Your videos really are good. It's so easy to understand what you are explaining and all done effortlessly in a very concise and timely manner. You have a gift teaching.

Excellent informative video. Please do more videos, you deserve a bigger viewing audience.

Amazing information about yourself

Thanks a lot, lighting could have been more for clearer video details and it's great u also showed us how to clearly fit back the removed valve body nd etc

Thanks for your help and support

Can you help me where is the input shaft speed sensor located?thank you

Great video, thank you for all the good content, job well done. Would it be a good idea to change input speed sensor since this is some what labor and time consuming? If so is the input sensor located at the bottom of the trans?

All those wires and connectors are in the ATF? So it's not conductive? Interesting!

hi bro my vehicle has a problem when i put the vehicle in the drive mode it will run normal for a small distance and after that its rpm will comes to 2 and it will not increase and slow moving engine warning light also showing ,my vehicle is 2010 model Chevrolet Malibu. please advise the solution.

Great video mate, thankyou.

Hello, I have a Chevrolet Orlando diesel automatic. I have the code p0700 p0717 p0716. The car works, but it does not accelerate more than 40 km, as if it is only in first gear.

¡Great video! Few are this good and clear! Just a question... What is the car malfunction generated by this bad sensor?

Good quality video

Great video thanks! I need to change the range sensor on mine. Anybody knows what needs to be removed to replace the internal range sensor?

Great video! Have u come across fault code P1915 it’s to do with the gear selector switch range not correct on start up. Puts the transmission into limp mode. Not much info on the switch replacement. Thanks Matt

Excellent 👍

Thank you very much for the video, one question is there a need to remove all the oil from the transmission box to change the sensor? thanks.

I have a 2012 Chevy Cruz That needs an output sensor are they the same transmission What it be the same thing you did hear

Great video!!

Good job

I got a 2008 malibu that needs the speed sensor replaced...do i have to have a scanner to program it after i install the new sensor?

Any clue why the car itself wouldn't move at all ?

What where initial symptoms I have one no engine light jus won't rev past 3000 rpm when in park or netural

I have to do an output speed sensor on a 2012 Chevy Cruz would it be the same job as the 2011

Hola Tengo un cruze 2010 automático, le cambié el sensor de velocidad pero luego el velocímetro no hace nada y en D no pasa las marchas, si me puedes orientar con este problema te lo agradecería ya que tampoco se prende el testigo check

I have same code with many other codes .is it normal? I have p0700.p0752.p0777.p0797.valve 1.2.3 stuck on valve 5 stuck off

Hi mate.thanks for video.my 2010 Holden cruze sets p2417 which related to pressure sensor stuck. Thinking to remove TCM and replace sensors . what you reckon?Have you done this before? Any idea where to buy sensors? CHEERS

Im working on a 2008 malibu LTZ with 3.6L if that matters. I forgot to mention that.

Hello. I have 2010 cruze. Trans Overheating due to thermostat (stick in half (not open -not close) ). Outspeed sensor is no signal only when i go far (40 miles) . So turn off the car, waiting 1min and everything is ok. Changing it may solve problems ?

Hey bro awesome vid man. I have a 2013 holden cruze 1.6 manual and im have problems with the transmission. When its in neutral its as if its in 4th gear and it moves but when you shift to 1st it goes into like 5th. Just not selecting gears properly. Any ideas?

Is the input in the same location?

Is this the same as a 2014 chevy sonic 1.4L auto?

I purchased a 2010 holden cruze 2.0 diesel. Speedo not working. Gears not changing have to manually put in 1/2/3 and reverse to drive. And shifting hard when changing gears. Guessing that's becuase it doesn't know what speed it's going. The permanent codes I am getting are. P0717 input/turbine Speed sensor "A" Circuit no signal. And P0722 output speed sensor No signal. Apparently the output speed sensor was already changed??

Hi mate, thanks for a either Video you made Appreciate can you tell me where can I buy transmission output sensor I have no idea where can I find it?

Hi I have a 2011 Holden Cruze JH manual 5speed, is the speed sensor in the same location as that?

This sensor need programing?

Hi please help my chevrolet cruze 1.8 engine automatic model F18D4 watching your video from where you place the thermostat fluid control is broken can I buy it and please what's the name of it thanks

Hello. What is the necessary resistance to a new sensor.

I had P0796 error, valve stuck off, then I replace with new transmission oil. Now transmission oil is leaking out.

Hello. I change outspeed sensor i now my car won’t run on drive? Did i forget something ?

HOW DO YOU TEST IT, SINCE IS CONNECTED TO THE TCM ?

Hiii Ali express Ac delco brand is it taken ?

i changed the sensor, same code shows up. and when it gets to 92°c it gets really stupid, no shifting more than 2nd gear, any ideas?

Класни