Cali Raised Ditch Lights: INSTALLED and WIRED to Switch Panel -Tacoma

Рет қаралды 4,471

Күн бұрын

In this video, we will show you how to install and wire Cali Raised Ditch Lights to a Switch Panel in your Tacoma. We will provide a step-by-step guide that is easy to follow, even if you have no prior experience with electrical work. You will learn how to properly mount the lights, connect the wiring, and integrate them into your switch panel.
Shout out to ‪@CaliRaisedLED‬ for sending a replacement light for the Driver's Side immediately. Top notch customer service!!
*Cali Raised Ditch Light Kit for Tacoma:
amzn.to/3PuV5rn
*Crimping Tool Kit:
amzn.to/3PAU3Kw
*Wire Strippers:
amzn.to/3NrTMH6
Switch Panel Giveaway Video (watch for details):
• Valley Of The Gods Uta...
*this channel may receive a small commission when ordering from certain links. Thank you for your support

Пікірлер: 30

@OverlandPNW Жыл бұрын

Nicely done on this install video! I'm a big fan of ditch lights and use mine all the time.

@AZOverland2017 Жыл бұрын

Thank you

@thesecondhalf5823 Жыл бұрын

Loving this Tacoma! This takes it to another level. What a difference these make.

@AZOverland2017 Жыл бұрын

We have lots more to do 😄

@ebikesandstuff1475 Жыл бұрын

Good to see the connection into the switch panel

@AZOverland2017 Жыл бұрын

I get asked all the time how to do it, so I'm showing it. Thanks for watching

@Grimdegn Жыл бұрын

Tacoma is looking good!

@AZOverland2017 Жыл бұрын

Yeah, it's coming along. We have some pretty big plans for it still

@ramirozamora8117 4 ай бұрын

Thanks for this video Now i think i can connect my ditch lights by myself 🤞

@AZOverland2017 4 ай бұрын

Let me know if you have any questions along the way

@user-dw1kc6cj4i Жыл бұрын

Tacoma is coming along

@AZOverland2017 Жыл бұрын

It is

@benjaminharvey2229 Ай бұрын

Wiring question. When I ran my SP9100 controller, it only had positive outputs. I could run the positive wire from the light to the control box and ground the negative wire from the light on the frame close to where the light was mounted. This negated me having to run pos AND neg wires to the box....only the positive. This box has negative connections for each switch as well. Do I need to run the negative wire to the box or can I just ground it on the frame somewhere? Since ground is ground....should it matter where it's grounded? Only asking because when running items say, from the rear bumper, it's easier only having to route single wires vs multiples.

@speedfreak8200 2 ай бұрын

In my experience, spot beams suck for ditch lights.... flood works best. Side Shooters eliminate the need for ditch lights 🤪

@lokithebelgianmalinois2959 Жыл бұрын

Now I can do night runs!

@AZOverland2017 Жыл бұрын

Soon Loki, soon...

@t.j.mackiewicz8944 4 ай бұрын

Is it possible to use the same switch box you cut off the harness? My switch has 6 modes with 1 button.

@AZOverland2017 4 ай бұрын

I'm not completely sure what you mean, but feel free to email me a link to the lights you want to hook up with a little more information and I will respond back. brothersadventuresllc@gmail.com

@peterbrimhall6481 8 ай бұрын

This is a question I cant seemed to get answered. Is there an preformance advantage to mounting lights at the hood level as apposed to bumper or roof level. Im not knocking it, looks cool, but is there a glare off the hood?

@AZOverland2017 8 ай бұрын

I don't believe there is a clear cut answer as there are variables to consider; what type of environment are you off-roading in mainly? How high is the vehicle? What is your goal with lighting? For our situations, this works very well. It is quick and easy to adjust to due to the brackets and height of the lights, If you adjust outwards and up a bit you are not contending with hood reflection though there is a little.

@jms7585 9 ай бұрын

So how did you know to use the 10 amp fused circuit and not the 5, 20 or 30 circuit? Could you use the 30 amp circuit but fuse it with a 10 amp fuse? Basically, can you use any circuit and fuse according to accessory?

@AZOverland2017 9 ай бұрын

I answered this in a comment you made on the Auxbeam video. i just want to make sure you saw my response. Thanks!

@stephanm.4715 7 ай бұрын

What’s the Amp rating for the lights? Were they 5A each? And pairing them made them 10A? Or were they both 10A?

@AZOverland2017 7 ай бұрын

Good question. I remember them being 4 each but now that I'm looking at the specs The should be like 4.6a total so they could be run on the 5a circuit

@stephanm.4715 7 ай бұрын

@@AZOverland2017 Thanks for the fast response again, so I guess that answers my question, pairing them is still going to be about 5A and not 10A.

@AZOverland2017 7 ай бұрын

@@stephanm.4715 Correct