Briggs & Stratton Rebuild: Piston Rings, Head Gasket & Oil Seals

Рет қаралды 1,230

Ай бұрын

Briggs and Stratton full rebuild video. Includes head gasket, piston rings, oil gaskets and crankshaft seal. This is the video for a total rebuild of your worn out Briggs. All items used in job are available below.
OEM Engine Gasket Set: a.co/d/5PlQ6rP
OEM Piston & Rings: amzn.to/3QjmfRD
OEM Piston Rings: amzn.to/4a7p5jP
Breakin Oil: amzn.to/4d57tI1
Ring Compressor: amzn.to/49Tfg8R
Engine Hone Tool: amzn.to/4dbTdwY
Engine Hone Oil: amzn.to/3xUPaFm
Torx Bit Set: amzn.to/3Uf0Ytn
Bolt Assembly Lube: amzn.to/3QdpSbC
Reinzosil Gasket Seal: amzn.to/3UfPRR8
Locktight: amzn.to/4bc4NGr
Briggs Manual: a.co/d/fByNrS4
Pick Tool: amzn.to/44cnOX2
Feeler Gauge: amzn.to/4aMSMYx
Oil Filters: a.co/d/0y9tnax
Piston Ring Install Pliers: amzn.to/3WeDjvY
Gloves: amzn.to/4b9XZsS
Torque Wrench: amzn.to/3Uookhx
Sweet Impact Wrench: amzn.to/3WeVu4i
Engine Assembly Lube: amzn.to/3Uunhgc
Manual Gasket Scraper: amzn.to/3JyNZ0x
Deadbolw Hammer: amzn.to/3QeceoE
Drill Gasket Scrapper Pads: amzn.to/49LzTDG
Wire Brush Kit: amzn.to/3UHkoJ3
Wooden Rings: amzn.to/3Q9xPhS
Oil Drain Upgrade: amzn.to/4aUeE3M
KABAR USMC KNIFE: amzn.to/3whvV8d
Pressure Washer: amzn.to/3Uf4NP7
Mower Mike’s Super Cool Tool Store: www.amazon.com/shop/mowermike
Related Videos:
Leak down Head gasket Test: • Riding Mower Smoking! ...
Cylinder Honing Video: • Cylinder Honing w Flex...
Cylinder Head Cleaning: • Cylinder Head Cleaning...
Piston Cleaning: • Piston Cleaning in Engine
Kawasaki Headgasket Video: • Kawasaki FR691V Head G...
Kohler Headgasket Video: • Kohler Courage Head Ga...
Good Luck,
Mower Mike

Пікірлер: 8

@JFL829 Ай бұрын

We appreciate the video, wasnt able to view in total this time but we will be back to finish

@MowerMike Ай бұрын

Sure thing it is a long one

@Elliottdrpaful Ай бұрын

Great job!

@MowerMike Ай бұрын

Thanks man. Was fun to shoot, very challenging

@tartredarrow 11 күн бұрын

The scotch bright rolocks are removing a little bit of aluminum. You can see it's rolling over the edge. I prefer to use a whetstone after the big chunks are removed, and just rub the gasket off. You actually dont need to get it 100% pretty either. It just need to be flat for the new gasket.

@MowerMike 10 күн бұрын

Those aluminum bits are from the scotchbrite itself. It has metal abrasive in it. Not sure what a whetstone is but sounds good to me.

@tartredarrow 9 күн бұрын

@@MowerMike It's a sharpening stone. It's flat so it wont round over or otherwise damage the case.

@MowerMike 9 күн бұрын

@@tartredarrow That is interesting, thanks for the idea.