the wheel spinning so damn smooth

neat trick using washers to figure spacer width. super simple

Came here from the 'Moped Army'. Subscribed. Excellent production values - very well done video, in my opinion. Thanks for the content. Keep up the good work. בס'ד

Good looking out bro atleast u showing people

Man, if it wasn’t for this video I would have never known a spacer was needed between that bearing and the brake plate! Could never figure out why the wheel kept pretty much locking up when I went to tighten the axle nuts real snug. Thank you so much.

Hello msr am fan for youre video

Always using your videos to help me fix my puch Ive already watched this video for fun now I'm watching it again because you know exactly what you're doing and I need to know exhaust what I'm doing because I ride this thing every day

With a little bit of knowledge, and few good tools ⚒️ its amazing what can be accomplished .👍🏴󠁧󠁢󠁥󠁮󠁧󠁿

Dude. Thanks a lot. I can use this to fix my rear wheel

Hey thanks for the video, I didn't know they have 29mm bearings. Another well done video, keep em coming.

I’d love to see you take a maxi roller and redo the whole bike from tank to toot with a rebuild, porting. Your bikes are so clean that it’s like working on ferraris compared to what most of us are working on. Like I have a maxi I just tore down to paint with everything in zip lock bags and it’d be really useful to know the things I should do compared to just slapping everything back together. What do I do to the magneto, cables, wiring block, hubs, clutch, ports. All that

I want to get another moped so bad. It's been around a decade since I last had a few.

thanks you sir , that was very helpful to know to make your own spacer*****

been habving trouble with sealed bearings on these Griemca wheels im doing. this video has helped me man. I am having a issue where when i tighten the wheel down in the forks, the wheel is locking up. cant tell if the bearing or the brake pads are binding but i think i need a better and more proper spacer in the middle of the hub between the 2 bearings like you made in this video. anyways, thanks

29mm Bearings!!! RAD! Good vid dude • Honest²

I love your videos so Informative. Do you think you’ll ever do one on disk breaks ?

Hey, nice video! Do you know where i can get these 29mm bearings? They are mostly sold out when i look online. If not, can i use a 28mm with a shim or do you recommend sticking to loose ball bearings in my case?

Hey bud, I have found every thing else that I need to restore my Puch Maxi. I'm restoring this bike mechanically. Not polishing it to sell or make it a show piece. I just need to make it ready for the road this summer... This is the last mandatory service I need to do before I rebuild my entire engine in 2000 miles. I bought the bike with 2086 on the clock. Now bearing 2200 it's so damn fun. My question is I can go to my local HF Tools to buy all the tools I need to complete the job but where do you buy the metric pipe at or the equivalent for my wheel spacers? I wanna do this right and not screw it all up. I have an electric moped so I don't haft to rush. Also, do you recommend straight cut gears for the E50 at all? I am more focusing on hill climbing and more performance for the future. So if you could get back to me on my pipe question I would appreciate that a lot. Thanks-W.

How do I get my freewheel gear off, I have tried all types of stuff- help

Great video. Is this the same for a Puch Maxi snowflake wheel?

can you tell me please for the rear tires

oh shiii ... why am I messing with an angle grinder instead of using a pipe cutter. Dumb!! thank you!

I’m changing 3/4 wheel bearing and axle to 25mm but 25mm bearings are thinner, couldn’t I just make up wheel spacers to fit ?

Does there need to be a washer between the fork legs and the spacer? And does the brake plate need to align with the fork tab to hold it in place?

Are there any major changes in the process for the rear drive wheel? The bearings and brakes seem more or less the same

Use thick walled aluminium tube. Weight saving.

What tyres are they, pal?

Whose the one salty dude that gave a thumbs down? He probably just put in a Treats order for new loose bearings lol I'm thinking of doing this with my Batavus GoGo. At least for the rear, to see how it goes

Anyone know size of that pipe? I'm guessing it's 1/2 inch inner diameter, which would be about 12.7mm ID ?

Hey I just converted my rear wheel to sealed bearings and wonderd what would happen if you didnt use a spacer in between the bearings because a loose ball bearing axle doesnt have a spacer either.

is there a place in the eu where you can buy that bearing ?

What iron pipe size are you using?

What kind of pipe cutter is that, I don't want a crappy one?

i was gonna say i'm pretty sure hobbit front wheels are the same as puch spoke. can you make a video of you one punching a hotdog?

Anyway to keep old vdo drive?