Dump the music, do voice over instead, you will 4x your views.

This is my bicycle, it is just AMAZING and also really appreciate the ongoing support by the guys. 5 stars!

Battery placement always the hardest part to me. Good job, amazing work

I've been wanting to convert my bike for awhile now but every video I've seen has been on bikes with 1by drivetrains so I was pleasantly surprised to see your video featuring the Sport version of my bike, I have the Expert trim.

Nice work. I appreciate your efforts. Looking forward to the next video... Cheers... 🥂

Great video, well edited. What battery did you use? I enjoy your videos keep them coming

Very clean build. 😊

quieter than I thought

This is very helpful thank you so much

kalimera, very nice work 😉

So glad the gen 3's finally did away with square taper cranks.

Hello friend it's going faster then the athletic them bro 😅😊

the wiring is not covered by anything and are pointed at the area where most splashes are coming from the rear wheel. what's the IPX rating for the motor? I know that connectors are waterproof but reality is, that those really are not waterproof.

Seems like a really expensive motor on a really cheap new bike frame with really low end components. Odd value proposition. I would think that most of us are looking to add a motor to a “old” but high spec MTB in the basement.

hi. My bike is equipped with a 500w motor and a 13a controller. I am going to change to a 20a controller. I know that bldc motors can withstand 2-3 times the power, but I wonder if this is true.

אם המורה שלי היה טוב כמוך הייתי מהנדס ,🙏🙏🙏😃❤️👍

Great video,How many miles do you get on this bike, while averaging 30 miles (48Km), does this motor overheat if you using throttle while you doing 30 miles (48Km), no one mansion estimated mileage range, can you also mention top speed and what size chainring you use 32,38,or 42, reply is well preciate it, you also get new subscriber to channel.

Need some EUC content my dude.

Brilliant like the 3d printed mount, where can I fing one of those

Very tidy installation.

I would think the chain and that slotted box would be susceptible to mud.

How much would cost this ? Professionally installed ? And price of equipment?

Cuál batería usaste?

I'm confused. Why the extra chain? Why not drive the chain ring directly like the Bafang BBS mid drives do? I built a similar setup a few years ago using a car alternator as a motor but it was terrible. Maybe partly my fault for poor build quality and maybe the alty motor was not up to the job but the design was poor from the start. Well made video though. 🙂

I would like a primary belt drive to make it quieter

Hi I'm from Melbourne Australia could you tell me the tool I need to take out the bottom bracket the socket and can you use the same socket when installing the cyc kit I have a crank removal tool I have a Norco storm 3 I no you have links but they aren't for Australia if you tell me the tools I need for this kit I will buy them at 99 bikes I love watching you fit kits I have fit a hub motor kit on my gt now I want to get a cyc I think they are amazing and they have torque sensor which I don't have on .y other bike it's pas ans I don't like it.

That chain solution seems so overkill compared to Bafang.

that motor is powerful I broke my Chain and my derailer I dunno how to setup the power in computer stuff

😮why not ride it with protection

Does anyone know how many miles these batteries or these converters give?

which gen? 2?

Where did you get that battery mount at

Relying on solder connections alone without physical connection between wire and terminal is a bad idea.

Can this work on single gear bikes?

Stealth ??

Bafang BBSHD (LUNA Cycle) is less expensive, easier to install, and more powerful. I've installed dozens of them.

Imagine trying without the tool. Never get there.

Upside down is just wrong !!

Horrible

¡Que horrible!. Cadenas y bandas en vehículos eléctricos🤮.