Can You Get Out A Broken Bolt With Wax!?

Рет қаралды 344,461

5 жыл бұрын

Come along as I try every method known to man to remove a seized fastener in this Ford F-250 cylinder head. Ok maybe not every method but with out fail every time I show a method the comment box fills up with everyone's tried and true methods their MeMaw taught them so I thought what the heck, let's give them ALL a try!
If an SMA Video has helped you out please consider giving using "Patreon" to help support us. The videos take real time to create and pull us away from real work that pays our bills. CLICK HERE: / southmainauto
CHECK OUT OUR "SMA SWAG" STORE! Go on Teespring and get your very own SMA merch!
teespring.com/stores/the-sma-...
If you don't like Patreon feel free to use the "PayPal Me" link: www.paypal.me/SouthMainAuto
The South Main Auto Amazon Store:
www.amazon.com/shop/southmain...
AES Wave Automotive Diagnostic Tools: www.aeswave.com/cart.php?m=af...
Thank you for all the continuing support!
--Eric & Vanessa O.
Feel like sending some swag to SMA because you love the videos but don't know where to send it?
Just ship it here:
South Main Auto Repair
47 S. Main St
PO Box 471
Avoca, NY 14809
Disclaimer:
Due to factors beyond the control of South Main Auto Repair, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. South Main Auto Repair assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. South Main Auto Repair recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of South Main Auto Repair, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained

Пікірлер: 2 800

@justpassnthru 4 жыл бұрын

Finally a car repair channel that shows the frustration and heartache that is part of every mechanics life.

@davebarajas5308 5 жыл бұрын

You know you found a great channel when you actually watch the entire 28 min video of a broken stud removal. I commend you sir, great work.

@Misha-nf3eb 4 жыл бұрын

Tytt

@mikespeck8642 3 жыл бұрын

This was Awesome, exactly how it goes for me. I will say, that the heating the aluminum around the stud and a cool stud with the vibration of the impact gun was the secret to you success.

@motoworks7115 3 жыл бұрын

Whenever I am struggling removing a bolt I try to make sure I am using only 6 point sockets to torque on it. The twelve point wrenches and sockets have more play.

@damianfarnsworth7474 3 жыл бұрын

I can watch him all day because of the commentary he makes throughout the video. LOL I started laughing when you said that though because I was thinking the same thing.

@20tea 3 жыл бұрын

Yeah, it really sucks! Sometimes you're lucky, but other times... I have to make sure my kids aren't around or their ears will burn.

@MatthewCBilyeu 4 жыл бұрын

As a guy who does this stuff in my driveway, it's oddly cathartic to see a pro struggle with the same kind of problem and the same silly solutions. Honestly one of my favorite videos.

@MikeFoxGolf 5 жыл бұрын

Weld a nut to the stud then weld a wrench to the nut then spray with lube then sacrifice 2 chickens while facing the setting sun and chanting “demon stud I expel thee” works every time.

@supersabrosinho 4 жыл бұрын

I like the culminating chant, cleanses this Earth of the desecrating evil of corrosion

@aterack833 3 жыл бұрын

I think the parts past the lube just serve as a way to let the heat soak in and the welded wrench heat to keep the lube flowing

@badcompany964 5 жыл бұрын

Every 20 minute job is one broken bolt away from a 3 day ordeal.

@rjh2459 5 жыл бұрын

True, sad but true.

@kevingallineauii9353 5 жыл бұрын

P much dis.

@brianglade848 4 жыл бұрын

Shit hega babba like a week ober hereba

@richb5478 4 жыл бұрын

So fucking true always take your time

@markgentry6688 4 жыл бұрын

Cut flush. Center punch. Drill with short two ended drill bit. Redrill with bit to tap the hole. Tap the hole. Less time spent. Heat and quench will not work an any exhaust part. My personal experience.

@frazerguest2864 5 жыл бұрын

“If I cry, will you hold me ?” LOL I feel your pain, admire your perseverance and ability not to swear and threaten the truck with setting it on fire.

@marcusambrester 3 жыл бұрын

The power of your emotional vulnerability is what coaxed the broken stud out . . .

@daleburrell6273 2 жыл бұрын

...that's the mark of a real PROFESSIONAL!!!

@Golo1949 2 жыл бұрын

Totally agree, it seems some people cannot speak without swearing.

@svtirefire 4 жыл бұрын

You need to turn the truck upside down so the wax will get into the threads.

@ebeegeebeefofeebee3181 2 жыл бұрын

That's how we do it on my planet.

@daleburrell6273 2 жыл бұрын

...ever heard of: "CAPILLARY ACTION"(?)

@svtirefire 2 жыл бұрын

@@daleburrell6273 ever heard of a "JOKE" (?)

@daleburrell6273 2 жыл бұрын

@@svtirefire ...AREN'T JOKES SUPPOSED TO BE FUNNY?!!

@mountainxxxdew 2 жыл бұрын

@@daleburrell6273 jeez you must be the life of the party

@fifteen8 Жыл бұрын

Great vid. I think it was the heat and the crow coming to your aid. He was commanding the head to submit. My ASE Master Tech uncle always told me "don't let it beat you." Your patience and humor are great to watch.

@RJMaker 5 жыл бұрын

Forget the lubes, sprays, vibration, crows, water, heat, ect... what won in the end was your determination.

@zerofriends5592 5 жыл бұрын

'Persistence pays off' ..an old saying every mechanic grows to respect.

@vollickplaysgames 5 жыл бұрын

i scrolled to say the same thing ! lol good on ya man

@snertlegrubber 5 жыл бұрын

Damn right!

@brianb8401 5 жыл бұрын

i concur

@GettingNervous 5 жыл бұрын

RJ_Make Thats exactly what I think. The rule is "dont give up". The most effective way to get a frozen bolt out is to use a lot of perspiration.

@VWWRENCHIE 5 жыл бұрын

" Call of the Crow" an SMA short film, where our hero, the small town mechanic, overcomes countless obstacles to emerge victorious in the battle of the stud.

@robertskolnick8162 5 жыл бұрын

the real secret is ....ya gotta wait til da crow stops laugh n at ja.... next time walk away and shoot the darn crow.......

@yvetterunkle7583 5 жыл бұрын

vwwrenchie

@parochial2356 5 жыл бұрын

In theaters now. Rated R for brief, strong language.

@erikjohnson2889 4 жыл бұрын

hahahahahahaha brilliant

@jeremymenchaca 4 жыл бұрын

In a world of broken bolts, rusted parts, and broken wires, there is only one man who rises to meet those challenges. His name is Eric O. These are his stories.

@pttanz 4 жыл бұрын

This was like watching a suspense movie bro. lmao

@tacman1845 4 жыл бұрын

What I have had luck with is welding a nut, heating the cylinder head, and then using an air duster upside down to freeze the bolt. Expansion and contraction science at its finest. Doesn't always work, but that goes for any method.

@cdshawn 5 жыл бұрын

Last place in the world I thought I'd hear a "deeez nuts" joke!!

@diamondperformancefab5931 5 жыл бұрын

@South Main Auto Repair As a former ford dealership technician I can tell you that the best way to remove a broken stud on a ford modular cylinder head is with a welder. You were not getting enough penetration on your first attempts due to a dirty stud and a poor ground. Here is the procedure I followed that worked for me every time and helped me run circles around other techs performing the same job. Disconnect negative battery cable Cut the stud down until only 1/16" or less protrudes from the head. Clean the stud surface with a wire brush in your die grinder. Clamp a new 3/8" nut in some vise grips so that the nut can be held flush to the cylinder head. Attach the ground to the vise grips. ***If you attach the ground to the engine block you will likely get a poor connection due to oxidization in between the stud and the threaded hole. Set your MIG welder as if you were welding 1/4" plate and weld the nut to the stud, making sure to keep the angle of the mig gun parallel with the stud. The weld should be as hot as possible without distorting the hex of the nut. Immediately after welding, slowly remove the nut/stud with a 3/8" impact on the low setting. If the nut/stud is allowed to cool before trying, it will be harder to remove. After one truck with 6 broken studs you will be a master at this process and it will take less than 5 min per stud guaranteed!!! A tip to aid in the removal of the nuts on unbroken studs, park the truck in the sun and let it idle for 20 min to thoroughly heat soak the engine, and remove the manifold nuts while the engine is hot.

@elguapo1690 4 жыл бұрын

Why cut the stud down so far?

@tacman1845 4 жыл бұрын

@@elguapo1690 longer studs are more likely to twist and break.

@briankidwell232 4 жыл бұрын

Warm engine they come out everytime

@jackschitt7783 4 жыл бұрын

"You were not getting enough penetration on your first attempts due to a dirty stud and a poor ground." This had absolutely nothing to do with electricity. And welding a nut to a broken bolt doesn't always work 100% of the time. It does work most of the time but not all of the time. Doing it this way can sheer the bolt off flush with the surface of whatever it's in.

@mikeberry304 4 жыл бұрын

Good advise is always welcome as long as it's not from the guy in the pub , because he knows nowt , great tip !!!

@tiztiz5839 4 жыл бұрын

This is the videos that nobody wants to show, but you show us what really is to be the best tech on youtube

@davidr9408 4 жыл бұрын

My goodness you had me laughing so hard! "If I cry would you hold me" 😂😂

@spelunkerd 5 жыл бұрын

Thanks for keeping the camera rolling, I would have been throwing things. You were cool as ice cream, ha ha.

@SouthMainAuto 5 жыл бұрын

Did you get your package yet?

@spelunkerd 5 жыл бұрын

Mail moves slow up here in the cold north. I'll let you know, thanks for the heads-up! There's another Canadian mail strike coming, it could take a while.

@davidstuck2866 5 жыл бұрын

glad you finally got it out. i am now retired but spent my life as a motorcycle mechanic. i had an exhaust stud that was seized in aluminum so bad, i did everything all of us at the shop could think of. with no luck at all. to get it out, i ended up drilling along side of the stud into the threads, and use multiple applications of muriatic acid which ate enough of the material away that the stud finally broke free enough to extract it. its funny how determined we can get when we have to.

@Michael-mz6uf 10 ай бұрын

I can’t believe I watched this man for 30m try multiple different ways to get a bolt out. And yes I learned a lot.

@pachioue 4 жыл бұрын

"So, that was pretty easy..." The way you said that made me laugh so hard I almost toppled over with my chair! Thank you for taking the time to make these videos, and I hope all is well in the world of SMA!

@alcamus1068 5 жыл бұрын

Way to hang in there! No flying tools or fbombs! ! Great vid man.

@jimmygarlon750 5 жыл бұрын

This is better than Days of our lives

@scottellis7618 3 жыл бұрын

I know this video has long since passed but I think it was the patience and persistence of the professional mechanic beautiful job nice hanging in there

@laurijorgenson6683 Жыл бұрын

Eric, You often have me laughing out loud with your comical comments along with teaching me. You are entertaining and useful on so many levels. Thanks so much for all of it.

@felixpetrowski1286 5 жыл бұрын

Walking away..... but you have to walk back.....that's persistence!!!! Remember, a Master has failed more times than a beginner has ever tried!!!

@repro7780 5 жыл бұрын

Do, or do not. There is no try - Yoda

@ericsandrin8123 Жыл бұрын

thats how you become a master..a whole collection of failures and stubborn persistence till it works...

@imafarmboy2 4 жыл бұрын

It was the Facebook prayer request. You got some pull, Son.

@danielalamo2075 3 жыл бұрын

It was all of the above. And the call of crow stopped because death came to the evil bonds that held in the bolt. And thank you for showing and sharing your FRUSTRATION! It seemed like I'm the only one getting the "swami stumper " problems. I have used all the methods you used along with lots of cussing and throwing things. And walking away. But I'm only working on my own stuff on my little ranch. I love your channel. You always show real problems and real outcomes. And thanks again.

@ricktipton9563 3 жыл бұрын

I can enjoy watching this guy being cool when faced with frustrating crap. By the time I'm onto plan C, I've yelled plan F this S several times. Keep the good videos with good attitude coming Sir.

@doug12382 5 жыл бұрын

2 video's in one day making my day

@ColdWarVet607 5 жыл бұрын

Mrs. O did it by being there...."It was beauty that killed the beast".

@johnnhoj854 4 жыл бұрын

"Some say he is still there, welding nuts to the bolt, only to break them off again."

@GatheringSticks 4 жыл бұрын

i seen people have success by welding a washer on then a nut.

@philbg6378 3 жыл бұрын

Perseverance did it my friend! Good job.

@mattijur4374 3 жыл бұрын

Perseverance was the key. And I wish there would be a sequel: removing the three stuck bolts from the other side.

@tomthumb1941 5 жыл бұрын

I watched the video, my conclusion was the heating and being persistent was what made it happen, also walking away for a while works many times when you go back to it. great video. Tom.W.

@bartscave 5 жыл бұрын

I'm more of a welder than a tech, but I have done a ton of broken bolts. I have some posts on IATN about it. The trick, even for recessed bolts in aluminum is still welding, just a little different. For your 8MM stud example I would take a big black iron nut, say 1/2"-5/8" or so. Hold it over the stud and place your mig wire in the middle of the hole. Fire it up, concentrating the heat in the center on the stud, then slowly filling the hole in the nut. let it cool and back it out. It may not work the first or second time, but each time the stud heats in its ridged hole it shrinks a little. It will come out. I have done this on recessed bolts in aluminum as well. Tip: ground close to weld, you don't want welding current traveling through valves or electronics.

@wyatthull6613 5 жыл бұрын

Bart Young I worked a Chrysler dealer and a Chevy dealer as a body man. I’ve successfully removed over 100 of these bolts using the technique you describe. Never had one give a problem. And the worst part is never got paid for the repairs because I wasn’t a ‘certified tech’. Just happened to be the only guy in the shop that knew how to weld.

@leupold4089 5 жыл бұрын

Bart Young, I also I'am a welder in fab shop for 30 yrs. you are correct he wasn't getting enough penetration on the bolt. weld laying on top ,I would grind tip of bolt to a taper and weld around, but in a close spot like that a over size nut great idea in any situation .

@signlsirchir2156 5 жыл бұрын

Used this method yesterday on a pos 3400 v6 exhaust manifold stud. 13 nuts later I finally got one to stick.

@JP-kk5vw 5 жыл бұрын

@@wyatthull6613 I would demand payment from who ever is in charge for the repair! Let the certified hack do it then. Never give away your skills at a job. Furthermore, if the certified hack did not compensate you with something, ballgame tickets, tools, hooking you up with a chick Etc. Then it's a one time show for that guy!

@randy1ization 5 жыл бұрын

ALSO always disconnect both battery cables when welding on a car

@brentfrancis9187 4 жыл бұрын

If this was me doing the video there would have been about 25 minutes of: BEEEEEEEEEEEP ending with: Henry Ford.

@prestoc3034 4 жыл бұрын

The crow is a very special bird that gives you insight when it knows that you need it. They intuitively understand what is going on around them, and are able to get our attention through sense of intuition while verbally getting our ears up. Crows will stay around and live close to a person that they love, for a very long time. I made this discovery about 6 years ago, and the crow that made it's debut in my life, is always around and has been for the whole six years, and she still helps me to realize things when I need to. Your crow, was helping you to realize that you needed to take a breather and think for a sec, and it worked. You realized her potential to you, and that is the reason why she is in your life.

@ateamfan42 5 жыл бұрын

"Something that should take 30 seconds turned into a 3 day ordeal." So, like, every project I attempt then?

@REDMAN298 4 жыл бұрын

I put off replacing my kitchen faucet for a year. Figured everything was gonna go wrong. Finally did it this week without a snag. Even re-used the line and compression fitting for the dishwasher. I keep looking for leaks and really appreciate that it`s all good.

@kylewellsby2176 3 жыл бұрын

R D every thing I do it’s always 10 times longer than the average person😂

@williamcollins4082 3 жыл бұрын

And not just wrenching ether !!! Fixing other people's screw ups !!!

@UOttawaScotty 3 жыл бұрын

I have to do this exact this on my motorhome this week, only I suck at welding and have a shit welder, so watching you, I don't like my chances here

@ogbobbye 5 жыл бұрын

that was 26 minutes and 51 seconds of reliving every broken off rusted in can't get nothing on it cause you can't get to it but it has to come out bolt I've ever come across in my life and in the end the walk away is what always worked.

@dg-fx5qt 5 жыл бұрын

I would have used brake fluid better than penetrating oil

@oldschool1993 4 жыл бұрын

Next time use a larger nut- like a 1/2 size so you can weld around to outer edge of the stud as well as the top- you will get a lot more strength that way.

@ryansteve8739 4 жыл бұрын

I think what made the difference was the last time you welded the nut on the stud the nut was further down allowing you to get more surface to weld on versus the other times you were only welding on the top of the stud. The last time you were able to weld a little on the sides of the stud. So I think that helped and made it a lot stronger. Some people say first weld a flat washer to the stud and then weld a nut over it. It allows for more purchase. Just my opinion.

@williamduncan5679 11 ай бұрын

I think once you welded the nut on the bolt let it cool down then heat the body around the stud through the ports both sides of the stud without heating the stud,simple Eric deary me.😂😂😂

@justaguy427 5 жыл бұрын

Dude you're funny as hell when you fight stuff like this.. I say an angry mechanic is one of the best comedians you'll ever hear.

@tabithafrance8844 4 жыл бұрын

Trick is to use a bigger nut and fill in the gap around the stud. Cold start on those machines getcha every time with a nut that size.

@BigDaddy_MRI 5 жыл бұрын

“Endeavor to Persevere.” - Chief Dan George from “The Outlaw Josie Wales”.

@patharmon9760 3 жыл бұрын

THANK YOU SO MUCH!!! I've been saying they smell like crayons for as long as I've worked on cars, and no one knows what I'm talking about.

@super20dan 5 жыл бұрын

this is why I switched to cutting grass for a living

@IamDerick 5 жыл бұрын

I have done it many times, they have never just fallen out after the treatment. I would say it is about 75 percent effective over my many years of doing it. Heat-treat-cool 3 or 4 times is my preferred method. Cool vid! And yes my VW interior smells like a crayon. ;)

@skippyglen6610 5 жыл бұрын

I tell what got that stud out was an absolute refusal to be beaten. Been there myself and was willing that stud out with you. What a feeling though when they start moving. All the best and love the channel.

@kenr.4526 3 жыл бұрын

Back in the day while working for a famous name muffler shop, we did a lot of VW Beetle mufflers. The attached directly to flanges that were cast into the aluminum heads secured usually by steel studs. The studs were typically rusted down to the thickness of pencil leads. The usual solution was to leave the nut alone, rusted to the stud, and heat the ears of the flange part of the head only. This made the flange expand and release the stud enough to where you could back the whole stud out with a socket/swivel/extension/ratchet. You had to work quickly and as soon as you felt it starting to bind up, stop and add a bit more heat and then repeat the process. I still have a few that I removed as "trophies" that always made people say "NO WAY !". Usually replaced the studs and nuts with stainless. This was why it took about 2 1/2 hrs to do a VW muffler held on by 4 nuts ! It worked about 90% of the time.

@jeffclark5024 4 жыл бұрын

I’ve had good luck with the nut welding technique. I don’t cool it tho. Give it 1 min to cool then use hand tools and slowly work it back and fourth while still warm. Like you, I’ve also had to do it multiple times. Usually that slow careful back and fourth tears the aluminum in the first couple threads or two until it comes free. Good work! It’s not a job for the faint of heart.

@jackmeholf5901 5 жыл бұрын

Just recently had a 5.4 l manifold job. Broke 5 studs off tried welding nuts on they just kept breaking on each one .. tried welding an 8 mm washer on first then weld a nut to the washer every one of them came out on first try.

@dopodownsu 5 жыл бұрын

This. The washer allows your weld much more real estate to hold onto the stud.

@gonesideways6621 4 жыл бұрын

Ideal weld would be front and back of nut since this is not possible washer is next best option.

@golfish8589 4 жыл бұрын

There is a newer message than yours written by a Ford mechanic talking about how you should grind the welder to the nut for a better weld

@vodonnell1 5 жыл бұрын

Got to admire your persistence, good job.

@garymcmullin2292 2 жыл бұрын

this is a late comment but my hat is off to you! THAT was a testimony of a true professional mechanic. I have watched all kinds of videos about broken bolt removal and they all claimed the welded nut would not fail. I have had some tough ones during wrench turning since 1965 and I know broken/seized fasteners are not always a neat and clean fix. This one took the prize. Sometimes I get to wondering if after the heat there needs to be a total cool down, metal expansion/contraction is the mechanism when relying on heat. Maybe even a spray down with refrigerant to cryo freeze the fastener. I feel for you guys in the rust belt, repair cost rates should reflect these wars.

@aoksys31 4 жыл бұрын

I've used an old syringe with a long slender needle to inject penetrating oil or other lubes into otherwise inaccessible spaces. You might be surprised to find that there is almost always a tiny crevice or hole available to let in the penetrating fluid. It's a lot neater than spraying all that stuff all over your work area hoping to get a few molecules of oil into the threads.

@davidbrown1037 5 жыл бұрын

My "GO-TO" method is to weld a nut on with a TIG Torch. That system uses an electric ARC from a Tungstin Electrode in Argon Gas to shield the air from the molten puddle. The amperage is controlled by a foot peddle and you can hold the arc at low amperage on the stud without adding filler metal. Heat the stud and allow the heat to soak deep into the threads to expand the stud and break the corrosion structure up a little. Finally add 309 Stainless Filler Rod to weld the nut on. Spray with penetrant & follow the procedures that you did. TIG and 309 Filler material is usually a much stronger weld than MIG in such a small area. You can also reach down to a stud below the surface, heat it up, and add rod and build it up to above the surface, then weld a nut on, without affecting the hole and threads. The precise control of the TIG process makes this possible with some practice, but it takes some specialized equipment. Anyone with TIG equipment should try it. I once removed 7 broken studs from a Chrysler Slant 6 in about 40 Minuets. I have also removed a few hundred broken 5/16" Exhaust Studs form Aluminum Aircraft Cylinder Heads that are set in HELICOILS at the factory when new. And yes.... I was on the edge of my seat.... having been there may times.

@jpack61108 5 жыл бұрын

Wont be long until you hit 200K.. This channel has grown like wild fire over the past couple years.

@MrSpartanicus 3 жыл бұрын

I guarantee no one minds if the video “has gone stupid”, the commentary is hittin home, brother!

@TomCooperBHG 4 жыл бұрын

Mad props, sir. Thanks for the PG channel and for helping this layman feel a TON better about the trials of stuck bolts!

@DaneSaysStuff 5 жыл бұрын

The thing I learned with welding a nut on, is to let it cool completely before touching it. I went thru the same battle as you on a GM 5.3 and what won in the end was weld the nut on, then go do something else till its cooled off. Every time I tried it hot, the weld broke.

@loopy4517 5 жыл бұрын

I agree. Letting the nut cool is very important on something like this, especially with the size of the bolt you were trying to remove. Eric, your videos make me feel like I'm back at work with the guys. I wish your videos were around 15 years ago when I was still working on my cars myself. Keep up the great work.

@SmittySmithsonite 5 жыл бұрын

It's not the beat, the heat, the quench, the wrench .... nor is is the crayon .... it's the TENACITY.😁 I've got a little of that too. At the expense of my health, I'll keep at something until it submits, one way or the other! Swearing furiously at the top of my lungs, and throwing tools in every direction seems to help too. 😜 Nice work! Now I dub you, TENACIOUS EEEEEE. 🙌 👍👍😎🤘🤘

@SouthMainAuto 5 жыл бұрын

I honestly think it was all the mother effer's when the camera was off haha

@SmittySmithsonite 5 жыл бұрын

That gets 'em every time! 😁

@MrGamerholic 5 жыл бұрын

@@SmittySmithsonite amen to the original comment. I can't tell you how many times if done that exact thing. Had a starter bolt on an 85 mustang v8 (lower bolt faces the front of the car and you can only get to it with 2 feet of extensions), would not come out for almost 6 hours lol. I cursed up a storm on that one.

@SmittySmithsonite 5 жыл бұрын

Yeah, I don't know how anyone can work on anything built after 1995 for 3 minutes without cursing the engineers who designed it. By minute 7, I'm throwing stuff, LOL. 😂

@scroatworx2339 5 жыл бұрын

smitty, lol my ass off! I hear ya brother, i'm the same!

@elwhastrummer 2 жыл бұрын

"That was pretty easy".... LOLOLOLOLOLOL.!!!! YOU'RE AMAZING ERIC

@glenpiles1775 4 жыл бұрын

My name is Glen P I am a retired maintenance machinist and toolmaker (46 years) .Its been my experience That when you have a portion of the broken bolt sticking out and try to weld a nut on it mig weld is not the strongest weld to use. I have done it with 7018 stick rod with good results but the best has always been with 6011. 6011 is a high nitergen rod used for a root pass because it gets deeper penatration.it will amaze you how much stronger it is.Sorry for bad spelling I made my living with numbers not letters. I worked in a plant with 200 hundred and was considered the best toolmaker welder in the plant

@bradjohnson6919 5 жыл бұрын

You used the wrong color crayon. The green ones work every time. :-)

@deucerider430 3 жыл бұрын

But only on the driver's side! You need those yellow ones for the passenger side!

@joeltoporski655 5 жыл бұрын

You live a charmed life, never in 30+ years of doing this in Michigan did one come out that was stuck that hard

@softwareengineer9217 3 жыл бұрын

I got a face. That only a mother can love. 🤣🤣🤣🤣 this guy's a good tech and a very good comedian too

@mikemcdivitt7216 3 жыл бұрын

When watching a 28 minute video on removing a frozen bolt holds my rapt attention the entire time....And the Emmy goes to...SMAR LLC.

@davidtimmel4027 4 жыл бұрын

I admire your patience and determination not to let that bolt lick you. Who can say which method worked? I think the heat and air hammer is best. The crayon, water, or krill oil never got near the threads. Great vids, educational and entertaining. Stay with it partner, we're with you!

@carltona6429 5 жыл бұрын

Patience is what did the trick.. patience and persistence.. another great video

@SteveP-vm1uc 5 жыл бұрын

I think Mrs.O kept him in shape.. lol.... YEAH, MRS. O!!!!!!

@dave27889 Жыл бұрын

The crayon and hammer wrench set not giving up!!! You don't give up!!!

@damienirvin777 4 жыл бұрын

I bought a $16 stud removal tool from advance auto that work to pull the broken, rusty, seized up studs out of my 4.7 head. One of the best purchases I ever made. Attaches right to an impact and tightens up as you go. Never failed me.

@molliarti 5 жыл бұрын

Perseverance,persistance,patience its the key,but... but... The process for yourself its crazy. Desesperation,anxiety,a lot of time,crashed hands,explode brain,etc haahaaha But... but... In final,when goods all,the peace and satisfaction its wonderful. Super nice job bro,clean clean!

@tiredoldmechanic1791 5 жыл бұрын

I've used all of your methods over the years except the wax. I've welded to the stud before adding a nut so I could use a bigger nut. The oblong stud allows for penetration along side the stud. I used 11018 welding rod. Once the nut is welded on, heat it with a torch to keep it hot for a few minutes then slowly back the torch away to let it cool slowly. This anneals the metal so it isn't as hard and brittle. Do the same to soften the metal if you have to drill the stud. I've used liquid nitrogen to super cool the broken bolt.

@jonhaskell9630 3 жыл бұрын

My "last resort" trick is to clean the bolt with a die grinder, etc and then grab a fender washer that closely fits the bolt. Drill a smaller one if necessary. Grab like a 3/4 nut and tack it to the washer to hold it. (button magnets will hold it in place, but they DIE as soon as the welder heat nails them). Put the welder on the highest power, and slow the wire feed... which puts more heat to it. Using the oversized nut allows you to weld in around the threaded portion of the bolt (instead of just the broken end). After you've filled the nut with weld (circular motion), quench it with a sopping wet shop rag till it stops steaming. THEN hit it with the tiger piss, kroil, blue crayon, or the special sauce from McDonald's, before it completely cools. Let it cool off completely before trying anything. I like the air hammer idea... Never tried that. Maybe it's worth leaving an indent in the nut, rather than welding it "full", so the tool can set in there. Nice video as always!

@jeffhanson3675 4 жыл бұрын

I got a 98 f150 cheap and it was a landscapers truck. They also did snow removal and salting. The exhaust bolts were so bad we just pulled the engine out to work on it. Easier to check on other thing too while it was out. This rust bucked has been the bane of my existence. Your videos have given me the confidence to tackle these jobs. So far I've removed and reinstalled the engine, exhaust manifolds, both cats and full dual exhaust. Full rear drum kit, full front caliper kit and all new stainless fuel lines and brake hoses. She should just about be good enough to pass inspection. Damn Long Island winters tear vehicles up man. Love the videos.

@miguelfatman6066 5 жыл бұрын

Hey Mr. "O", your patience knows no bounds but I am also darn sure you used the wrong colour crayon.

@qualityrenov 5 жыл бұрын

one of the best most intriguing episodes you have posted, Sir. good job, as usual

@jimwilson9005 2 жыл бұрын

Your tenacity is what got the bolt

@dougthomasmusic Жыл бұрын

Well said Dave. This guy is working on the stuff no one else wants to do. It looks like he’s in the north where weather reek havoc on all things metal. Make being a mechanic in the south look like child’s play. Thank you for giving me more confidence to do attempt tuffer jobs. Maybe I can thank you by giving you a guitar lesson or two. Watch now, Mr O is probably a rock star on the guitar 🎸 as well. 😅

@mongomay1 5 жыл бұрын

From the AL/FE electrolysis (white powder in the threads) the heat, quenching and mechanical vibration were positives in removing the broken bolt/stud. What I still do not understand is that there are some very high temp anti-seize products out there that are not being used. I use to use pool o-ring lube silicon grease or silicone vacuum pump grease, when I was fastening bolts into Aluminum to prevent that electrical connection and fill the air gaps on the threads to remove the amount of space electrolysis could occur. The navy learned the hard way back in the 80's with aluminum superstructures on top of a steel ship and salt water to try and save weight for new fuel economy standards on new ships being built. Have the same thing going on in Upstate N.Y, just on the highways. Wait until folks need body work on the new ford trucks....

@ronplucksstrings7112 4 жыл бұрын

You are absolutely right!...the white powder on the threads was aluminum oxide, preferencial to iron oxide because of alu's place in the galvanic series..it locks the things together better than welding! Like I always say...you can't stop mother nature! ...but you can slow her WAAAY down! by using graphite or zinc filled anti-seize greases when assembling....but why should any manufacturer? When the bolts are new, at the factory they don't have any problem...more planned obsolescence by those pricks ...if there was an option where you could pay an extra $100 when you bought a new car, to have it fully assembled with anti-seize, I would! Anybody who assembles something where alu is in contact with iron, like bolts in alu or bolts through an alu bushing, and doesn't use anti-seize, should be slapped about the head and shoulders...MANY times. That is all!

@tsakaln1 3 жыл бұрын

@@ronplucksstrings7112 Great points! Can you suggest some products that we can buy at NAPA or some other retail shop to use for engines (high heat) or other applications? Much appreciated!

@ronplucksstrings7112 3 жыл бұрын

@@tsakaln1 For high heat, you can't beat a graphite/nickel filled anti-seize, because although greases will cook away, you'll never cook away graphite or the other particulates!...yes I said NEVER! Permatec/Loctite Anti-Seize is one of my favorite products (no relation!)! Use is on just about anything with threads, including hot, like exhaust manifolds and headbolts! (When using it where fastening torques are specified, like headbolts, adjust specified torques down by 10-15% because of the "K-Factor"). Cheers

@tsakaln1 3 жыл бұрын

@@ronplucksstrings7112 Thanks for the tips and quick reply!

@kevinhancock4064 2 жыл бұрын

@@ronplucksstrings7112 I second that why can't these firms use anti sieze or whichever suitable I've currently got 5 header bolts to sort it's a headache but love the video persistence paid off

@kellyspeppers 5 жыл бұрын

Did you use Ford blue crayola?

@johnrschmidt2 5 жыл бұрын

Those can only be used on a Toyota Crayola.....

@timbower9413 Жыл бұрын

Great video. First one I've seen that documents the process warts and all. Stuff goes wrong. When it does, go to plan B. Still going wrong? Go to plans C-G. That was way more helpful than watching someone remove a broken bolt that was set up for video brevity. Now I know not to get discouraged when I twist off the first weld without budging the bolt. Thanks for the vid!

@mikechimko8564 4 жыл бұрын

That ladies and gentleman is the definition of patience and perseverance. Both qualities necessary to become a top level auto mechanic/technician. I think this is one of the most demanding trades, if you have a reliable guy that you deal with and he gives you a fair shake-treat him like gold.

@TheWoodman064 4 жыл бұрын

I was greatly rooting for you from the very beginning! And so you know, and I have only told one other person this, my dad! You are beyond and an incredible, persevering and determined mechanic. You are, the master of mechanic masters oh great one! Lol! Awsome job! I am so enjoying watching you work!

@DD-DD-DD 5 жыл бұрын

I, for one, appreciate your contributions to the scienmatific process of bolt removal technique testing.

@leecarroll1817 Жыл бұрын

Lest I forget I enjoy your stuff and you possess the Patience of Job.

@smash5967 Жыл бұрын

So I know this is old, so you might not see this, but as a welder, I think the walking away is what did it. Quenching the weld makes it hard and brittle, and leads to breaking. Heating and quenching might break things loose, but if you're worried about it snapping, following that up with a heating cycle and letting it cool as slowly as possible will really help with weld (and bolt) toughness.

@claytoncoolidge992 3 жыл бұрын

As odd as it sounds I've had really good luck with soldering flux. I like to apply some before I heat it then after heating i just keep slathering it on till its too cool to melt any more. One good thing about this method is once I go to weld a nut on I heat the bolt one last time and melt the flux off and its pretty clean to weld to. Weld a washer to the bolt first and use a nut thats bigger than the bolt would use this allows for some penetration below the top of the nut and make sure to weld it to the washer as well. I never allow it to cool too much after I weld and try to use the more directed heat than the torch provides as welding tends not to warm up the other surface as much

@crumplezone1 5 жыл бұрын

Love the way he used the two versions of Aloominum and Aluminium to keep us Brits and you Yanks happy :)

@DaKineGuy 2 жыл бұрын

This is one of the happiest endings to any video I've watched ever

@doublebuckshot1612 3 жыл бұрын

Considering that bolt wasn't broken flush I think I would have placed a thin washer on the bolt against the manifold, after that I probably would have used a larger nut to properly penetrate the bolt from all sides and edges. I'm happy to see it wasn't easy considering the entertainment we all got. The struggle was real and like others stated you kept focused, didn't get a temper, and succeeded.great video keep them coming.

@farmcentralohio 3 жыл бұрын

And another that missed the point of the video

@kellyokamoto1604 5 жыл бұрын

Is it just me or does this ALWAYS happen to the bolt that's LEAST accessible???

@exidy2290 5 жыл бұрын

Murphy's law, it's always the least accessible.

@poppy1007 5 жыл бұрын

+Exidy Murphy's Law states that anything that can go wrong, will go wrong. I like O,tools law, that states that Murphy was an optimist

@Prosecute-fauci 5 жыл бұрын

This bolt was extremely accessible

@robertscott245 5 жыл бұрын

Yep it's called Murphy's Law.

@randyeastman4500 5 жыл бұрын

nope not just you all but one comes out always gotta be one

@frugalprepper 5 жыл бұрын

Well Duh you have to use gravity to pull the melted crayon down into the threads. You have to flip the truck up over on its side first.

@chrishernandez2490 5 жыл бұрын

No, you have to remove the engine, and reinstall it upside down. Then use the crayon

@fyshlearnstoskate 5 жыл бұрын

Obviously this only works in Australia

@rickh6963 5 жыл бұрын

You three need professional help..... I was laughing hard!!

@kweidnernc 5 жыл бұрын

You used the wrong color crayon.

@frugalprepper 5 жыл бұрын

@@kweidnernc Right you are supposed to use a clear one.

@pauliebots 2 жыл бұрын

It's amazing how many times those stuck bolts release when the temperature seems to equal. This was a lesson in patience...well done sir.

@sobconners 2 жыл бұрын

It's because they cool at different rates less than from the heat that's applied.

@shopart1488 4 жыл бұрын

I broke the bolt drilled it out into the water jacket then replaced the head on fords V10. I would say you did very well. Of course Mrs.O can’t be forgotten for her efforts!!!👍

@maxw576 5 жыл бұрын

Gee Eric - Everyone knows blue crayons lock the threads. Thank goodness you didn't use red!

@SouthMainAuto 5 жыл бұрын

Yellow next time?

@ethanpoole3443 5 жыл бұрын

South Main Auto Repair I thought green was the penetrating color? :-)

@trainer2018 5 жыл бұрын

I have used all the methods minus a candle or crayon. No offense Eric but this video made me feel better,lol. I'm not the only one who struggles with repairs like this. Once I was trying to get a half inch diameter radius rod bolt out that was broken and it took forever,lol. I had the frame so cherry red around the bolt to get it out that you could cook hot dogs on it. So after hours of soaking it with wd40 and then trying the quench method it finally came out. Every time something happens like this at my job I jokingly say to everyone Anti Seize is your best friend.😉

@consaka1 5 жыл бұрын

Amen to that. I anti-seize just about everything that goes into anything hot or aluminum.

@rchick9682 5 жыл бұрын

busjockey1 I

@randymiller1604 3 жыл бұрын

I am a retired boat motor mechanic removed 1 million broken bolt don’t hit theBolt heat around the Bolt and remove it quickly it works usually good luck God bless

@EATSLEEPFARM 3 жыл бұрын

Quick tip for anyone one dealing with this that has a welder. Get you a washer that’s the same size as the bolt ex: 1/2 bolt grab a 1/2 washer or even the next size up and weld it to the broken bolt. Even works great for bolts broke flush. Once you have it welded get a nut that has the same inner diameter as the whole washer or atleast close. The object is you have a lot more area to weld to and a better chance of getting good penetration. Have never not had a broken bolt come out by doing this. Just thought I’d share

@todddiedrich9106 3 жыл бұрын

I stumbled on you channel can’t stop watching it. It’s good to see a mechanic that just likes to fix things correctly and honest. I’m a mechanic as well been doing it a long time like to see if there’s another trick for problems always learning

@gotspeed1212 5 жыл бұрын

I've had luck welding nuts on but the trick is run a carbide burr around inside the nut to clean up the stud so the weld is nice and clean and turn the heat all the way up on the welder. Also a can of compressed air upside down so it shoots the freezing chemical in it and freeze the stud after the heat has soaked in to the head. The head won't soak the cold from the stud but you can get the stud to freeze the length of the stud.

@oh8wingman 5 жыл бұрын

Sometimes using a larger nut will help especially if there is some stud sticking out like it was here. If the stud is long enough to actually protrude through the nut you can now get a fillet weld around the stud which will be stronger than the plug weld you got here. If the stud does not project out as far as this one did a larger nut will allow you to get a better weld on it simply because there is more room. If it is broken off flush, weld a flat washer to the stud and then a nut to the flat washer. I've used all three methods over the years with relative success. Always let it cool to the point of touch before trying to twist it out.

@scflooring8658 3 жыл бұрын

That mema is one smart lady she has taught you well! Great video love videos like this keep them coming!! Like they say patients is a virtue and you sir have more patients then anyone I’ve ever seen and not swearing too wow I would have said a few choice words on that bolt!! You the man Dr. O