Bicycle Engine Kit Wiring Tips Troubleshooting

No video

Bicycle Engine Kit Wiring Tips Troubleshooting

Рет қаралды 263,214

Күн бұрын

Bicycle Engine Kit Wiring Tips Troubleshooting. This video demonstrates wiring up the electrical side of your bicycle engine kit. After you have watched this video you simply can't go wrong, this is a step by step guide that will hopefully un-baffle the whole process for you.
Just a quick message to let you know I have started a new KZfaq channel for my other passion “Electronics Repair”. If it’s something you might be interested in, I would be very grateful if you would check out the channel on the link below. I try to post at least 1 video every week so do subscribe if you would like to be notified as soon as they are released. Thank you 🙏
/ @irefab

Пікірлер: 22

@dontiavang558 8 жыл бұрын

Thanks buddy, that was very cleared and concise!

@gasoliniroberto7528 4 жыл бұрын

I've been unbaffled now. Cheers

@RoomGrow 10 жыл бұрын

Cool vid, I can hear your Dog snoring behind you! lol :)

@Talscar1 10 жыл бұрын

If you remake the video, remember that the Kill Switch makes a short circuit so the motor doesn't get a spark. It takes all power from the Magneto and use's it up faster then the CDS that converts into high Voltage to make a spark. My Motor on my bike did not fit and now i have it on and it fits. Their is a bit of confusion with the wires as the book that's about 40 pages does not specify what to do with the 2nd wire of the kill switch. Also the people who printed it did it in black and white with a crappy printer. I found this video helpful at a certain degree.

@luissantos5080 8 жыл бұрын

thank you very much for making this video I was having trouble getting a headache and once I saw your video I was very happy thank you very much

@CAZruns 4 жыл бұрын

This worked for me got engine running thanks

@seagreenspiral 6 жыл бұрын

Exactly what I was looking for! THANKS

@tobydyes 8 жыл бұрын

use it to charge your phone with whitewire

@muhammedsilvera6917 10 жыл бұрын

Thanks I found this very useful...

@allvedieoschannel3103 4 жыл бұрын

Thank you very much for making vedieo.

@machfiver753 Жыл бұрын

My bike had it's wires colored backwards. Which made it a pain in the ass to diagnose that it wasn't the cheapness of the parts at fault. I couldn't find quality anywhere for these bike engines anywhere. Mine has a yellow or weak spark. I've bought two new CDI magneto parts and still get a weak spark. I'm down to replacing the entire wiring setup and will be soldering the wires directly to the parts instead of either using spade terminals or soldering wires to each other at both ends. The white wire is for optional headlight but as is the spark sucks I can only imagine how bad it would be if it was having to share power from a headlight as well.

@chunkysmith6442 6 жыл бұрын

thank you so much for this it really helped

@brinnus 9 жыл бұрын

I disagree that you don't use the white wire, You should connect the white wire to the red wire on the kill switch and the black wire on the kill switch to an earth point on the engine (or frame if your engine is earthed to the frame).

@hebronmosiah1629 6 жыл бұрын

Thank you!

@RoomGrow 10 жыл бұрын

The Grubee SkyHawk kits come with all the proper connections so no need to cut or solder anything!

@mr.hemiroids794 7 жыл бұрын

unfortunately the kit I ordered came with different color wires the engine has its own colors and the CDI unit has its own colors and no instructions.

@BritishTechTV 7 жыл бұрын

Hi Simon, The engine will usually have three wires. 1. White (not used) 2. Black 3. Blue or Green. The CDI will have 2 wires. 1. Black 2. Blue or Green Just connect black to black and blue or green to blue or green. Thats it now just wire your kill switch in as normal.

@robertwebb4075 4 жыл бұрын

I'm tring to figure out what wires to hook up where i just gota new stator/ignition with a blue black and red wire if anyone knows a little help would be appreciated