained, nice work

@prof-rieg 10 ай бұрын

Thank you very much!

@titojomzvlog6203 3 жыл бұрын

Thanks for tips

@prof-rieg 3 жыл бұрын

you are welcome!

@davebrown1697 2 жыл бұрын

Great work I'll have to try it. Subscribed

@prof-rieg 2 жыл бұрын

Thank you - you are welcome!

@sirknowitall123 2 жыл бұрын

thank you very helpful

@prof-rieg 2 жыл бұрын

You are welcome!

@magnusklahr8190 Жыл бұрын

Realy good video!

@prof-rieg Жыл бұрын

Thank you very much!

@laercioribeirofilho7913 3 жыл бұрын

Vielen Dank! Ich bin Brasilianer. Das Video ist ausgezeichnet und beschreibt ein Thema, das nur erfahrenen Maschinisten vorbehalten ist. Ich hatte es bereits aus dem Deutschen übersetzt, aber ich habe es einfacher als Englisch.

@prof-rieg 3 жыл бұрын

Vielen Dank fuer Ihre Rueckmeldung und Gruesse nach Brasilien!

@ernerstowerdum3942 9 ай бұрын

Excelent video

@prof-rieg 9 ай бұрын

Thank you very much!

@slicktires2011 2 жыл бұрын

If you show me how to machine hypoid gears in a manual mill I'll be forever grateful!

@tariqhaki7597 4 ай бұрын

Great work.. Can I make a 23 tooth gear differentially without using the number 23 or its multiples?

@prof-rieg 4 ай бұрын

Thank you very much! Yes, please see my video #195.

@arturvelten9039 2 жыл бұрын

Thanks for sharing. But this are no bevel gears…

@narendraingale358 2 жыл бұрын

Gear cutting karne mai problem hai to help milegi kya sir...?

@chauvinemmons Жыл бұрын

I too prefer the sound of the machine some of the other comments I don't even know where to begin other than somebody didn't have anything better to do human beings are a petty worthless lot to begin with those with the least intelligence or the most intelligence often make the most trouble especially if they have no practical experience. Sometimes it's best to know only enough to be motivated and productive that's where the most fun can be found. Learning comes from making it over because of some minor detail you are not aware of and therefore overlooked.

@prof-rieg Жыл бұрын

Thank you very much for your feedback!

@paulosoarescarvalho6219 20 күн бұрын

Hi, is this method also good to do small bevel gears? Example: daa= 13mm and M0.8 cutter? Thank you

@prof-rieg 20 күн бұрын

@@paulosoarescarvalho6219 yes, I guess so

@paulosoarescarvalho6219 14 күн бұрын

@@prof-rieg I'm strugling with this formulas... Can you help? The question is i need a bevel gear for 2 shafts at 90º transmission. I found at Aliexpress a bevel gear that is advertised as 15T M0.8. And here starts the problem. By the formula you use "d" should be 12mm (0.8x15=12), but is not. Also "dai" by formula should be 13.13mm, but is only 8.41mm. Also "daa" should be 20.13mm (for "b=3mm), but is only 13.13mm. What am i missing? I bought from Aliexpress this bevel gear and they work very smooth, but unfortunately they are not hardened and i would like to do by my own same gears and then do some heat treatment to make them hard. I already tried but i can't make them so smooth as the original one. At Aliexpress the seller have a draw. If you could take a look and give some help i would aprecciate a lot. Here is the link to the bevel gears: www.aliexpress.com/item/1005005119203188.html?spm=a2g0o.cart.0.0.55bc38daDI7KNO&mp=1 Thank you for your attention and also for this great lesson!

@paulosoarescarvalho6219 12 күн бұрын

@@prof-rieg Hi again, it seems not... I did an experiment with all this formulas you presented. I put them on an Excell sheet in order to get the results you show. It worked fine and now i only need to play with "m", "z" and "b" parameters from your draw. In this way i can get a general view of all gear and the relation between measurements and how they behave when you change one of those parameters. Very usefull to draw a gear respecting this math. But now and for the gear i need, with "z"=15 theeth, "m"=0.8 and "b"=3mm i get a result for "dai"=13.1mm and "daa"=19.1mm. And here is the problem! Because the gear i need must have "daa"=13,1mm and "dai"=8.4mm. This means if i use this method to cut this gears it will not work. The gear i need is sold at aliexpress and i bought 1 pair. They have a precise fit and run very smooth, but the problem is, they are not hardened, so i need to do by myself this gears. You can see at aliexpress this gear where ths is also the corresponding draw. This is the link: www.aliexpress.com/item/1005005119203188.html?spm=a2g0o.cart.0.0.391138dakGBFy6&mp=1. Now i gess there is another way to cut this small gears. I saw at youtube some people cuting bevel gears using diferent angles. It seems they use complementary angles. They cut the piece on lathe with one angle and then use a diferent angle on milling machine. Example: on lathe cut 48º21´ and on milling machine 41º18´. The total angle is 89º39´ very near the 90º and seems to work very well. So, i would like your help if possible, about this method of cut bevel gears using complementary angles for gears with sizes out of those rules you offer. Do you know how this process work? How to calculate the best complementary angle? What is the math behind this method? Thank you a lot and have a nice day

@Mewanrahnam575 3 жыл бұрын

Is there any portal that people can donate to your channel?

@prof-rieg 3 жыл бұрын

No, it's all free.

@Mewanrahnam575 3 жыл бұрын

@@prof-rieg your humanity is immeasurable..keep going Sir the world need to learn.

@prof-rieg 3 жыл бұрын

@@Mewanrahnam575 Thank you very much!

@chauvinemmons Жыл бұрын

Going from zero to plus five and then to zero and finally minus 5 I did not notice you making up for the play in the dividing head is that just me not seeing what you did or please explain.

@prof-rieg Жыл бұрын

The play of the diving head caused no problem.

@g7gx271 2 жыл бұрын

1:52 Can you pls tell me the name of background music?

@prof-rieg 2 жыл бұрын

It is mentioned in the beginning of the video.

@Stefan_Boerjesson Жыл бұрын

Great video but not any easy work for an amateur. Just built and verified a digitally controlled rotating table having a resolution of 2.25 seconds. Cutting gears are waiting. The question is what kind of gears there are....

@prof-rieg Жыл бұрын

Thank you very much and good luck for your bevel gears!

@ysasyysasy3650 Жыл бұрын

Pls cutt spiral bevel gear

@prof-rieg Жыл бұрын

Sorry, this is too difficult for an amateur shop. This needs highly sophisticated gear cutting machines, i.e. American Gleason machines or German Klingelnberg machines.