Torque wrench undersized? No problem. Also works with nuts marked for alignment with a marker.
Пікірлер: 23
@spelunkerd Жыл бұрын
You are correct that the wheel bearing is bolted to the knuckle, but the hub is press fit into the bearing. These days in newer cars you buy the hub and bearing as a set, so you don't realize how easily the two parts can break apart. It is true that after a few months that press fit of the hub into the bearing is so solid on the inner race that it is very difficult to get off. So, the weakest link of the chain fails first, the bearing cage. That bearing cage is made from thin sheet metal! If the axle nut comes off, and the wheel is subjected to the extreme forces of the road, that sheet metal of the bearing cage tears away and the bearing splits into two parts, with bearings flying everywhere and the wheel and hub flying completely off. With old style press fit bearings, we actually do this with a ten pound slide hammer. A handful of good whacks and the bearing explodes into two pieces. The inner piece stays with the hub, and a snap ring holds the outer race in the knuckle. So, that axle nut is a critical element that keeps your wheel on the car!
@theoverengineer Жыл бұрын
Thanks for your input, much appreciate your time and experience!
@MattJonesYT5 жыл бұрын
A much more accurate way is to use the fact that torque is length * force. So there are a few things you can do, weigh yourself and use a breaker bar to stand on it a distance away that gives you the right torque, adjusting for the fact that you'll be putting slightly less weight on it since you'll have a hand free to balance on something. If you stand 1 foot away on the breaker and weigh 180 lbs that's the right torque at 90 degrees. Another would be to use a scale and jack, put the jack on the scale and the end of the breaker on the jack, then jack up until it's the right measurement. If the breaker is 2 feet long and you need 180 ft lbs jack until the scale reads 90 lbs plus the weight of the jack.
@HappyHands.5 жыл бұрын
This only works if the hub or bearing one is replacing is the same thickness as the the original one was at time of install.
@theoverengineer5 жыл бұрын
It`s not about a hub or any bearing. Otherwise, yes, or the new gasket or washer or whatever being sandwiched is thicker than the old, etc.
@Seeker-vo2tz Жыл бұрын
Why don’t you just tighten to 150 then A little more which would be 170 lol
@theendofallthingsisuponus15755 жыл бұрын
A smart way to figure it out if you have no torque bar--tighten it as when you undid the nut remembering the effort that was required and match the crimp--just what i was looking for--excellent. Just takes a little thinking.
@mickeymouse48972 жыл бұрын
Pointless incorrect video ... Hub nuts are 1 time use nut, re-tightening to old stake mark is not back to correct torque figure.
@beecee12353 жыл бұрын
The very best I can say is: " the road to hell is paved with good intentions"..... This is NOT "Over Engineering".
@f4tboy993 жыл бұрын
You cannot rely on this method if you have just changed the wheel bearing.
@theoverengineer3 жыл бұрын
That's right
@desireerogers27744 жыл бұрын
Hub bolt on a 05 pilot wats the specs
@danh30134 жыл бұрын
Use a torque wrench, rent one if you dont own one. dont do this.
@theoverengineer4 жыл бұрын
It's a bush fix, it works on shear bolts. Absolutely agree on grabbing proper tool for accurately pre-loading the wheel bearing.
@brianherr51443 жыл бұрын
This is NOT Turn of the Nut method. Turn of the Nut is a method of tightening 1/3 rotation beyond snug. The method shown is poor practice.
@RustyCas9993 жыл бұрын
That’s not “turn of the nut method” either. The amount to turn the nut is based on the diameter, length, and grade of bolt used. 1/3 turn may be good for “some” applications, but certainly not all situations.