Chevy Traverse: Front Brake Job

No video

Chevy Traverse: Front Brake Job

Рет қаралды 143,151

Күн бұрын

Say it's not so! Another SMA brake job! You'll love'em or hate but either way here goes another. -Enjoy!
If an SMA Video has helped you out please consider giving using "Patreon" to help support us. The videos take real time to create and pull us away from real work that pays our bills. CLICK HERE: / southmainauto
CHECK OUT OUR "SMA SWAG" STORE! Go on Teespring and get your very own SMA merch!
teespring.com/...
If you don't like Patreon feel free to use the "PayPal Me" link: www.paypal.me/...
The South Main Auto Amazon Store:
www.amazon.com...
AES Wave Automotive Diagnostic Tools: www.aeswave.co...
Thank you for all the continuing support!
--Eric & Vanessa O.
Feel like sending some swag to SMA because you love the videos but don't know where to send it?
Just ship it here:
South Main Auto Repair
47 S. Main St
PO Box 471
Avoca, NY 14809
Disclaimer:
Due to factors beyond the control of South Main Auto Repair, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. South Main Auto Repair assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. South Main Auto Repair recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of South Main Auto Repair, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained.

Пікірлер: 597

@SouthMainAuto 4 жыл бұрын

Astro Pneumatics on Amazon: amzn.to/2VcY8rv OEMTOOLS 24518 Brake Caliper Hanger Set: amzn.to/3er2DX3 Permatex 24125 Ceramic Extreme Brake Parts Lubricant: amzn.to/2xAHUQ1 3M CX-DR Brake Hub Cleaning Disc Holder 07545:amzn.to/3csVzYm 3M Automotive (3M 07546) 3M Scotch-Brite Roloc Brake Hub Cleaning Disc - 10 Pack: amzn.to/3esQMYq Fluid Film: amzn.to/2KccJ06 Lisle 24300 Speedy Brake Pad Spreader: amzn.to/3afI0tF Mueller-Kueps 460 200 Brake Caliper File:amzn.to/2ViEXNb & amzn.to/2Vf7hjr

@cheryljason9617 3 жыл бұрын

Brother as always great video... thank you for sharing your knowledge with us

@karthiksgarage4087 4 жыл бұрын

Do I drive a Chevy Traverse? No. Do I need to know how to replace front brakes on a Chevy Traverse? No. Do I want to watch Eric wrench on a car and crack jokes and ramble? Yes!!

@timothybarney7257 4 жыл бұрын

Not just yes, but HELL YEAH!

@wim0104 4 жыл бұрын

with ALL the sounds! Best thing on TV since the A-Team!

@CaptainNero 4 жыл бұрын

Yes

@nates.4552 4 жыл бұрын

YES!!!!!!!!

@vernonrice3539 4 жыл бұрын

Traverse sucks? Yes!! Agree with karthik's garage about watching eric? Yes!!

@tacocin 4 жыл бұрын

I laughed when you said, "Pump the brakes multiple times before scaring yourself while backing out." Yup!!! You only do that once! Experience is the best teacher!

@throttlebottle5906 4 жыл бұрын

or hitting the garage door/toolboxes....

@determineddad7935 3 жыл бұрын

Lol done that once. Never again

@brianadams7903 2 ай бұрын

been there, done that. Have the stained underwear to prove it

@lamproslamprou1753 4 жыл бұрын

Why do i hit the like button before even watching the video? Maybe i am fond of this guy (not a sponsor)

@mikeakridge6555 4 жыл бұрын

Me too!

@AntonioClaudioMichael 4 жыл бұрын

@@mikeakridge6555 right

@alfredmorency8296 4 жыл бұрын

On channels, I watch regularly I hit like when I start watching so I don't forget. If I then watch and find it disappointing I go back and remove my like or change it to a dislike if it's terrible. This is easier for me since I rarely see content I don't like on channels I watch regularly.

@jamesbruno5896 4 жыл бұрын

Been pushing pistons in that way since 67 when disc brakes became popular with no issues! Thanks for sharing!

@locomike102 4 жыл бұрын

Yep. Cars, trucks, motorcycles, hell, even mountain bikes. People worry too much.

@FredTheLutinoCocatiel 4 жыл бұрын

It depends if you were working on your own vehicle and you plan on keeping it for a long long time then bleed the caliper to keep fresh brake fluid in the caliper.

@pdaddy879 4 жыл бұрын

I never open the bleeder on my car or anybody else's. I never had a problem and my car is 20 yrs old

@danlevesque5437 4 жыл бұрын

@@locomike102 according to that theory I should never have to ever do a oil change again top it off and keep going no need to worry I might wear out the engine 😊

@roberterdei8627 4 жыл бұрын

Those 1960's ABS pumps must have been alot more robust that than these trashy imported dime-a-dozen Bosch Germany products...

@PatrickJago 4 жыл бұрын

I’ve always just uncapped the master cylinder and pushed the pistons in. Never had a problem.

@1keykneedeep 4 жыл бұрын

Been doing the same for 30+ yrs. Never a problem.

@RileyNA 3 жыл бұрын

Same. Didnt realize there were any discrepancies on that.

@akersjon278 4 жыл бұрын

I had a extended rubber fold in on itself once too. It didn't hurt any, but the child support sure can sting a little...

@throttlebottle5906 4 жыл бұрын

lack of lube newbie :))

@carlosnavarro921 4 жыл бұрын

The brake clean intro never gets old!!

@snakeskinproductions7500 4 жыл бұрын

I changed up the way I do brakes to your method back 3 years ago. I average 5 to 7 brake jobs a week and in that time have not had 1 come back (knock on wood) for an issue regarding this method. have had some for rotor issues and the like but not for install issues. That speaks volumes for me...

@michaelmagnani3463 4 жыл бұрын

I have always just pushed the pistons back in... if they are dirty I just give em a toot with the brake clean

@Cheepchipsable 4 жыл бұрын

Did you ever consider the brakes failed completely, and as a result they are at the bottom of deep, deep ravines and can't come back to complain?

@pbr549 4 жыл бұрын

I always find it amazing how short a vehicles life is in New York because of salting roads. Last year I treated my 1999 Toyota Tacoma to new rotor, pads, and calipers for her 20th birthday. I enjoy working on the Truck. Break pad, timing belt, and sparK plugs for 236k miles so far.

@300DBenz 4 жыл бұрын

FINALLY! 🥳 I finally found someone else who butters the contact points on the calipers instead of slathering the backside of the pads! 👍🏼

@Tadhakes67 4 жыл бұрын

Eric I have been watching you for 4 years now and it is a stress relief just watching you work. It gets my mind off of turning my own wrench 🔧 and just kick back and relax and enjoy. You are an inspiration to future techs. Stay safe

@markplenty2631 4 жыл бұрын

I’ve watched dozens of brake jobs with your channel Eric, and it never gets boring!! Well done! Keep em coming!

@urbanlumberjack 2 жыл бұрын

I change the brake pads on my wife’s traverse this week. It was the easiest break job I have ever done in my life. I know some people don’t like the traverse because it’s direct injection, but every piece of maintenance I’ve done on it has been really simple

@bjqr5763 10 ай бұрын

Everything is simple, but where they put the oil filter…… WTF?

@D4RKGHOST45 10 ай бұрын

@@bjqr5763for my sisters 2019 Lt it was by the radiator I believe I don’t know if that helps but yeah

@hatfez 4 жыл бұрын

Love watching these videos! Very informative and entertaining! I do miss the collage gals. Glad they moved on, but it was fun watching them assist in the shop!

@Shiver2002 4 жыл бұрын

because of this channel I know the following: 1. How to do brakes on everything 2. How to diagnose electrical issues like a total boss. 3. How to crack hilarious jokes that usually get eye rolls.

@SouthMainAuto 4 жыл бұрын

Your welcome haha

@Sicktrickintuner 4 жыл бұрын

But do you have an ice cream machine in the shop yet?

@SouthMainAuto 4 жыл бұрын

@@Sicktrickintuner no :(

@islipfdchief 4 жыл бұрын

@@Sicktrickintuner , Does Eric look like he is 300 lbs? There would be no reason for Mrs. O to make lunch ! Pay attention man, haha. That shop with ice cream would have made a killing last year with the bridge out. Summer job for the kids ?

@Sicktrickintuner 4 жыл бұрын

South Main Auto Repair LLC See, convince mrs O to get one, that way you could have the kids sell ice cream also. If not, snow cones could suffice in a pinch.

@everettprobst5011 Жыл бұрын

I just purchased a 2017 Chevy Traverse on 12/27/2022, this is very helpful and straight forward. 👍

@Pointlesshandle48 Жыл бұрын

I have a 2016. We love it, but change that transmission fluid!! These cars have transmissions with a bad reputation. The only issue I’ve had is the purge valve which was $30 and it’s got 135,000 miles. It’s been a sweet car 👍

@lexteakmialoki5544 4 жыл бұрын

A female friend of mine stopped over my house so I could do her rear brakes. I was having trouble getting the rotors loose. I told her I might have to bring out "Big Nasty". The look on her face was priceless !!

@andykidwell6187 4 жыл бұрын

More Brake Job videos? Keep em' coming! Love it!

@ldean-du5im 4 жыл бұрын

I spray a little silcone spray on rubber to make them fold in correctly.

@geosutube 4 жыл бұрын

IF you can do it, I can do it. This little saying has helped me so much recently, not even dealing with auto repair. Thanks for the encouragement.

@lvsqcsl 4 жыл бұрын

You know, Eric, I have been watching your channel for about 3 months now and I wish I lived in your area. Great video!

@mikeaho4143 4 жыл бұрын

Thanks Eric on this. I also push in the pistons and I've done it for 20+ years. No come backs or issues. I also grease exactly as you do. For what it's worth.

@charlesdavis9755 4 жыл бұрын

A perfect brake video complete with all the sound effects. Even though I don't do very many brake jobs, I bought a piston compressing tool like yours because I got tired of fumbling with C-clamps.

@umpireoba 4 жыл бұрын

If every mechanic was as thorough and knowledgeable as Eric we might pull thru this quarantine

@emporium597 4 жыл бұрын

I'm starting to enjoy the intro to "Big Nasty" (aka "The Dog") as much as I enjoy brake clean's intro. I really need to get out the house. Damn this pandemic. 🤣

@VBshredder 4 жыл бұрын

The big nasty intro gets my chuckling (and throwing up the horns in my head) every time!

@marty0715yt 4 жыл бұрын

Baaa Therapy!!!! Plus the standard-"Brake Clean" Back in the saddle Mr. O Things are rite with the World again. lol

@MikeBrown-ii3pt 4 жыл бұрын

Big Nasty too!

@steventorman3993 4 жыл бұрын

He said, "Fun Fact Friday", I heard something else and had my heart drop. Rewound the feed and realized that he said something innocent. Thx for the clean, fun, informative channel.

@miguelare3 4 жыл бұрын

4:55 "wait for it" brake clean noise 😝🤪

@brucecampbell5917 Жыл бұрын

Just did a front brake job on my 2017 Traverse two weeks ago . It was simple to do and straightforward. My garage , with a fan blowing on me , was still about 100 degrees here in Florida and me being 82 years old , didn't help. Still , it was an easy job . Only got 70200 miles out of the original brakes-- can't expect any better than that.

@williamdyckman9704 4 жыл бұрын

Eric, you show how I want my brakes to be done !! Great video!!

@mikebarnes3238 4 жыл бұрын

Did front brakes on a 2008 Silverado 1500 4x4 yesterday. It was probably my 30th brake job using the SMA method. The owner was looking over my shoulder and voiced a little concern about the lack of lube on the hardware and not using the tube of lube that came with the pads. I explained the logic and ended it by saying If Eric can do it I can do it! He grinned and I gave him the unopened packet of lube. My first SMA brake jobs from four years ago are coming back and they look great and the replacement is Easy Peasy! Thanks Eric

@hectorgalvan8674 4 жыл бұрын

Love the goat sound effect almost woke up the wife last night 😂😊

@DanKuhn 6 ай бұрын

Thank you for immediately saying that they just advise to push the pistons in. Always the hardest part of a brake pad job so now I know.

@ericm8732 4 жыл бұрын

HELLO, ERIC from ERIC, in North Carolina!! My brother-in-law in, and from Florida, has the same name also. He spells it ARIC, but they pronounce it just like our name! It is a legit name if you google it! Thank You, for doing all this for us viewers! YOU, are a "REAL MAN", taking GREAT CARE of your Family! YOU ARE BLESSED! PEACE, and GOOD HEALTH to YOU, FAMILY, and FRIENDS!!.........P.S., Give my Sympathy to the Chevy Traverse owner!! HA,HA,!! "Rah'.!.......................................

@jeffjankiewicz5100 4 жыл бұрын

That reminds me, I `m out of brake clean....used it to clean the carb on a string trimmer,power washer,lawnmower and a chainsaw-landlord`s stuff...bad gas in all of em.Out of FF too...baaaaa. I leave the inner pad in the caliper and use a C clamp to slowly compress piston. I don`t have that fancy tool..lol Thanks for sharing, Stay safe, God Bless.

@jakemason9436 4 жыл бұрын

Never get tired of an SMA brake job....just needed the toot around town to be classic Eric brake service. Thanks.

@adventureoflinkmk2 4 жыл бұрын

Brakleen: 4:56 Fluid Film: 5:43 Y'all can thank me later

@oldanslo 4 жыл бұрын

NAPer (not a sponsor): 5:55

@960Mustang 4 жыл бұрын

Big Nasty: 4:29

@zacariahbingham8021 4 жыл бұрын

if you’re wondering eric no we never get tired of these videos

@wyattoneable 4 жыл бұрын

Like many viewers, I've watched 500 brake videos but I always stop by for the commentary and legendary "one liners".

@michaelplato8692 4 жыл бұрын

😂😂😂😂😂😂😂 I love the channel brother. These sound effects kill me. 😂😂😂💥👊💥

@davelas8465 4 жыл бұрын

There isn't anything better than to start the day with Eric O doing a quality brake job. Always nice! I wish I knew a good sheep joke..

@springfield4522 4 жыл бұрын

Great idea for re-using the wrapping paper! Thanks!

@stephenwgreen78 3 жыл бұрын

Eric, thanks for making a million brake videos😂🤣 Had the shakes when braking and found stuck slide pins...rusted in. If I hadn't watched so many of your videos I wouldn't have even checked & probably messed up my new rotors or kept replacing other parts. Thank you👍

@jsm3737 Жыл бұрын

My first brake job. I spent countless hours trying to push the pads in with the hardware flat. I was getting ready to fire up the welder, and saw your video. Not sure what the welder was gonna do, but I figured what the heck

@DCraig915 4 жыл бұрын

honestly best part of my day come home after a rubbish day at work and relax watching ya crack jokes and ramble on bout life!

@anthonybrogden672 4 жыл бұрын

Your vids are the only thing keeping me sane over here in England during the rona lockdown.😷 I now speak a whole new lingo. 👍

@Thecrazyvaclav 4 жыл бұрын

Yay,brake clean,fluid film,the compressor working and the phone ringing,this videos got it all

@geraldfischer6049 4 жыл бұрын

Just did the FIRST brake job on my 2002 (yes 2002) Sierra at 140,000, but, still enjoy watching it being done!

@matthewleone9568 4 жыл бұрын

4:30 yes to the BIG Nasty music Eric. Yes. Ba da ba ba ba I’m lovin it.

@nkaujthao3781 Ай бұрын

Just finish installing an upgraded brand new brake rotor and ceramic pads for the front of my 2018 Chevrolet Traverse today. My stock rotor just aren’t cutting it when I want to stop suddenly or going downhill slope. I tell you, when those rotor gets hot, the brakes are scary as they just don’t slow down fast enough to avoid front collision. So I made the decision to upgrade the front to a slotted and ceramic pads. The improvement is huge, as for durability, only time will tell. The new rotor and pads was on sale so I grab it while the price is too great to pass up on. Regular price was for $699. Got it it for $275 something dollar

@jptrainor 4 жыл бұрын

Honda also say push the piston in without opening the bleeder.

@macgroober1396 4 жыл бұрын

I used to open the bleeder too, before I used my noggin to think about how a hydraulic system works. Anyone suggesting it hasn't worked on brakes much.

@gregorythomas333 4 жыл бұрын

"Stick it back in the hole until it hits bottom...then twist it" My girlfriend agrees :)

@markh.6687 4 жыл бұрын

So, your girlfriend is a mechanic?....OH! Now I get it! :)

@VortechBand 4 жыл бұрын

Don't forget the mounting hardware

@vernonrice3539 4 жыл бұрын

" And If your shaft is all rusty make sure you clean it first"

@badjuju6563 4 жыл бұрын

New SMA merch should feature this quote.

@raymondhorvatin1050 4 жыл бұрын

Thanks Eric that's everything I ever want to know about a brake job plus entertaining commentary good show and btw I believe you can be trusted

@suavelo5494 4 жыл бұрын

I Strive to be good as you one day. I’ve been in this industry for about 2 yrs & what I don’t learn from my treachery I learn from you.Youve seen it & tell the truth about it. Thanks so much for your time.

@Banshee365 4 жыл бұрын

Eric hitting it hard with quality content lately.

@BOFH402 2 жыл бұрын

I just purchased a 17 traverse. This video is informative and fun. Take care.

@adamUDavies 4 жыл бұрын

Always enjoy watching your brake jobs , easy to follow and thanks for the good jobs. I have noticed that people have been putting a tremendous amount of faith in their brakes as of lately . It's like these people have self driving vehicles?? Stay safe and keep the vehicles even safer.👍👍

@davetopp105 4 жыл бұрын

I use a c-clamp and the old brake pad to push in the piston. That way it's not pushing the piston in off-kilter.

@kenk3102 4 жыл бұрын

...never get tired of your brake videos Eric...keep 'em coming :)

@davidhart5753 4 жыл бұрын

I've never commented on your videos, been watching for years. Love them! Learned a lot. The " but what do I know " comments have upset me. If it's legal thing that just sucks. If it's on account of someone's opinion they can just kiss yours and all the rest of our thousands of butt's! Keep up the good work we love you and all your shop friends.

@bertgrau9246 4 жыл бұрын

I have started replacing the rotors with every brake job I do as well. Ok I have only done 2 brake jobs in the last 3 months. The front of my wife's Lincoln Town Car, and my daughter's 2004 jeep liberty rear brakes and Rotors. They look great and work great too.

@fentonspicerjr 4 жыл бұрын

WHAT A PERFECT DAY! Wife is gone out of the house New SMA Brake Job video Special appearance by BIG NASTY Plenty of Brake Clean used Plenty of Sheep Milk applied as well And lunch is served....... LIKE I SAID PERFECT DAY! Remember Commentators - "If I can leave a comment, you can leave a comment" Thanks for viewing my comment.

@wirenutt57 4 жыл бұрын

Perfect day EXCEPT, no appearance by Mrs. O!

@maxrykowski3550 2 жыл бұрын

thanks for the detailed info. The info you put out saves time so dont have to spend extra time looking up the info.

@Nugetto 4 жыл бұрын

I bet the area that SMA is based in has the best car brake system performance (on a global scale) :D

@johngeyer8444 4 жыл бұрын

My 9yo boy really grooves on Big Nasty. Me too. A tool for boys of all ages!

@keithhastings4092 4 жыл бұрын

Damn...that rotor was better wrapped than any Christmas gift I’ve done....

@antonioponce6544 4 жыл бұрын

I've been doing my own brakes for decades and never, never opened the bleeder valve when pressing in the piston or pistons. Never had an issue. Then one time I was reading how to change brake pads on one of my new cars and the guy wrote to absolutely open the bleeder when pressing in the piston or you could damage the abs. That set me back. I thought about it and figured the brake fluid should be pretty much the same close to that wheel. So I continued doing it my way and still haven't had a problem. Some people just think their way is the best and can't stand it when others do it another. Good job Eric.

@Cheepchipsable 4 жыл бұрын

That might be a good topic for research. Maybe on a modern car you can damage a sensor? I've always loosened the brake fluid reservoir cap first, then push the pistons back slowly, that is to say, I don't force them back. On some Mercedes if you just take the brake fluid reservoir cap off it will set of a warning light on the dash and disable ABS. The warning does go away after a while.

@MrManuel1329 4 жыл бұрын

Best brake jobs on KZfaq I trust your 110 percent because your area is very harsh dirt salt grime hot and cold any brake job that can survive that will definitely do well in other environment. Idc what anybody else says.

@livewire6925 4 жыл бұрын

You are correct on both points. C Clamps for over 50 years doing brakes. ( I have seen a dozen home made tools ) Not lubed during Sub assembly because grease attracts brake dust. Snow sucks! I am so glad I don't have to deal with all that anymore. I have not seen cars that cruddy (under side) in many years. You do an Awesome job. Its also apparent you like what your doing. I still think you have a future in voice over recordings. Franklin,TN

@patrickritenour6935 4 жыл бұрын

Seriously loving the slightly passive aggressive attitude. Bout time you pushed back on all the know it all weekend wrenchers. Been turning wrenches for over just over 14 years and not once have I ever opened a rusty crusty bleeder screw to push pistons back in, or ever greased hardware on the pad side. Go to any dealership you can think of and look at the brakes on a brand new car. You wont find grease on the hardware on any of them. It's for good reason. What do you think happens to that grease once all the brake dust gets stuck to it? Answer is that it causes the pads to seize. Simple, yet excellent video Eric. Ignore the trolls and keep posting please

@jameshughey5747 4 жыл бұрын

BIG NASTY is legit my favorite thing ever

@dejansuturovic7318 4 жыл бұрын

Normal day at a shop😁😁😁😎.Thank you for the video😁😁😁

@danr1920 4 жыл бұрын

I agree about not greasing the hardware. The grease will hold all the dust and grit that comes in contact with.

@AaronBelknap 4 жыл бұрын

"Bro, you didn't use Kroil! Bro, you didn't open the bleeder!" Eric, there are always the professional keyboard warriors. Don't listen to them. I enjoy your video's and believe fully that you do quality work.

@bigmann120 4 жыл бұрын

Eric O has got to be the best mechanic, period! Oh, and DiagnoseDan too. 2 of the most honest and professional techs out there.

@SmittySmithsonite 4 жыл бұрын

My grandpa, my dad, and now me, all pushed the pistons back in during a brake job. My grandpa was working on the very first hydraulic brake systems ever built! None of us has ever had a problem from that. Only time I had to open a bleeder after a brake job was yesterday ... after I knocked a piston out of the wheel cylinder while fighting that 6" long brake cable spring on my '07 Silverado's rear drum brakes! More fabulous GM engineering ... but I digress!

@barrybritcher 4 жыл бұрын

yea I find Toyota say dont grease pins or pad backs only the edges / contact points of pads

@Nitrodr1 4 жыл бұрын

Ahhhh, another day with Eric in the shop. Good way to visit in the evening.

@teacfan1080 4 жыл бұрын

While there are people out there that think they're smarter than anyone else on how to do something, I know one thing. I've watched enough of your videos to come to the conclusion that you DO know what you're doing!

@hyrail73 4 жыл бұрын

Just did a brake job on the wife’s van over the weekend. I remember you mentioning the Muller-Kueps brake caliper file in a prior video. I should have ordered it right then, everyone is out of stock now. Got it done the old fashioned way with emery cloth and the old bastard file. Always enjoy the videos!

@rrabbit1960 4 жыл бұрын

Because Eric O has been mentioning the comments he receives about opening the bleeder I decided to check myself. I have the factory manual for my F150, my Hyundai Elantra, and my old 1994 Ford Ranger along with Chilton and Haynes manuals for several other vehicles and none of them ever mention opening the bleeder before pushing the pistons back in. I even remember from shop class (back in the old days) that all you have to do is push the piston back-just make sure you have enough room in the master cylinder. So unless a manufacturer specifically states that you have to open the bleeder I'm with Eric on this one!

@pablomay28 4 жыл бұрын

I love it when people tell you you are doing something wrong then you look at their channel and they have no content.

@bjornnystrom6697 4 жыл бұрын

Chevrolet!!! Love it. Every. Time.

@briangray5921 4 жыл бұрын

I did my brakes one time on Subaru outback. It was late and I was tired figured I would pump the pedal down tomorrow morning. Of course I forget about it and pile the fam in for a ride. Wife had pass door open and I throw it into reverse out of my garage. It flew backwards and I was madly pumping brakes but not stopping. Only got it stopped by the pass door folding forward against the wall of garage. Not my proudest moment, considering I am a mechanic myself.

@SouthMainAuto 4 жыл бұрын

I should not be laughing as hard as I am haha

@UToobSteak 4 жыл бұрын

Lol!

@buffsheeri 4 жыл бұрын

ooh sorry to hear that, glad no one got hurt.

@AntonioClaudioMichael 4 жыл бұрын

Big nasty and the music just never ever gets old love it Eric O so entertaining @SouthMainAutoRepairLLC

@tdhtdh5173 4 жыл бұрын

I swear I love to work at SMA. I've worked at small independent shops for 18 years and corporate owned for two. Independent shops are where its at! Its just the owner and myself for 13 years we don't have time to babysitting it get in the way of making money!!

@nrvsauto8990 3 жыл бұрын

what you said at 8:40 is exact. I like doing diagnosis , but there are days I wish I just chose to play dumb and only be able to do brake jobs or suspension repair.

@ouch1011 4 жыл бұрын

As an ASE certified master tech with a degree in automotive technology, 15 years of experience and hundreds if not thousands of brake jobs under my belt, I don't open the brake bleeders to push back the pistons. I've never had an issue with ABS units or anything after pushing the pistons back into the caliper, and as you said, that is how most (if not all, Mercedes with their SBC brake system may be the only exception) say to do it. If you have physical junk and debris in the brake system, that is a big problem in and of itself. Don't let the arm chair mechanics in the KZfaq peanut gallery tell you otherwise.

@edwardsilva895 4 жыл бұрын

Love the sheep sound effects lol

@mikechiodetti4482 4 жыл бұрын

Big Nasty and brakkleen. The duo in action! Nice job Mr. O!

@renegade1520 Жыл бұрын

Great video. Gotta do my 2015 pretty soon and you covered a lot of good pointers. Thanks!

@jj69shelby 4 жыл бұрын

So if you say fun fact Friday really quick it sound like f*** that Friday 😆 . great video mister o and commentary .

@Lizardcouple 4 жыл бұрын

I have owned that dual piston compressor for a number of years one trick I learned is to put one of the old brake pads in between the pistons and the tool and will help push them in evenly works great when doing truck calipers like on superdutys that can be tough to push in sometimes.

@willcalderon1990 Жыл бұрын

This video was so awesome thanks. Looking forward to changing my 2011 traverse front ones pretty soon I''ll be using this one .

@brentowen9480 2 жыл бұрын

The only arguments that I think can be made for opening the bleeder and removing the brake fluid is that eventually it's the same as a brake fluid flush. And the bleeder gets some exercise and attention...replacing missing bleeder cap-or it doesn't open...data is gold.

@DonBMW 4 жыл бұрын

I have pushed in pistons on the calipers on all of my cars with no issues. BTW BMW also states not to lube brake pins, but I lightly coat them w some silicone and have never had any issues or stuck pins. Do your thing Eric!

@ZEROORDIELOSER 4 жыл бұрын

I always find my self wanting to watch more of yout videos !!

@alfredislas80 Жыл бұрын

Thanks for making the video. Helped me out a bunch.

@pantherplatform 4 жыл бұрын

Ha! I did front and rear brakes on one of those today and your video shows up on the feed. Wow.

@pantherplatform 4 жыл бұрын

Those cheap steel wheels they use were rusted on so bad I had to use a air hammer to shak'em off. Same thing with the rotors. Had no problems pushing the pistons back in.