3D printing hack - Finishing 3D prints with less sanding required

No video

3D printing hack - Finishing 3D prints with less sanding required | How to sand 3D prints fast!

Рет қаралды 87,948

Күн бұрын

Here it is everyone, the FASTEST & most effective way to finish your prints with the best quality!
Lots of testing & unseen footage & fails have come into finding out what works the best but this by far is it!
If you're trying to save time & increase your quality of finished products this is it!
Make sure to leave me a thumbs up if you liked the video & of course if you have questions don't be afraid to drop a comment.
Video index is below along with recommended products & what I use for finishing my projects!
Video index
Intro to video, breakdown & what were doing today 00:30
First steps to this process, tips & what to use 01:30
The product were using & its properties 02:07
Dilution for putty, how to apply & tips 03:50
Tips for keeping detailed areas clean & precise 06:00
Benefits to this over bondo glazing putty 06:45
Sanding the putty, tips & early after shots 07:40
Filler primer applied & touch ups for deep defects, primer tips explained 09:20
Why bondo primer is the best to use, sanding tips & more about this process 10:42
Using a more diluted putty to fill in defects 13:00
Using dark primers & why- final shots 13:45
Video recap & thoughts 14:15
Whats on deck next? 16:09
As always if any of my videos have helped or inspired to be sure to post about it & tag me on social media, who knows you might get entered in my subscriber giveaway!
Be sure to follow me on insta & facebook!
Insta-darkwing_dad850
Facebook- darkwing dad
Products in video & what I use in my builds
Dolphin 1k putty
amzn.to/3AkzitB
Bondo filler primer-currently sold out
Bondo filler primer substitute-Seymour PBE primer works just as well!
amzn.to/3mUqEil
Duplicolor filler primer(good alternative)
amzn.to/3N5K1zE
Bondo glazing putty
amzn.to/3Lii2LQ
3M fine sanding sponges (great for crevices)
amzn.to/3UYMspF
Variety pack sanding sponge (120-400)
amzn.to/41x2olA
UK purchase links for upol
montenegro.des...
www.eurocarpar...
www.ecfibregla...
Thats it for now, be sure to click that subscribe button & click to bell so you know when those new videos drop.
Until than.....DW out!

Пікірлер: 273

@secritsquirrel4994 Жыл бұрын

Time is money. And trying to optimize post-processing is so critical when it comes to finishing 3d props. Really appreciate you!

@Darkwingdad Жыл бұрын

Thanks man, just trying to make everyone’s life easier, one layer at a time!

@secritsquirrel4994 Жыл бұрын

@@Darkwingdad Keep up the great work!! Honestly, one of the better channels I've found. No BS, doesn't reiterate the same techniques over and over, and provides experimental proof of concept for new techniques.

@Darkwingdad Жыл бұрын

@@secritsquirrel4994 I really appreciate that man, thanks!

@billverine765 Жыл бұрын

Great method for smoothing DWD. One suggestion I have for everyone is to use a tracer coat on the primer. It takes the guess work out of low spots and pin holes. Just get red or black primer and put a dust coat on top of your last coat of filler primer. When you start to sand, any high spots will burn through the tracer coat immediately, then any low spots will stay the tracer color. This is an old body shop trick that has been around for years. It really, really helps you get a great finish and no surprises when you go to paint.

@Darkwingdad Жыл бұрын

Great tip as always, I’ve mentioned this is previous videos since most primers are grey any matte or flat paint/primer that’s darker on top will work. Always appreciate the pro insight!

@UncleJessy Жыл бұрын

Oh man I’m going to order some of that!

@Darkwingdad Жыл бұрын

It’s awesome stuff, if you have a hard time getting it shoot me a message I’ll hook you up. FYI you can spray it just like the bondo!

@dugabomber5993 Жыл бұрын

On the 1rst layer I recommend going perpendicular with your layer lines. Going parallel can let the brush fall in between the lines. Thanks for the video.

@Darkwingdad Жыл бұрын

With this method the second coat reactivates it and works it in but going with the grain can definitely be beneficial, thanks for the input on that.

@mikemccabe2758 8 ай бұрын

I'm printing a RX-78 Gundam. This video is what I needed. Thank you for show how to use the product.

@Darkwingdad 8 ай бұрын

No problem! Good luck on the build!

@Xizax41325 Жыл бұрын

I watched a video a few weeks back of someone using a card scraper to get their prints smooth. Since then that's been my go to to smooth things out.

@Darkwingdad Жыл бұрын

For big panels & non intricate pieces it’s ok but it often causes gouges, you can’t clean up crevices & still rely heavily on puttys & fillers.

@brentcox6201 Жыл бұрын

just yesterday I tried the other putty with acetone on a biker scout helmet and I will say it worked pretty dang well, so will give this one a try too, still have the dome to do

@Darkwingdad Жыл бұрын

Awesome, great to hear!

@toysforboysrc Жыл бұрын

If you ever have a print that does not have a lot of fine details, you can experiment with thinning bondo with “Honey” or even yet polyester resin. You’ll want to add the same amount of hardener as you would and you’d also want to add the same amount of MEKP that you would for the amount of resin added. Then brush it on very generously and it will self level. Pinhole from thermo runoff of drying too fast or not at all is all practice. The ICING bondo glaze DOES crack it too thickly applied, even if it was in separate applications bcs it does not have enough solids but that’s to make it easy to sand. I used to make my personal mixture when I used to build custom interiors and the job ever came back for any repairs or failures.

@deeznuts23yearsago 7 ай бұрын

I like using p38 car body filler since it sands soo easily and can be sanded soo smooth it’s unbelievable

@zenginellc Жыл бұрын

I had the same issues with the Bondo Glazing Putty! I'm excited to try this instead!

@sunriseshell 4 ай бұрын

WOW! This is it. Such a great, effective and forgiving method.

@Dawnovoir Жыл бұрын

Cheers boss! Thanks for providing new methods and pushing the hobby forward!

@Darkwingdad Жыл бұрын

Anytime! Thanks for watching!

@aberodriguez4149 Жыл бұрын

Nice nice nice you are always a plus for the 3D printing world ! Keep up the great work.

@Darkwingdad Жыл бұрын

Thanks Abe, preciste that my dude!

@anthonyvera8524 6 ай бұрын

Done and done. Purchased today. Thanks

@Blacklistedrook Ай бұрын

Your prints are amazing. Stumbled across your channel a few days looking into silk printing. My question(s) for you are what is your go to printer and slicer for most if not all of your prints? Is there one or two different types/ models you prefer?

@Darkwingdad Ай бұрын

For standard prints I like Bowden fdm printers user cura For klipper I love my k1 max & orca slicer

@toysforboysrc Жыл бұрын

I just got done recommending aerosol primers to a forum member and first thing on my YT I see this video lol 😄.. U-POL does make good cheap stuff! We used to use Kombi at the Mannheim Auto Auction body shop department.

@shaunjedi Жыл бұрын

Just got into 3d printing and your video got randomly recommended. Suffice to say I'm subscribed!

@txwombat7826 Жыл бұрын

Thanks for the Vid - I'll be ready to give this a try shortly...

@Darkwingdad Жыл бұрын

Niceee!

@3DPrintedProps 4 ай бұрын

Nice. I need to try this.

@Darkwingdad 4 ай бұрын

Definitely a game changer! The bondo filler primer is no longer available but if you want email me & I can send you a can! As long as we get away from the rustoleum 2 in 1 lol I watched your video awhile ago thinking “he’s got more patience than me waiting for that stuff to cure” lol love your channel btw!

@Rmayer121 Жыл бұрын

Awesome technique. Will definitely try it on my prints. Love your music choice as well!

@Darkwingdad Жыл бұрын

You will love this! Thanks, seems like I’ll never get to showcase my full playlist…guess I gotta make a lot more videos lol

@KylejvT Жыл бұрын

You can smooth PLA glass smooth by using acetone as a heat transfer. It takes seconds though you need a bit more setup then when smoothing abs with acetone due to the differences. I can go through the steps to do it if interested.

@Darkwingdad Жыл бұрын

I am familiar with vapor smoothing with acetone. It’s ok but it often tends to lose definition & I think for most people it’s something they don’t really want to mess with. I’m personally not a fan of it but to each thee own. I can get pieces smooth so fast using this method I prefer doing this over anything.

@servalac Жыл бұрын

seems like a really nice method, gotta try, Thanks !

@Darkwingdad Жыл бұрын

You’ll love it, def a time saver!

@rmfberry261 Жыл бұрын

looks like a great technique. cool watching your hone the skill and seeing the progress and the payout of all the testing you've done.

@Darkwingdad Жыл бұрын

Thanks for the comment Ryan, much appreciated!

@gordontarpley Жыл бұрын

That looks great. It's been a LONG time since I've seen a product that I haven't tried and this seems fantastic. Thanks for sharing!!!

@Darkwingdad Жыл бұрын

Anytime man!

@ssjronin3972 Жыл бұрын

Appreciate all that you do and share!

@Darkwingdad Жыл бұрын

Thanks for watching!

@vinnyboombots8270 Жыл бұрын

Have you tried adding water to wood filler like the spot putty method? I do it quite a bit, it sands super easy and has no odor except for the normal wood putty smell. It works great on filling seams at a little thicker consistency. I'll also put wood putty on seams and other hard to fill areas and smooth it with a brush and water. Works great. You should give it a try if you haven't yet. Love your videos DW, keep em coming

@Darkwingdad Жыл бұрын

Wood putty is water based so you can add water to it. This however isn’t, so adding water to it will simply make volatile agents less stable & cause adverse reactions. IPA is the other option but acetone works by far the best.

@daveghahn290 9 ай бұрын

I think darkwing thinks you were asking adding water to the upol. I was thinking if trying this method with woodfiller and water as well. your comment is encouraging, I will try it tonite w. both water based silica and acrylic.

@chadydesign 6 ай бұрын

Tried this and it came out pretty great. I didn’t use UPOL Dolphin putty. I tried Kombo Putty which was supposed to be similar but I did see some tiny cracks so I ordered the Dolphin putty. Just gotta wait a week or so for it to be delivered.

@Darkwingdad 6 ай бұрын

If you see cracks it means your dilution is off, was your paste thick or thin after you mixed it?

@EMTBonsai Жыл бұрын

Just make sure it's 100% sealed with laqure after your base coat! Being acrylic anything that touches it acetone, water ipa etc without ot sealed in it will reactivate and go soft and you could get a finger dint or print in it! I work with this stuff everyday it's grast for time and dry time but it jisy doesn't have that total curing mind at ease rigidity you'll find this with stuff if your making masks etc and wearing them out like some do with iron man masks haha! I work with this in my work as a body work specialist alot of pros and cons

@Darkwingdad Жыл бұрын

100% correct, that’s why I mentioned bondo primer which lacquer based. Of course you could let it gas & fully cure but most won’t wait a week or more. I always appreciate auto body specialists chiming in. I started off building custom boxes & worked in repair, I still work in refinishing & restoration & it’s crazy how far we’ve come since bondo & rage gold the last 15 years

@sasquatchman0012 Жыл бұрын

Thank you for this info, I am so new I am still waiting for my 3D printer to arrive 😂

@Darkwingdad Жыл бұрын

Let me know when it arrives, what did you get?

@SmalltimR Жыл бұрын

Love your videos and the attention to detail you put in your work - just perfect!

@Darkwingdad Жыл бұрын

I appreciate it, thank you!

@VenkmanJ Жыл бұрын

Thanks for the tutorial bud! I’m also working on a whole slew of props and building my KZfaq channel for content to help the undiscovered kickass creators out there that don’t know where to start. I appreciate the dedication and drive. Keep it up my friend and I’ll see ya in the feeds!

@beachcomberbob3496 Жыл бұрын

Thank you for going through this experimentation on our behalf. I'm in the UK, and Upol Dolphin is readily available here (at a reasonable price for the home user).

@Darkwingdad Жыл бұрын

Anytime! Glad you can grab it, it’s a great product!

@beachcomberbob3496 Жыл бұрын

@@Darkwingdad Your 'bad weather' event is pretty much a daily, all day, thing for us 😀. 'Making Season' for these kinds of outdoor spraying projects is basically June, July and August. That's why I do a lot of electronics and miniatures during the other 9 months.

@Darkwingdad Жыл бұрын

@@beachcomberbob3496 you should watch my video from august, my house got struck by lightning ⚡️

@matthewjordan2147 Жыл бұрын

cool videos and cool hustle you have man. thanks for the info and keep doing what you are doing. 🤙

@Darkwingdad Жыл бұрын

Appreciate the feedback, thanks for watching!

@josephpk4878 Жыл бұрын

The coverage and consistency of that compound mix is amazing - it lays down almost completely flat, without a rigid applicator! I know that acetone can denature other chemicals, so I wonder about the longterm adhesion and rigidity. Gotta try this - thanks.

@Darkwingdad Жыл бұрын

I know too much acetone can affect talc that’s why I wanted to test this being acrylic. I’ve had no bad reaction or lifting from the fantastic or 1k putty. Than again I had no issues using bondo putty either. Only time will tell but I feel based on its composition of solvents it should hold up well.

@anthonymiller5590 Жыл бұрын

@@Darkwingdad what type of acetone do you use?

@Darkwingdad Жыл бұрын

@@anthonymiller5590 klean strip

@anthonymiller5590 Жыл бұрын

@@Darkwingdad the can that’s label brush cleaner?

@Darkwingdad Жыл бұрын

@@anthonymiller5590 no you want this www.walmart.com/ip/Klean-Strip-Acetone-1-Quart/17208793?wmlspartner=wlpa&selectedSellerId=0&wl13=2533&adid=2222222227817208793_117755028669_12420145346&wmlspartner=wmtlabs&wl0=&wl1=g&wl2=m&wl3=501107745824&wl4=pla-294505072980&wl5=9011684&wl6=&wl7=&wl8=&wl9=pla&wl10=8175035&wl11=local&wl12=17208793&wl13=2533&veh=sem_LIA&gbraid=0AAAAADmfBIo6Rrtqt5MZi_Luc489hwdv4&gclid=Cj0KCQjwi7GnBhDXARIsAFLvH4mlfVuhCAbosYDnQ_syqYRTofCtqGz23LET7n7NHWgYT-LqLhWTYs4aAhhtEALw_wcB&gclsrc=aw.ds

@johnny_mo Жыл бұрын

Thanks for the great tips!!

@Darkwingdad Жыл бұрын

Anytime!

@DanVogt 2 ай бұрын

Excellent video and instructions. I'd prefer music that is more chill, it would be less grating when there's dialogue / silence straight after, but at the same time it's your video and you decide; I appreciate that you shared it all so well. Great technique and result. New sub 🤙🎉🌿

@Darkwingdad 2 ай бұрын

I’m getting better at commentary & music selection no harm in open feedback, I appreciate it!

@DanVogt 2 ай бұрын

@@DarkwingdadCool mate. Your music taste is dope, my feedback is simply technical, to try to improve the good "flow"in editing. It's like when people upgrade their audio mics and get good shotguns or lavs; they forget to add an ambient room tone back into the edit ( without which it's so perfect it feels wrong! )

@Darkwingdad 2 ай бұрын

@@DanVogt I appreciate bro! Definitely something I can improve on, thanks!

@Digital_Jedi Жыл бұрын

awesome video bud!!

@Darkwingdad Жыл бұрын

Thanks!

@wewyllenium 6 ай бұрын

Subbed. Massive effort!

@jakeclauson9863 Жыл бұрын

Or you could use upol reface if you can use a paint gun. It's thin sprayable body filler. If you do it right the only sanding you would need to do is roughing up the surface for the reface to stick and a light sand for primer/ paint to stick to the reface

@Darkwingdad Жыл бұрын

Except people may not have a place to put a compressor. Or an hvlp gun, or a place to spray it. Or clean it up, or just the time it take set up,clean up etc. and the cost! Reface,slicksand,featherfill are all over $130 for a gallon. Trust me I’ve used/use them they are great products but there are more cons than pros the using sprayable body fillers for most builders. This method is light years faster & way more efficient.

@B3D Жыл бұрын

nice tips thanks for sharing

@blake8210 Жыл бұрын

Good info.

@Darkwingdad Жыл бұрын

Thanks for watching!

@jamiewilliams4212 6 ай бұрын

This is awesome! Thanks man! I do wonder if the filler woild work with silicone molding the piece..i know bondo inhibits silicone molding

@Darkwingdad 6 ай бұрын

You definitely could use the upol as it is a poly filler

@briansrcadventures1316 Жыл бұрын

That looks a nice quick way to smooth 3D prints! I can't seem to get that particular brand of Upol Dolphin putty in the UK, the nearest I can get is "DOLPHIN U-Pol 200g 1K RFU STOPPER Ultra Smooth Acrylic Putty". Might be worth a try though as it seems pretty cheap, so I'll order that, plus some Acetone :-)

@Darkwingdad Жыл бұрын

Stopper is the same stuff as the 1k for UK based. Works the same way so your good using that!

@briansrcadventures1316 Жыл бұрын

@@Darkwingdad Good stuff. Hopefully I'll get it from Amazon tomorrow :-)

@briansrcadventures1316 Жыл бұрын

As a follow up, the stuff came today. Dead easy to brush on the Upol 1K stopper thinned with acetone, and it dries in minutes, letting me do a few coats. A half hour so later, I'm sanding with wet and dry! :-)

@Darkwingdad Жыл бұрын

@@briansrcadventures1316 BOOM! best method & results, glad it’s working for you!

@briansrcadventures1316 Жыл бұрын

@@Darkwingdad Thank you. I had tried using "knifing putty" thinned with laquer thinners, but never had as good results as I'm having with this Acrylic 1K putty and Acetone, which is also a less smelly combination!

@_mikeymike Жыл бұрын

Does this work on PETG or just PLA? Thx in advance - great vids!

@jeffstark4488 Жыл бұрын

Love it....😍

@fluxcapacitor 7 ай бұрын

"3D Printed Props" sprays a coat of filler primer first _before_ brushing the prop with glazing putty (he also applies another coat of filler primer afterwards). Would you recommend this step (1st coat of filler primer over the sanded PLA) too or advise against it, and why? Because I see here that you start directly by brushing the thinned putty over the sanded PLA, and spray the filler primer later on only.

@Darkwingdad 7 ай бұрын

Doing a coat of primer first to me is pointless. Regardless the print has layer lines and defects that need filling in which putty will do substantially better off the bat. I personally never have done that nor will I. HOWEVER, applying thinned putty on top of primer after a round or two of sanding/priming on heavily affected areas is a method I use. I highlight it in my wolverine build seen here kzfaq.info/get/bejne/mamirdGrnNKlZ40.htmlsi=62hI4dCH25gsGYjT

@Rjacket Жыл бұрын

Great Video, thanks for the tips. I cant seem to find this in EU. I think its the same product but they are calling it "upol 1k Stopper" Packaging is the same and product description so...

@Darkwingdad Жыл бұрын

Yes 1k stopper is the EU version, they always gotta make it confusing lol

@figuresix Жыл бұрын

Gonna have to try this. Liking the upol fantasic, and helps I can get it for 4 bucks a tube. Im sure I can order this new one for same price. (work at Oriellys) So I get a huge discount. Unfortunately here in Washington state, its nothing but rain, snow, hail still here in April. So waiting for weather to turn to get outside and start priming, sanding and painting. Not good to do in my garage with all my 3d printers and computer. Dust is horrible.

@Darkwingdad Жыл бұрын

This is similar to fantastic but dries a lot quicker & fills a bit better. Both are killer, getting for $4….damn even better! Glad you are liking it, o’reillys has a ton of stuff you can use in finishing. I’m guessing your a duplicolor filler primer guy eh? Lol

@figuresix Жыл бұрын

@@Darkwingdad Yes sir, at 5 bucks a can, cant beat it. I would use Bondo primer but we dont carry it.

@spicethea3258 Жыл бұрын

any idea for something similar in the EU? What qualities and contents am I looking for?

@Darkwingdad Жыл бұрын

Looking some stuff up now for ya I’ll send links

@emal2170 3 ай бұрын

Mix baby powder (starch type) and cheap Amazon UV resin. sand, paint. That's all I do.

@colinmsmall Жыл бұрын

How has your testing of applying it without sanding going? Worth it? Or do you still prefer to sand?

@Darkwingdad Жыл бұрын

You definitely don’t need to sand prior. On high detailed areas I recommend a light intricate sanding & light application but try it without sanding & be blown away.

@colinmsmall Жыл бұрын

@@Darkwingdad have you tried this with petg?

@Darkwingdad Жыл бұрын

@@colinmsmall yes no issues

@idontknowpope 6 ай бұрын

Thank you

@clorpe Жыл бұрын

Are we not allowed to wet sand anymore when using this product since I saw in the comments, when it comes into contact with certain liquids it can go soft?

@Darkwingdad Жыл бұрын

There’s no reason you should ever wetsand putty. There’s literally no reason for it & it’s a waste of time. Sanding this with 320/400 will leave it perfectly smooth & a filler primer will fill in any minor sanding imperfections. The only time you should wetsand is A) your primer before paint if it feels rough or b) clear coat to remove orange peel

@TheHateSpeechChannel Жыл бұрын

Could someone confirm in the UK this stuff is called upol 1k stopper, is it the same product inside?

@Darkwingdad Жыл бұрын

1k stopper is the same product yes

@Serene-Scream Жыл бұрын

👍👍 great info as always. Much appreciated.

@MrItsthething 9 ай бұрын

Very helpful video, I will definitely try this. I do want to ask what plastic your part was printed from?

@Darkwingdad 9 ай бұрын

It’s war machine arm cannon piece

@MrItsthething 9 ай бұрын

What plastic was it made from (PLA, ABS...)? @@Darkwingdad

@Darkwingdad 9 ай бұрын

@@MrItsthething pla

@OliWright Жыл бұрын

Have you tried this with ABS? I'm curious whether the acetone thinning would just wreck the plastic, or result in a better bond.

@Darkwingdad Жыл бұрын

The only way acetone will damage pla,petg or abs is if you suffocate the model or engulf the piece in a vat of acetone. In this method it evaporates so quick no damage will occur. Bondo putty & all aerosols contain thinners & acetone too, they don’t damage the plastics & niether will this. Your safe :)

@OliWright Жыл бұрын

@@Darkwingdad Grand. Might try it on my next prop (having just used mostly knifing putty and milliput to finish a proton pack). Love the idea of painting on a thin layer, and also much easier to see your coverage clearly too.

@enzowelvaert4595 6 ай бұрын

Gonna give this a try. Would this method be safe to use on ABS prints, since u are using acetone as thinning agent?

@Darkwingdad 6 ай бұрын

Perfectly fine on abs. It will only effect abs & warp it if you suffocate it in acetone. When people use the acetone in a vat or container understand it’s constantly being exposed to vapors. This method the acetone evaporates in 30 seconds to a minute. No harm will be done bc acetone evaporates so quickly. Same thing with primers, primers & paint contain acetone & thinners which do not effect the abs bc it gases & evaporates so quickly.

@lauriecrabb1461 3 ай бұрын

I'm interested in trying this, but I am wondering if another thinner, such as mineral spirits, could be used instead? I print a lot of my cosplay pieces in ASA and I don't want the acetone to dissolve the material.

@Darkwingdad 3 ай бұрын

Mineral spirits will not work. That only works on petroleum based products. Understand acetone is already in primers & puttys, it evaporates rapidly, the same as if you were applying an aerosol. It will 100% not eat away at asa or other plastics unless you soaked it in a vat of acetone. Huge misconception people have of acetone, it’s in everything we already use, a-ok to use this method.

@lauriecrabb1461 3 ай бұрын

@@Darkwingdad Thank you! I appreciate you taking the time to respond.

@Darkwingdad 3 ай бұрын

@@lauriecrabb1461 no problem!

@wannabiemuuki 5 ай бұрын

Difference from this and the 1k stopper?

@Darkwingdad 5 ай бұрын

Same product the stopper is internationally distributed

@karenpalsdottir5935 6 ай бұрын

Is this unsafe inside the house? I just used bando putty and wore a mask but it is stinking up my entire house even though i did it in the window sill with a open window. I feel bad for my pets

@Darkwingdad 6 ай бұрын

Definitely do not want to use these products indoors & without a respirator. Always use in a shop or outside with good circulation

@paulesposi Жыл бұрын

would you be able to acetone thin the 3M Acryl green putty?

@Darkwingdad Жыл бұрын

Yes you can!

@Lyoishi Жыл бұрын

Hey have you tried automotive glazes? U-pol makes dolphin glaze and gold glaze(lighter weight?), and a dolphin speed glaze you can sand in 6-8 minutes. The TDS says they have the same or more solids than regular dolphin or the 1k, so they don't just have more thinner? I wondered how well they would self level. You have probably researched this with your recent videos, but it is new to me.

@Darkwingdad Жыл бұрын

Those require hardeners, and although they are good for big flat panels they are still fillers at heart & take more effort to sand. I am a upol fan though, they make great products

@mattlott1113 Жыл бұрын

Can we still spray this Upol like we did with the glazing putty?

@Darkwingdad Жыл бұрын

Absolutely, I did it with the fantastic putty, I can always whip up another video though 1:1 ratio is a good consistency for airbrush or hvlp

@mattlott1113 Жыл бұрын

@@Darkwingdad Nice! I figured so, but just wanted to check. I've gotten a lot of use out of spraying the bondo, so I'm excited to try out the upol.

@Darkwingdad Жыл бұрын

@@mattlott1113 definitely won’t need as many coats, same idea just a little less effort & product needed

@seanmcgannon3433 Жыл бұрын

Hey! love your content and your advice! Unfortunately, I live in France and I can't seem to find this product here. Can you or anyone advice me an equivalent please?

@Darkwingdad Жыл бұрын

Is Tamiya or Bondo available near you?

@panter4971 Жыл бұрын

That's amazing, I've been struggling a lot with sanding, I used a lot of two part car putty but it was really hard to sand down(impossible with hand), took a lot of time and also there were a lot of holes and air sacks, would it work with any acrylic putty tho? Since I am from Europe can't exactly get my hands on that stuff

@Darkwingdad Жыл бұрын

As long as it’s a 1 part putty it should. However I have a video dropping using liquitex you’ll want to watch since it’s widely available overseas

@lonewolve1886 5 ай бұрын

What acetone did you use for the putty?

@Darkwingdad 5 ай бұрын

Kleen strip, you can get it at Walmart,Lowe’s etc

@chrislee4667 Жыл бұрын

After sanding, what do you do/use to clean off the part?

@Darkwingdad Жыл бұрын

A few things you can do. Blow with conpressor Wipe down with tac cloth Wipe down with microfiber & isopropyl

@chazhaze3d 4 ай бұрын

this is a little bit of a bed question. I can make these pieces and they are smooth all over but where it attaches to the bed. I get a very textured bottom which ruins it compared to how smooth i can get the sides and top. You have any suggestions?

@Darkwingdad 4 ай бұрын

Sounds like a leveling issue, what printer?

@chazhaze3d 4 ай бұрын

@Darkwingdad well it just looks like the textured bed. It's an Anycubic Kobra 2 Max

@Darkwingdad 4 ай бұрын

@@chazhaze3d glass bed or pei plate?

@chazhaze3d 4 ай бұрын

@@Darkwingdad pei

@Darkwingdad 4 ай бұрын

@@chazhaze3d is there bulging or blistering on the sides for a bit on the bottom?

@ANewKindOfFearCustoms Жыл бұрын

Can you also use this like bondo spot putty and apply it directly without acetone?

@Darkwingdad Жыл бұрын

Yes, it takes longer to dry (about 20 minutes) but you can do it that way if you’d like.

@iljacoveliers5834 10 ай бұрын

Thanks for the video. On Ebay I can find a U-Pol product called "U-Pol 1K Stopper - Ultra Smooth Acrylic Putty", is this the same product but with a diffferent name ?

@Darkwingdad 10 ай бұрын

Yes if in UK 1k stopper is the same product & dolphin 1k

@1937Brett Жыл бұрын

Hycote filler primer is it any good or noone used it thanks

@Darkwingdad Жыл бұрын

Can’t say I’ve tried it so I’m not sure

@chaospatriot Жыл бұрын

Would it be viable to dilute it even more and air brush multiple thin layers onto the part?

@Darkwingdad Жыл бұрын

You can. I’m doing a video on that soon!

@monster_eh3938 Жыл бұрын

I have a friend who works at a bodyshop and gave me a big pouch of U-pol Dolphine glaze UPO714 ultra fine finishing glaze would it work the same just don't add the hardener or would I still have to add it

@Darkwingdad Жыл бұрын

No it still needs the hardener. You can add a filler honey to it to make it thinner but it’s not quite the same as this. It is a great filler for gaps & deep imperfections.

@Rimbranbt 5 ай бұрын

What acid tone do you use in the video?

@Darkwingdad 5 ай бұрын

Kleen strip you can get it at Walmart

@jaytomchuk5474 Жыл бұрын

not available in Canada

@Darkwingdad Жыл бұрын

Have you looked into bondo plastic metal?

@TomsRiverMalones 4 ай бұрын

Would you recommend the upol 1K putty over the Raptor 1k primer spray?

@Darkwingdad 4 ай бұрын

They’re 2 completely different product. Ease of use & simplicity raptor 1k. Better filling upol 1k. I have a video showing how good the raptor 1k works with filler primer. It is a great combo

@TomsRiverMalones 4 ай бұрын

@@Darkwingdad thanks working on my first project and binging through your channel

@Darkwingdad 4 ай бұрын

@@TomsRiverMalones binge away! Lol

@Seneric 10 ай бұрын

If you want to make life easier for yourself for this kind of work, try looking into some more professional grade materials. Sikkens makes a product called Autosurfacer HB ( High Build ) Its a 2K filler with a very high level of microns per paint layer. Normally speaking these kind of products require an additional layer of filler on top of it, but this stuff is ready for paint once sanded. You could rough sand your parts to 280 ~ 320 grit, apply a plastic adhesion primer and finish it up with the Autosurfacer HB. Paint a tracer layer of black on top of that to help with leveling things out. Sand that stuff down to 600 grit and you can pretty much paint any color / clear coat on it for the best possible result imaginable.

@Darkwingdad 10 ай бұрын

This is geared for people who don’t have the space to have things like compressors,hvlp guns & a designated spray area. I come from an auto body background & im well aware of high build spray fillers as I use ever coat slick sand for years. But even that product the set up & clean up is time consuming. Dolphin 1k is polyester based just like most spray fillers. This has a much faster dry time, waiting 2-4 hours for spray fillers to dry is a motivational killer, not to mention most spray fillers are close to $200/ gallon. Great products but not enticing to most enthusiasts

@thadiuspennington6574 5 ай бұрын

Where can I get Dolphin putty ?

@Darkwingdad 5 ай бұрын

Right here! amzn.to/4anwcoq

@mertz7305 Жыл бұрын

NOICE.

@massymetto76 Жыл бұрын

I don't understand which mix did you do , putty upol with what ?

@Darkwingdad Жыл бұрын

Upol 1k combination putty with acetone

@KEVlNSU Жыл бұрын

what do you use to wipe the dust away after sanding before bondo filler primer spray? Just paper towel or microfiber cloth? Thanks!

@Darkwingdad Жыл бұрын

A tac cloth, I can link it if you need to

@KEVlNSU Жыл бұрын

@@Darkwingdad Thank you! I think i have some of that laying around :) Have a great day

@NateNook Жыл бұрын

Does the upol chip at all? Also what do you suggest to use for filling in gaps over this? I figured body filler ?

@Darkwingdad Жыл бұрын

You can use this for bigger gaps, but body filler if better. You want to use a body filler first, putty second.

@philipjensen6442 Жыл бұрын

Will this stretch with the 2:1 ratio? Or would you say you would run through this fairly quickly with helmets? Great video btw

@Darkwingdad Жыл бұрын

You can do 3-4 helmets with a tube no problem

@KRGraphicsCG Жыл бұрын

This would have been great to use on my engineering prototype and just sand it at 400 grit... I wish they had a clear version of this so I don't need to paint the model (example: Black ABS) and it would be smooth.

@Darkwingdad Жыл бұрын

Ever think of epoxy or clear resin (not sla)

@KRGraphicsCG Жыл бұрын

@@Darkwingdad I do have some XTC-3D epoxy from Smooth-On, but I've never thinned it with acetone and it unfortunately has a 5-7 minute pot life. Also, it alters the fit tolerances

@Darkwingdad Жыл бұрын

@@KRGraphicsCG don’t use xtc look into acrylic resins that might work for ya

@KRGraphicsCG Жыл бұрын

@@Darkwingdad I will have to look into acrylic resins that allow me to smooth it onto a part and sand it easily. Just need to ensure it's clear. I actually stopped using XTC because of the dry time and difficulty with sanding

@hffb27 11 ай бұрын

Thanks for the info, you can probably edit out when say the same thing over and over.

@Darkwingdad 11 ай бұрын

When getting a point across repetition works.

@TacticalStrike-Happe 26 күн бұрын

ok I am gonna do a Chess set... and now it looks like a pain for me to do all 32 pieces... wish there will be a day that we don't have to do this.

@briandoiron8438 Жыл бұрын

What matte black finish primer are you using here? Thanks

@Darkwingdad Жыл бұрын

Rustoleum matte black

@briandoiron8438 Жыл бұрын

@@Darkwingdad Appreciate it. BTW, do you still have your discord server? I've found an older link but seems invalid.

@Darkwingdad Жыл бұрын

@@briandoiron8438 yes it’s on my link tree, that link is in the description on my last video

@briandoiron8438 Жыл бұрын

@@Darkwingdad Haha, found it right after I sent the message 😂

@nickhildenbrandt4529 Жыл бұрын

Where do you buy UPol 1k putty?

@Darkwingdad Жыл бұрын

Amazon

@EMTBonsai Жыл бұрын

Pretty much the same as every acrylic based putty in the scale model market I use! The enamel based one is great with IPA it works the same sort of way water would also work the same probably better if it's full acrylic based putty acetone is something I'd use last IPA would be better for the plastic than acetone, Dulux materials acrylic putty is the best on the market bar non every modelers go to really

@Darkwingdad Жыл бұрын

IPA doesn’t dilute this as prominently & there’s absolutely no reason to think the acetone is going to affect thermo plastics in small amounts. Acetone is already in numerous puttys along with thinner. Both are in primers & paints & have no adverse affects due to rapid evaporation rates.

@NK_Customs Жыл бұрын

@@Darkwingdad I wouldn't recommend using acetone in combinations with ABS, as ABS can be dissolved in Acetone, Just like those "smoothing vapor chamber" for ABS 3D prints. And indeed, both are being used in paints, adhesives, etc. without issue's ;-)

@Darkwingdad Жыл бұрын

@@NK_Customs total different when you are suffocating the model in acetone vs it evaporating in seconds with whats shown here. I’ve tested pla,petg & abs & there’s no issues. Remember, acetones,ketones & lacquer are all in aerosols & primers, so saying not to use this method is like saying don’t use spray paints. Any plastic you leave in a vat of acetone or vapor smooth it with no escape from it it’ll damage. But as stated this dries & evaporates in seconds. No issues here.

@matthewromeo9812 Жыл бұрын

Great video! What layer height do you print with?

@Darkwingdad Жыл бұрын

Really depends. That piece was .32 I’ve changed to .28 for a lot of prints & more detailed pieces .2

@RLCPLUMBINGLLC 11 ай бұрын

Could you spray the putty?

@Darkwingdad 11 ай бұрын

Absolutely, I’m doing a video soon on it

@TheJQverse Жыл бұрын

I use the Upol fantastic 0924 but need a way to thin it down. Would acetone be the best way to do so and does the acetone eat through the PLA at all?

@Darkwingdad Жыл бұрын

Acetone will work the best, no need to worry low amounts of acetone will not affect the pla.

@SuperDuperTango 4 ай бұрын

Are you still recommending this product these days? Also, what are your thoughts about spraying this like your videos about spraying the bondo putty? Thanks!

@Darkwingdad 4 ай бұрын

Yes dolphin 1k is superior to ANY putty out there & it’s sprayable. Doing a video on that too

@SuperDuperTango 4 ай бұрын

@@Darkwingdad Sweet! Thanks!

@damienmoreau3859 Жыл бұрын

Quick question: can you make the Upol liquid to spray it like you did with the Bondo?

@Darkwingdad Жыл бұрын

Yes you can I’m going to do a video soon to show everyone

@damienmoreau3859 Жыл бұрын

@@Darkwingdad love you ❤️ So basically for EU it's the 1K Stopper right?

@Darkwingdad Жыл бұрын

@@damienmoreau3859 yes

@Darkwingdad Жыл бұрын

@@damienmoreau3859 I was able to use upols fantastic putty in a mini hvlp. I will have a video soon showing it in an airbrush. I’m also going to show/test liquitex as well.

@chrisjhart Жыл бұрын

Can this be wet sanded? When I've used acrylic fillers before they tend to lift the second you try to wet sand. Great video, thanks :)

@Darkwingdad Жыл бұрын

You don’t need to wetsand any filler or putty nor should you. Only time you should be wetsanding is after your final primer before paint & after clear coat to reduce orange peel.

@chrisjhart Жыл бұрын

@@Darkwingdad I mainly wet sand so it stops dust. Works really well

@Darkwingdad Жыл бұрын

@@chrisjhart understand you are introducing a solute which can prolong curing & affect adhesion with top coats. I don’t recommend wetsanding puttys

@chrisjhart Жыл бұрын

We are going to have to agree to disagree on that one. The only real purpose of wet sanding is to provide a lubricant so it doesn't cut as roughly. I've a whole packet of the stuff ranging from 400 to 1200. I always wet sand where I can for the reason that you are not putting harmful dust into your work atomsphere. Yes, with acrylic it tends to delaminate it, but everything else is good to go in my experience.

@Darkwingdad Жыл бұрын

@@chrisjhart to each there own but you did express issues when you wetsanded & I explained why it’s happening-your adding excessive & reactant solute to the substrate. Following automotive body repair (which are all the products I use & demonstrate with) wetsanding isn’t recommended or used. Dust is something you have to deal with, that’s what ppe is for. I’ve had zero issues pyramiding my grits dry, the dust I just deal with 🤷🏻‍♂️ I’m just demonstrating what professionals used & have used in automotive restoration & what works in my methods. There’s methods & products that others use that I never would, at the end of the day I guess if it’s working for you roll with it. Difference of opinions are like hairs in your head, & unless your bald theres too many to count.

@malcolmpaterson5881 Жыл бұрын

Hi, I've seen people in the UK recommend Liquitex modelling paste mixed with water. Are you able to test this method and review please?

@Darkwingdad Жыл бұрын

I can, I actually got some the other day. Test i shall!

@malcolmpaterson5881 Жыл бұрын

@@Darkwingdad excellent, thanks you so much🙂

@triton6597 Жыл бұрын

Hey man, by any chance do you play in the adult hockey league? I’m pretty sure I ref where you play. Small world I got into making cosplay two years ago by doing a mandalorian costume and a Bo Katan costume I started 3-D printing myself a couple months ago prior to that I was buying 3-D prints at finishing them. I’ve used your videos to help with that.

@Darkwingdad Жыл бұрын

I do, unless your the ref with glasses I’ve never yelled at you lol glad the videos are helping. I wanted to 3D print a puck in petg and see how long it lasts….get me 10 extra minutes of ice let’s make it happen lol

@darren990 Жыл бұрын

nice

@3D_Zaga Жыл бұрын

i paint my parts whit water washable 3d printer resin then i cure it whit UV light

@Darkwingdad Жыл бұрын

Works ok, definitely not as fast or efficient. More toxic & ppe required, the process in the video still needs ppe hit significantly faster & better results.