Class #3- Chain Alignment

Рет қаралды 27,336

7 жыл бұрын

Calling all BAKER Gearheads!
Class 3 is learning how to align your chain properly.
For any further questions please refer to your factory service manual or give us a call at 517-339-3835.
www.bakerdrivetrain.com

Пікірлер: 20

@johnw8054 3 жыл бұрын

A better and more accurate way to measure is to place a STRAIGHT edge against the outer teeth between both sprockets

@-MrRichBiker1967 3 жыл бұрын

hey parnter, the guy above you, just said that..but you guys are right.

@lucasholt3482 7 жыл бұрын

nice work! tremendously important spec to check for longevity!

@JCcanU 5 жыл бұрын

I Run a EVO 1340 I use a straight edge top to bottom on the inner primary and use the tail end of the dial indicator to the sprocket the way your doing it a short block can be off by 50th and you not know it . use a longer straight edge go top to bottom .

@rafaelbustos4758 Жыл бұрын

Merry Christmas you are the best hope your doing well bought a Franken trany and drive from you 😀

@ralphtieleman4950 Жыл бұрын

Thank you for this video

@mikescheve429 6 жыл бұрын

What are the chances that the primary housing gasket surface was not machined perfectly parallel to the chain face? Should that surface be the datum? If you put a precision straight edge on both gear surfaces, would that verify the .056" out of alignment?

@mafosa8519 6 жыл бұрын

Mike Scheve that’s what I would do. That’s the way the cam sprockets are measured. Off each other. Plus there’s probably some end play not being factored in. Larry

@metatronmen2431 4 жыл бұрын

The video is very much like keep shopping from us guys, for the much Baker charges It can come with some shims for increase or use a demel tool for remove some material for decrease adjustments.

@obfuscated3090 3 жыл бұрын

A Dremel is a poor choice for machining round stock because it's so inaccurate. A lathe or surface grinder (or the correct shim stack in the first place) is the proper method.

@metatronmen2431 3 жыл бұрын

@@obfuscated3090 If i spend $600 for a part i expect to fit right out the box otherwise is garbage because you finish spending over a $1000 dollars including labor and now also need a fitting job, the numbers and work makes no sense in a old bike. I bought this thing and comes with few shims I found the right one for my needs, eventually sold the bike with no problems but I dont go after market no more, personally stick with OEM and replace it when is required.

@openroad6522 3 жыл бұрын

I agree that is not a good way to do it and your block is stamped with letter stamps so it it is no longer flat, unless it was machined flat afterwards. The baker comp I have is not machined well and makes the chain loose tight loose tight, the center hole is not centered

@lqqkout4thedude 5 жыл бұрын

Isn't the compensator bolt a torque to yield and one time use bolt? Do you replace that bolt after taking this measurement?

@openroad6522 3 жыл бұрын

That is my question too

@mikedeuk9351 7 жыл бұрын

What was the measurement for the compensator in the beginning when you first started measuring? You didn't give the reading..

@mikescheve429 6 жыл бұрын

He zeroed the caliper so the second reading was just a differential reading.

@openroad6522 3 жыл бұрын

That shift linkage is bent

@JSmith-cj3yr 6 жыл бұрын

I had to machine .050" off my extension shaft when I did mine.

@uhih6717823 Жыл бұрын

Where oh where is it written that the primary surface is Sq with anything? I am quite surprised at this vid from Baker, and its fallacies. That is NOT how it is done at all to get it squared up. Simply put, wow.....

@uhih6717823 3 жыл бұрын

You have proved nothing