D . Grey Drafting & Design 75mm Machinist Clamps .

  Рет қаралды 9,124

Max Grant ,The Swan Valley Machine Shop.

Max Grant ,The Swan Valley Machine Shop.

22 күн бұрын

A 75mm Machinist Clamp kit from D. Grey Drafting has been generously supplied
for us to machine & assemble .
The kit comes with complete drawings and materials to make 2 clamps .
D. Grey Drafting & Design has various project kits suitable for the home workshop .
d-gray-drafting-and-design.my...

Пікірлер: 133
@samrodian919
@samrodian919 21 күн бұрын
Waffle on Max! Whatever you have to impart is worth listening to mate!
@joell439
@joell439 21 күн бұрын
I couldn’t agree more 👍 ….. Waffle on Max. I have so much to learn. 😊
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
No worries 👍
@TheAyrCaveShop
@TheAyrCaveShop 21 күн бұрын
That's a nice little kit, very well documented. Those little side bits of information are a always a nice bonus. Enjoying the build... Cheers...
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
Thanks Dean . Cheers 👍
@acmemachining
@acmemachining 18 күн бұрын
Nice project building those clamps. I am ordering some for myself. Thanks for sharing.
@swanvalleymachineshop
@swanvalleymachineshop 16 күн бұрын
No worries 👍
@Rustinox
@Rustinox 21 күн бұрын
"Tapping thing" is indeed the right name of the tool, I think... And I hear nothing but positive comments on these clamps, so I suppose they're really good.
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
I wonder if they are as good as your ''Made In Germany Clamps '' ! Cheers 👍
@Rustinox
@Rustinox 20 күн бұрын
@@swanvalleymachineshop Time will tell.
@mickralph4623
@mickralph4623 20 күн бұрын
WAffle on as much as you like mate. I'm loving it!
@swanvalleymachineshop
@swanvalleymachineshop 19 күн бұрын
No worries 👍
@RalfyCustoms
@RalfyCustoms 20 күн бұрын
G'day Max, happy days mate. I've been looking at these myself, and I might go for it after seeing you make it look so easy. Them tapping do da things are hard to identity eh lol, Happy days, and thanks for sharing
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
No worries . You just can not thread up to a shoulder , they make special stepped dies for that purpose . Cheers 👍
@Preso58
@Preso58 20 күн бұрын
Yes, we've all been put on notice for using tee type tap handles with a tap follower! A lot of my taps don't have either a male or female conical centre which makes it even harder to follow best practice. That Coventry die head is a nice piece of kit. I stupidly passed up on the opportunity to "stocktake" one from a capstan lathe that came into our possession many years ago. Regards, Preso
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
Lol , JP is correct in what he said on his video but sometimes we just have to use what is at hand ! I could not pass these did heads up when they came along , i used to use them a lot back in the 80's & 90's so i knew how useful they can be . Cheers 👍
@johnsherborne3245
@johnsherborne3245 18 күн бұрын
You have good, and expensive tastes when it comes to keyless chucks!
@swanvalleymachineshop
@swanvalleymachineshop 18 күн бұрын
Lol , that one popped up on E Bay ages ago for the right price ! They are good chucks ! Cheers 👍
@strykerjones8842
@strykerjones8842 20 күн бұрын
Max you’re quickly becoming one of my favorite online machinists. I don’t know if it’s the interesting projects or the way you approach them but it’s entertaining to watch. Cheers from Phoenix Arizona, USA
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
Thanks 👍
@DudleyToolwright
@DudleyToolwright 21 күн бұрын
As I watch these videos, I am always thinking about how I would make the whatevers and in this case we had similar approaches. It was gratifying to know that I was thinking along the same lines as someone who knows what they are doing. Cheers.
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
No worries . Hey , that small carbide drill you sent was a God send the other day . I had to dimple a hardened shaft for a lock screw ! Thanks . 👍
@sergeantpeppers8858
@sergeantpeppers8858 20 күн бұрын
Great video. I learned a lot. I'm not a machinist, but this is interesting. And the part about the tap holder thing, I loved it. "What the f**k is this thing." Great. Shows someone real, not playing to the camera. Can't wait till the next one. Don't worry about the time. You keep things interesting.
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
Thanks 👍
@colincreedtattoomachines
@colincreedtattoomachines 20 күн бұрын
Max, great start to your DIY "Kant-Twist" Clamps & don't be concerned about waffle, it's good info. As an old Jeweller, we used the same JM "Easyflo" flux & would add in a few drops of dishwashing liquid into the jar, to help it break surface tension & capillary into the joint better.
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
Thanks . I did not realise dishwashing liquid would do that . Cheers 👍
@jdmccorful
@jdmccorful 21 күн бұрын
Your "matter of fact"way speaks years of precision. Thanks for your time and skills!
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
Cheers 👍
@mauricesteer8023
@mauricesteer8023 18 күн бұрын
Looking forward to the next video. Hope you are getting a bit of the rain that's moving over at the moment. Was looking a bit dry there.
@swanvalleymachineshop
@swanvalleymachineshop 18 күн бұрын
Lol , it's been raining pretty good for the last 2 days off & on . At last , but now i am over it !!! Cheers 👍
@huibhoogendoorn503
@huibhoogendoorn503 21 күн бұрын
I made the clamps to, I order only the laser cut legs with the drawings and bolts. Futher you can use material you have leing around so as most of us have. I make 4 and they are working very well. I can recommand them to you all. For the long treaded part I used stainles treaded rod M10x1,5 that works very well.
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
I may have looked at making my own but these came along . The other thing , i was not sure about the pivot ratio as not having one to look at . Cheers 👍
@johnbewick6357
@johnbewick6357 21 күн бұрын
Silver Steel in the UK as well Max.
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
Thanks 👍
@timmienorrie
@timmienorrie 19 күн бұрын
Thanks, buddy, another really entertaining video. I would have used a form tool on the knobs to give a more rounded end but that's just me.
@swanvalleymachineshop
@swanvalleymachineshop 19 күн бұрын
No worries 👍
@StuartsShed
@StuartsShed 21 күн бұрын
Keep on with the waffling and the anecdotes! I was hoping to hear more about the parting incident in 1980.🙂 Neat trick on brazing the bar ends on - certainly never thought to do that. Cheers!
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
Thanks 👍
@bostedtap8399
@bostedtap8399 21 күн бұрын
I hate the term "Tap follower" for some strange reason, I prefer "Sprung Centre", but horse's for course's as its said. Nice work Max as always. Thanks for sharing.
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
Tap thing ! Cheers 👍
@jrd02wilcox
@jrd02wilcox 20 күн бұрын
Excellent video! I look forward to seeing your videos every week.
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
Thanks 👍
@honeycuttracing
@honeycuttracing 20 күн бұрын
All our spring centers have that inverted cone on other side, just pull grub screw out and turn them around, not sure on the brand we have but not near as much play as yours had, we actually keep one with inverted cone stuck out and other one with the pointy tip stuck out to make it simple 😉
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
The other end of this one is flat and hardened ! Cheers 👍
@animal_engineering
@animal_engineering 19 күн бұрын
looks like a cool kit to learn some skills on, when you were doing the parting I was on the edge of my seat ha-ha, looked like you were setting it up at 80 before you moved it closer to the chuck and went 85. definitely good call not to drill right through really wouldn't look anywhere as good as the cups with solder. these will probably be the most accurately built clamps ever. will have to see what freight from Canada is like.
@swanvalleymachineshop
@swanvalleymachineshop 18 күн бұрын
Thanks . I have been meaning to swing past . 👍
@mikewestbrook2319
@mikewestbrook2319 21 күн бұрын
Good show, enjoyed it, thanks Max
@swanvalleymachineshop
@swanvalleymachineshop 21 күн бұрын
Cheers 👍
@AWDJRforYouTube
@AWDJRforYouTube 20 күн бұрын
Great job on the clamps Max...That's the proper soft quiet flame for silver braz'n, I can tell you've done a lot of it!
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
Cheers 👍
@tas32engineering
@tas32engineering 20 күн бұрын
Those Coventry thread cutters take 5 seconds but are over$1000 to purchase. Still always like someone who shows how obviously is enjoying the process. Silver soldering & that green flame ain't known commodities.
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
Cheers 👍
@Warped65er
@Warped65er 21 күн бұрын
Thx for the vid.
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
Cheers 👍
@gagasmancave8859
@gagasmancave8859 21 күн бұрын
Morning Max from UK, nice start to the week. Have been looking at making a pair of these clamps so will, follow yours with interest
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
No worries 👍
@frankerceg4349
@frankerceg4349 20 күн бұрын
Thank you Max!
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
Cheers 👍
@pingwax.
@pingwax. 19 күн бұрын
Such a great channel. Good for a chuckle, too many lessons to count. Top shelf.
@swanvalleymachineshop
@swanvalleymachineshop 19 күн бұрын
Thanks 👍
@brianmccusker3852
@brianmccusker3852 20 күн бұрын
Thanks Max. That die head sure works a treat. Nice work with the camera, cheers.
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
No worries 👍
@annacalise8336
@annacalise8336 21 күн бұрын
I'm fairly new to your channel here in the Eastern United States and love your channel, I really enjoy the longer videos and diversity of work, keep making chips mate, and thank you for these excellent videos!
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
No worries , Thanks 👍
@DudleyToolwright
@DudleyToolwright 21 күн бұрын
I really liked your mod to the spring loaded follower. I am going to steal that.
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
Lol , Cheers 👍
@hmw-ms3tx
@hmw-ms3tx 20 күн бұрын
Over here the tap thingy is called a 'Pump Centre'. Not sure why, it doesn't pump anything, that's just what they're called. Maybe it looks similar to a plunger pump when being stroked? Ken
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
Lol , that sounds like the name of a ''Knock Shop '' Cheers Ken 👍👍👍
@TrPrecisionMachining
@TrPrecisionMachining 20 күн бұрын
very good video friend Max..thanks for your time
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
Cheers 👍
@624Dudley
@624Dudley 21 күн бұрын
G’Day Max, I don’t recall seeing this type of clamp in videos from Oz. They’re as common as drills in the States, where they’re called “Kant Twist” clamps. Marvelous things, offered in a heap of graduated sizes. 👍
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
You are right , i think they are not a common thing here . I have always used & seen the common toolmakers parallel clamps . Cheers 👍
@davidcashin9194
@davidcashin9194 20 күн бұрын
I must have been lucky with the one I go off eBay as I said it has a point and a cone.
@swanvalleymachineshop
@swanvalleymachineshop 19 күн бұрын
I must have been stitched up like a kipper , the picture only showed the pointed end ! 👍
@wrstew1272
@wrstew1272 21 күн бұрын
That threading gizmo is scookem! I think down there it’s referred to as “ fair dincum”? ( that makes spell check nuts! ) What an asset. I’ll never have one, but you scored with the set. Do you set a stop in set up? Looks almost automatic in use.
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
I use the lathe carriage as the stop . Cheers 👍
@907jl
@907jl 21 күн бұрын
I've got threading die envy Max...that thing is cooler than penguin shit!
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
Lol , Cheers 👍
@Paul-FrancisB
@Paul-FrancisB 21 күн бұрын
G'day Max, perfect timing to catch up on a new project 👍. Edit: Made me chuckle when you stopped to explain the tap follower cone Vs point before the keyboard warriors started after watching Joe Pie
@swanvalleymachineshop
@swanvalleymachineshop 21 күн бұрын
Lol . Yes , i made sure i got in first ! If your tap holder is straight , it will still cut a true thread . Tapping heads hold taps all piss wobbly & the tap squares itself up . 👍
@butchphillips873
@butchphillips873 21 күн бұрын
G'day Max, Thanks for the reply to my question regarding parting "upside down" in the last vidio. And I appreciate you showing the parting blades you use here. cheers, Butch.
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
No worries . I will touch on the parting tool in a future video . Look at one of my older video's . kzfaq.info/get/bejne/gtGWorGYxrOoiGQ.html 👍
@cj7jeep81
@cj7jeep81 20 күн бұрын
Was wondering how you got your depth on the drilling, very clever! Will use that idea for sure
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
Thanks . It is close enough for most jobs when drilling . 👍
@richardmills5450
@richardmills5450 20 күн бұрын
I love those coventry die heads. I think ill have to get some. cheers Max
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
They are worth their weight in gold ! Cheers 👍
@apollorobb
@apollorobb 21 күн бұрын
G'Day Max Cant twist Clamps are a Bobby Dazluh and a joy forever in the shop. Cheers Mate
@joell439
@joell439 21 күн бұрын
Cheers 👍👍😎👍👍
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
No worries 👍
@chadstrand7868
@chadstrand7868 20 күн бұрын
great work thanks for the video
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
Cheers 👍
@be007
@be007 21 күн бұрын
those clamps are realy handy, thanks for sharing max. cheers ben.
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
No worries 👍
@Randysshop49548
@Randysshop49548 21 күн бұрын
Hi Max The taping head works really good. Cheers
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
No worries 👍
@DudleyToolwright
@DudleyToolwright 21 күн бұрын
I see you are using Anchor Lube. Did you get that from Stan over at BarZ or was that something you found locally in Aus.?
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
Yes . Bruce Witham bought some back from his Bar Z visit a few years back . I have just kept it aside for special jobs but have been using it a lot lately . 👍
@CraigLYoung
@CraigLYoung 20 күн бұрын
Thanks for sharing 👍
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
No worries 👍
@TedRoza
@TedRoza 21 күн бұрын
G'day Max. Excellent work, Still very impressed with your tapping jig. Everything just seemed to fall into place, wondered where the time went Well done, & very Professional
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
Cheers Ted . 👍
@mudnducs
@mudnducs 20 күн бұрын
Thanks Max! from east Tennessee
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
Cheers 👍
@simpleman283
@simpleman283 21 күн бұрын
👍
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
Cheers 👍👍👍
@davidcashin9194
@davidcashin9194 21 күн бұрын
Ha Max if you undo the hex set screw from the tap follower I think you will find that the other end is a reverse cone I checked mine and it is reversable will wonders never cease.
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
I did . The other end is flat & hardened ! 👍
@RicktheRecorder
@RicktheRecorder 20 күн бұрын
Wonderfully instructive as always. Thank you. Why do you prefer turning with the coarse carriage rack wheel, rather than the graduated compound?
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
Habit . And the compound is not always set dead straight , only eyeballed to the zero degree graduation . 👍
@ianmoone2359
@ianmoone2359 21 күн бұрын
Up to your armpits in projects as usual eh Max. 👍 Was wondering what the hold up was with the JFMT lathe. Will be interesting to see what’s been going on. These clamps look like a fun project & handy tools to have once your done. As I I don’t (yet) have silver soldering capability, could I not just thread and tap the slides & brass cups & loctite them on maybe? 🤷‍♂️ Will have to go look up the kits and see what they cost. Keep up the good work, will be looking forward to the next instalment. 👍👍👍🇦🇺.
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
Cheers Ian . Turn a step on each end of the rod & the caps can be drilled through & peened over . 👍
@markramsell454
@markramsell454 21 күн бұрын
I've seen other machinists have a different angle on the parting tool. It leaves no nub on the desired side, looks like 10-15 degrees.
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
It does have that angle , it is ok for steel but needs to be a bit more severe for brass as the fatter end of the tit was breaking off before the small end . Watch when the tool first contacts the brass . Cheers 👍
@alandawson2813
@alandawson2813 21 күн бұрын
Good evening from the true down under across the ditch, called kiwi land.
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
Cheers 👍
@claybadham1391
@claybadham1391 19 күн бұрын
Hey Max, Question for you. Would you recommend doing an oil hardening process after making the threaded parts? Or are they strong enough?
@swanvalleymachineshop
@swanvalleymachineshop 18 күн бұрын
I would not worry as that steel will not oil harden & i feel it does not need to be hard . The 12L14 steel has to go through a carburizing process or similar to increase the carbon content to harden . Also you would not want the top where the cross hole is hard . 👍
@willemvantsant5105
@willemvantsant5105 21 күн бұрын
Hi Max, I use Iscar tooling and parting tools. I also have a Kennametal parting tool and in my opinion cuts marginally better than the Iscar parting tool. Where do you purchase silver steel, I get mine from Radio Spares Philippines , shipped ex UK. Is there a supplier in Perth?
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
The silver steel was an assortment i found on E Bay a few years back . Can not remember where it came from . I have not looked for a supplier here yet . I think the Kennametal blades use the same or similar insert as the older Iscar ones before the Tang Grip came out . I don't think they can take as much curry as the Tang Grip . Don't ask me how i found that out ! Cheers 👍
@boogiewoogiebubbleboy2877
@boogiewoogiebubbleboy2877 21 күн бұрын
G'day, Max. I'm surprised as a machinist that you didn't already have a set of those machinist clamps in your arsenal. I'm 63 and still use the set I made when I was an apprentice. They were the third tool we were instructed to make in year two. What tools did you make? See you in part two cobber. 👍🏴󠁧󠁢󠁥󠁮󠁧󠁿⚒️
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
I have always only used toolmakers parallel clamps . We made callipers , drill angle gauges , vee blocks , parallel strips & reamers etc . Cheers 👍
@keithammleter3824
@keithammleter3824 20 күн бұрын
Max is slipping! Ref 11:39 - for a few seconds it looked like he was going to wind in the micrometer correctly, with the rachet/clutch knob, and not the thimble like he always does.
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
Lol , i like that !
@keithammleter3824
@keithammleter3824 20 күн бұрын
i would not have silver soldered (brazed) the cups on to the rods. There will never be any longitudinal force, so I would have just drilled for an interference fit and heated them to get them on. Simpler to do and gives a better appearance without needing buffing. Shouldn't the screw be given an Acme thread or buttress thread?
@swanvalleymachineshop
@swanvalleymachineshop 19 күн бұрын
A V form thread is pretty standard with small clamps .
@01thomasss
@01thomasss 20 күн бұрын
21:56 - I think the word you're looking for is Dimple
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
Lol , that's it !!! Cheers 👍
@duanedickey7043
@duanedickey7043 21 күн бұрын
That kit in the US is 375 AUD!
@swanvalleymachineshop
@swanvalleymachineshop 20 күн бұрын
Wow ! I better not stuff it up ! Cheers 👍
@duanedickey7043
@duanedickey7043 19 күн бұрын
@@swanvalleymachineshop I was talking about the cut off tool and insert kit not the clamps.
@swanvalleymachineshop
@swanvalleymachineshop 19 күн бұрын
@duanedickey7043 wow , they have gone up in price !
@user-ud1sx2dm4h
@user-ud1sx2dm4h 19 күн бұрын
Tap follower
@swanvalleymachineshop
@swanvalleymachineshop 19 күн бұрын
That's the one ! 👍
D . Grey Drafting and Design 75mm Machinist Clamps .  Part 2
49:12
Max Grant ,The Swan Valley Machine Shop.
Рет қаралды 6 М.
Gear Box Shaft Heat Treatment And Finish Grinding .
31:30
Max Grant ,The Swan Valley Machine Shop.
Рет қаралды 10 М.
$10,000 Every Day You Survive In The Wilderness
26:44
MrBeast
Рет қаралды 136 МЛН
1 класс vs 11 класс  (игрушка)
00:30
БЕРТ
Рет қаралды 3,6 МЛН
Please be kind🙏
00:34
ISSEI / いっせい
Рет қаралды 58 МЛН
Small Fixture Plate Setup Techniques
15:11
Joe Pie
Рет қаралды 25 М.
Jib Crane Installation: Mounting and Grouting the Crane Mast!
29:24
Keith Rucker - VintageMachinery.org
Рет қаралды 68 М.
Saving the Machine the World Forgot
27:53
Inheritance Machining
Рет қаралды 705 М.
Machining on the Shaper .
38:07
Max Grant ,The Swan Valley Machine Shop.
Рет қаралды 12 М.
Copy Turning Ball Knobs In A Manual Lathe .
27:36
Max Grant ,The Swan Valley Machine Shop.
Рет қаралды 10 М.
Building an Oxikit DIY Oxygen Concentrator
28:09
Signal Ditch
Рет қаралды 3,8 М.
Making a Better Machinist's Screw Jack
26:07
Hersch_Tool
Рет қаралды 20 М.
Machining A Custom Size Pinion Gear .   Part 1 .
40:21
Max Grant ,The Swan Valley Machine Shop.
Рет қаралды 9 М.
Making EASY money from jobs other machine shops HATE.
9:03
Glease Man
Рет қаралды 11 М.
I Bought A Minimill to see if they are Worth It
8:03
Someone Should Make That
Рет қаралды 921 М.
Жёсткий тест чехла Spigen Classic C1
0:56
Romancev768
Рет қаралды 720 М.
5 НЕЛЕГАЛЬНЫХ гаджетов, за которые вас посадят
0:59
Кибер Андерсон
Рет қаралды 1,6 МЛН
Will the battery emit smoke if it rotates rapidly?
0:11
Meaningful Cartoons 183
Рет қаралды 17 МЛН
How To Unlock Your iphone With Your Voice
0:34
요루퐁 yorupong
Рет қаралды 23 МЛН
Apple watch hidden camera
0:34
_vector_
Рет қаралды 62 МЛН