“ take it off , blow through it , Blow through it Do not suck through it , because if there’s mice inside you do not want to inhale a mouse “ ha ha ha I laughed at that , Cheers jimmy

Headed out to the camper to try a fix. Thank you for making this video. Really enjoyed the humor, the accent, and the fact it wasn't too long!

Dave , It`s always good to have a clear hole and no crushed bottom ! Great vid Mate Rob NSW Australia 3c last night here , heater on all night !

If you use an appropriately sized coach screw, you can thread it into the atomiser screen and remove it with ease 👍

Howdy. My Afterburner is due to arrive any day...and come Wednesday 12/16-17 I'm facing 30 cm of snow in a blizzard! Thanks for your videos

Thanks very much for this. Just did a successful service today and has solved my "error 1" issue. 👍

Another great job David 👏👏👏

I live in my truck and it JUST crapped out on the last cold day of the year. Ill be building a new tiny home as a shed and will be moving it eventually but as its summer I dont need to rush. Ill be sure to reference this video when Im ready to reinstall.

Great video, just FYI with your spare burn chamber, you couldn't get your pick through because the screen was in the way.. that means the screen wasn't fully seated, the screen should never block that hole. Thanks again great video!

Super helpful thank I did not know that these required servicing until a friend mentioned it.

A bit of tlc goes along way to keeping it in good nick, hoping to see you still doing the same in 5-10 years and to see how long these can be kept in decent working order :-)

great video David keep them coming mate

Thank you for the most comprehensive videos about these heaters. I installed a new glow plug, didn't want to ignite anymore after only a couple of days of use. Still does not want to ignite, only feable attempt after manual priming and now smoke was coming from the glowplug when i turned it of, which i presume is not normal ? Opened it up to clean everything but not especially sooted although all the gaskets were old it seemed, ordered new ones.

Cross threaded is a good as a locknut, once.....

Your video is fairly clear on the process except the orientation of the screen. Does it go vertical on there, or left to right over a nozzle, or does it just lay down in the hole any which way?

Ace video. Thanks so much for taking the time to film and share. What size is the box spanner? Mack and Maggie, Huddersfield

Great video. Which heater do you recommend?

Fantastic video... I have the heater that has hot air and hot water ( featured in one of your previous videos) , I was wondering weather I can fit a thermostat to it? Or does it have a built in thermostat that I have not found yet? My controller is exactly the same as yours ( except for the Chinese writing) red block, two silver buttons, one yellow nob... any idea?

_What's funny is I just got my order of twenty atomizer screens in the mail from China today._ _Oh, just unplug the F'n wires! LMAO_

You can take that up with a big wood screw screw it in lightly and just pull it up doesn't damage anything

I use a corrugated iron hammer in screw to remove the mesh ond they usually come out without damage

Love it mate, from Australia 🦘

Now that was a good video! Understood everything. Thank you. Is this a once a year thing? How about every 5 years?

Hi David. Have you heard of a continuous use lifespan for these things?

Hello mate you do make me laugh. Have you done a clip yet of the heater burner chamber with the fan end chopped off. Decoke mine after 4 months on lowest setting and once the stainless atomiser was removed I noticed wire down the glow plug hole wrapped around the centre cog looking unit. With fishing bait hook managed to pull lots of stainless steel out of the burn chamber that’s impossible to clean. Yes had endoscope down hole and it’s like a armature in there. Yes tried ultrasonic with cold brake cleaner but way of checking for sure if it’s clean. Found copper grease good for new gaskets with a tiny paint brush as it doesn’t break them every time it’s dismantled. Waiting on new burner before taking the 4 rivets off the fan end and taking off the end cap. Cheers Gary

Mr. Mc lucky if you take lag bolt w thick threads and shove it down the screen hole and twist it grabs the Screen and u can pull it out, doesn't even destroy the old screen.

Dave, I’ve also seen guys use a certain diameter of wood screw to do this. I unfortunately do not remember that diameter though.

what happens if you put a turbo on it

Pokey things and jiggly things are essential tools in the shed and workshop... :P

I wanted to see it start. !:-)

Hi David. I have the 5k heater and all WAS good. Now its starts but never gets past first green bar, then pump cuts out. Have checked and cleaned entire unit. Intake and exhaust all clear. Changed temp sensor and glow plug, new pump comes tomorrow. Nothing obvious wrong. Leisure battery shows 14v and has just been charged. However heater control panel shows heater is showing only 10v or thereabouts on trying to fire up. All was great until a few weeks ago. Any ideas bud?

David you could narrate paint drying and it would be fascinating.

I have a small amount of soot that will come out of the exhaust tube when I fire up my heater. Do you think this would call for me cleaning out the burn chamber or do you think it's not that concerning? I only notice it because I can see the contrast on the snow. Thanks!

I have an airtop 2000st, do you have an electrical wiring diagram?

When you said "if you don't want to unplug the Glow plug wire from the ecu to remove " I thought this should be interesting, Usually something I say when demonstrating something 😂

Great Video - what size is the box socket ?

I am mixing gas(petrol) and diesel. At 25/75 mix. With gas the 25% do I need to adjust fuel setting or just run as normal and hope it keeps running?

Hellllloooo David - Hope you have been keeping well - I finished my Boat install Xmas week and I am very warm - I plan to make a short video (not too in depth) - Could I use your youtube links to give people advice especially on the servicing of one of these heaters?

Good evening, I'm in a pickle with my heater. T'other week I had the E03 code. Changed the glow plug but couldn't get the atomizer out. It wouldn't work. I then changed the atomizer and plug again but still says e03. On priming it smokes inside... As in a bit of smoke comes out the warm air vents. I am pretty sure my external exhaust and air inlet are ok. The glow plug kit came with gaskets... So, do you reckon I have to do a full strip and replace the gaskets? That gunna be blummin awkward if so. Cheers 🙏

Hi David, could you give me a hint about where go get a decent fuelpump? Within a 1 1/2 years, I am at pump #4. The first one failed after about 4 months, the second after 15 hours, the third lasted 3 hours only (eBay versions). Thanks up front for any suggestion 🙂

How often would you service one of these units? As in, after how many hours of operation? - I have an '8kW' unit on its lowest setting keeping the frost off the workshop at the moment so was just wondering how often I should inspect/service - only run on pure diesel :-)

hi david as YOU ARE D MAN.. how often should said filter be changed ? thanks... going to be cold here till new year. its the only heat we have

Do you happen to have the link to the packet of screens? I could only find the single ones.

Hey buddy! Hoping you can help me with a clamp meter. I dont know much but truly looking to learn! I want to purchase a clamp meter under 200 for AC AND DC current I'm looking for something SAFE/WELL PROTECTED and capable of reading AC AND DC current from .5 amps to 60 amps as accurately as possible through the clamp. Do you have 1,2 or 3 suggestions. I was looking at the Klein cl800 but someone told me it will not read AC AND DC current through the clamp down to half amp accurately..... THANKS FOR ANY HELP YOU CAN PROVIDE ME

listen to david, use the 10mm box spanner, i put a needle nose pliers on it just to see how tight it was....... BIG mistake :-( its so easy to break and the bastard did. New part coming tomorrow! but save yourself the hassle. Great vid Dai 😍🤪

How often should this be done , my heater starts clicking as if it's going to start then suddenly turns off !! Plugged smaller heater into the inverter and now that turns itself off too ! Any idea's ??

What size is the box spanner? I'm getting a service kit together...

Does the Chinese Espar Planner all use the same size atomizer screen ?

Do you have a link to the 10 pack of atomizer screens David, thanking you very muchly :)

Helloooooooo! Trying to find a petrol coolant heater for my car, but all the Chinese ones are diesel only as far as I can see, any suggestions? Thanks!

I was to the understanding that the glowplugs was fastened with a nut from the inside. Maybe thats the older burners 🤔

Would this solve white smoke problem

What size socket for glow plug? Thanks

Hi David, Loving your channel, I have a Chinese diesel heater(all in one),worked well for about three to four weeks.........then it just stopped working, showing error code E-6 (fan issue). Tried all the usual fixes,all to no avail,fan is not stiff or sticking or catching anywhere ????????? Really losing patience with it now..........have you ever come across this issue before,I am all out of ideas ???????? Great channel,like your style, hope you can help me with my dilemma ???????? Kind regards, John.

What do these things run like on Kerosene/heating oil?

Always keep your hole clear hahaha

David what's the model of your power supply please?

How often would this need to be replaced?

Thanks for the video. Smoking a mouse haha.

Of course you have to fuckin unplug the glow plug lol please speak you mind. I always like you videos

Very helpful thankyou I was blowing but the mouse was sucking ha ha ha

What size box wrench please?

yay

👍

im getting ready to install my all in one heater in the red box its all aluminium i cant believe it

Cool last name

Always unplug the wires when changing the glow plug otherwise you will twist the wires and could snap the plug like I did!..😂

10 Pcs Mini Glow Plug Burner Strainer Screen For Diesel Air Parking Heater Parts Condition: New Quantity: 1 4 available / 1 sold Price: £4.85 Estimated between Fri. 8 Jan. and Wed. 17 Feb. 😳😲🙄

5:55 😂😂😂

Instructions unclear...inhaled mouse :/

carbonized.

Try not to make a MESH out of it

Nothing worse than mouse inhalation.

Add public comment...

Damn only 3rd but first comment! Duck ya !

Atomisers, £3 for ten from China or after Jan 1st 2021, £3 plus import duty plus Royal Mail duty collection fees. Good this Brexit WTO shit isn't it.